SteeringColumn92-up.JPG
7761 hits | 99.14 KB | Posted: 10/8/06
Items #26 & 34 are known to get loose; #28 is known to wear.
Items #19 & 25 are known to break, an...

SteeringColumn92up.JPG
423 hits | 100.24 KB | Posted: 1/13/09
Replace http://www.supermotors.net/registry/media/441108

Steering Column wAirbag.jpg
874 hits | 75.22 KB | Posted: 1/24/05
Combine http://www.supermotors.net/registry/media/441108

SteeringColumnExploded.jpg
823 hits | 84.59 KB | Posted: 11/7/05
Combine http://www.supermotors.net/registry/media/441108

SteeringColumn92.JPG
3578 hits | 48.94 KB | Posted: 10/14/07
TSB 96-23-01 Clicking Heard When Turning Steering Wheel
Publication Date: NOVEMBER 4, 1996

FORD...

SteeringColumnAssy.jpg
767 hits | 72.6 KB | Posted: 11/7/05
Steering Column Assembly
1A Screw N803942-S100
2 Steering Column Gear Input Shaft Coupling 3A5...

01NoBoot.jpg
2597 hits | 42.85 KB | Posted: 1/28/06
The boot was torn & degraded, so I removed it earlier. It's not available from Ford, but I found on...

02Cylinder.JPG
3253 hits | 45.41 KB | Posted: 1/28/06
First, remove the lock cylinder by turning the key to RUN, then pressing the release button through ...

03CylRem.JPG
2894 hits | 45.28 KB | Posted: 1/28/06
This is the button. When the key is rotated, the button will be forced back out.

04TiltLevr.JPG
2528 hits | 43.05 KB | Posted: 1/28/06
Using the provided flats, unscrew the tilt lever.

05ShroudScr.JPG
2340 hits | 47.86 KB | Posted: 1/28/06
Remove the 3 lower shroud screws. It may not be necessary to remove the knee bolster.

06HiddenScr.JPG
2386 hits | 38.31 KB | Posted: 1/28/06
If this screw is installed, remove the knee bolster & then the screw.

07Wire.JPG
3559 hits | 60.77 KB | Posted: 1/28/06
Trace the Transmission Control Switch (TCS) wire from the shift lever to its connector, & disconnect...

08WireRoute.JPG
3689 hits | 71.25 KB | Posted: 1/28/06
Trace the Transmission Control Switch (TCS) wire from the shift lever to its connector, & disconnect...

11WireOut.jpg
2969 hits | 66.25 KB | Posted: 1/28/06
Remove the wire from its guides & retainers.

09PinTop.JPG
2690 hits | 59.59 KB | Posted: 1/28/06
This is the shift lever pin. The knurled end just below the head retains it in the pot metal castin...

10PinBot.JPG
2338 hits | 56.61 KB | Posted: 1/28/06
Push the pin out to remove the lever.

12PinDrive.JPG
2352 hits | 54.77 KB | Posted: 1/28/06
It may be necessary to tap the pin out with a small hammer & drift.

13LeverOut.JPG
2209 hits | 58.51 KB | Posted: 1/28/06
The lever can now be removed from the shifter tube.

15BootLever.JPG
2185 hits | 50.69 KB | Posted: 1/28/06
Feed the TCS wire through the boot & install the boot onto the lever.

16LeverOn.JPG
2183 hits | 47.82 KB | Posted: 1/28/06
Install the lever & pin, and then clip the boot down.

17BootOn.JPG
2097 hits | 63 KB | Posted: 1/28/06
Ensure that the wire is routed clear of any moving parts, and connected.

18TiltLever.JPG
1854 hits | 29.86 KB | Posted: 1/28/06
Reinstall the column shrouds, knee bolster, lock cylinder, & tilt lever.

19Finished.JPG
1831 hits | 45.36 KB | Posted: 1/28/06
Finished

Column1.JPG
2188 hits | 48.26 KB | Posted: 1/28/06

Column32.jpg
1855 hits | 43.05 KB | Posted: 1/28/06

Column 96 L.JPG
1940 hits | 49.22 KB | Posted: 2/3/06
For more info, see this page:
http://www.p71interceptor.com/steering/column/disassembled/pictures

Column 96 R.JPG
1847 hits | 49.85 KB | Posted: 2/3/06
For more info, see this page:
http://www.p71interceptor.com/steering/column/disassembled/pictures

IgnitionRodTilt.JPG
2129 hits | 73.2 KB | Posted: 3/30/06
'92-up steering columns use a plastic gear rack between the lock cylinder & the ignition switch.

ClockSpringExploded.jpg
2499 hits | 56.62 KB | Posted: 2/3/06
Clock Spring Exploded
Don't take the clock spring apart - it's not serviceable or repairable.

ClockSpringRemoval.jpg
2239 hits | 40.57 KB | Posted: 2/3/06
Clock Spring Removal

Clock Spring Removal.jpg
903 hits | 40.57 KB | Posted: 2/6/05
Combine http://www.supermotors.net/registry/media/288139