DSCN1792.jpg
2395 hits | 44.08 KB | Posted: 4/15/05
TTB SALUTE!

DSCN1818.jpg
1831 hits | 56.31 KB | Posted: 4/15/05
Flatbed F250 came in handy

DSCN1821.jpg
1218 hits | 46.69 KB | Posted: 4/14/05
brake/kingpin view

DSCN1819.jpg
1189 hits | 45.87 KB | Posted: 4/15/05

DSCN1820.jpg
1168 hits | 33.04 KB | Posted: 4/15/05
Heavy Duty 1/4 plate reinforced diff cover

DSCN1823.jpg
1286 hits | 54.67 KB | Posted: 4/15/05
Detroit Locker, 4.88s

DSCN1822.jpg
1189 hits | 47.04 KB | Posted: 4/15/05
Warn hubs

SpringPerchRelocation.jpg
1371 hits | 7.36 KB | Posted: 4/15/05
Spring Perch "template"

DSCN1840.jpg
1160 hits | 44.12 KB | Posted: 4/17/05
Mocking up accordian frame bracket

DSCN1841.jpg
1185 hits | 38.72 KB | Posted: 4/17/05
Drivers side bracket cut and mocked up into place, looks good! lots of area to weld it on

DSCN1842.jpg
1037 hits | 39.36 KB | Posted: 4/17/05
Both brackets cut-out

DSCN1843.jpg
1080 hits | 28.99 KB | Posted: 4/17/05
sway bar bracket/bumper mounting area needing modifying

DSCN1844.jpg
1131 hits | 48.95 KB | Posted: 4/17/05
another shot

DSCN1846.jpg
1155 hits | 41.19 KB | Posted: 4/19/05
Swaybar Bracket/lower bumper mounting removed

DSCN1847.jpg
1190 hits | 48.19 KB | Posted: 4/19/05
Engine Crossmember- still deciding whether to remove, trim, or leave alone

DSCN2031.jpg
1154 hits | 42.49 KB | Posted: 5/5/05
beginning of front hangers

DSCN2033.jpg
1080 hits | 35.99 KB | Posted: 5/5/05

DSCN2034.jpg
1119 hits | 32.36 KB | Posted: 5/5/05

DSCN2037.jpg
1086 hits | 44.25 KB | Posted: 5/5/05

DSCN2038.jpg
1237 hits | 49.72 KB | Posted: 5/5/05

DSCN2041.JPG
2132 hits | 88.53 KB | Posted: 5/8/05
Front axle hanger tacked into place until final fitting and measurements

DSCN2045.JPG
1335 hits | 59.21 KB | Posted: 5/8/05
Axle perch cutting to move leaf spring spacing from 32"-36"

DSCN2046.JPG
1319 hits | 87.79 KB | Posted: 5/8/05
How much i cut off, I used a chopsaw and cut it by hand, with great care and welding gloves on, and ...

DSCN2047.JPG
1183 hits | 69.56 KB | Posted: 5/8/05
mocked up

DSCN2048.JPG
1167 hits | 52.96 KB | Posted: 5/8/05
Tacked in place until final fitting

DSCN2151.jpg
1143 hits | 39.54 KB | Posted: 5/18/05
will drill the rest of the holes for this bracket once i check to make sure shackle angle is decent.

DSCN2155.jpg
1057 hits | 33.76 KB | Posted: 5/18/05
the brakelines that were on the built D60 when i got it, seem to hookup to the TTB hardlines just fi...

DSCN2156.jpg
1076 hits | 23.14 KB | Posted: 5/18/05
no leaky leaky

DSCN2157.jpg
1125 hits | 48.69 KB | Posted: 5/18/05
Hooked up to the TTB hardline, great luck on my part.

DSCN2158.jpg
1104 hits | 37.67 KB | Posted: 5/18/05
line measurement..

DSCN2159.jpg
1029 hits | 21.63 KB | Posted: 5/18/05
29"! I DOUBT these lines will be being stretched by any means

DSCN2160.jpg
1318 hits | 35.87 KB | Posted: 5/18/05
6" extended TTB line compared to the line on the 60..bit of difference

DSCN2178.jpg
1143 hits | 43.43 KB | Posted: 5/19/05
Cage Offroad Nitrogen Shocks, 14" travel.

DSCN2179.jpg
1151 hits | 43.05 KB | Posted: 5/19/05
Monroe Steering Stabalizer

DSCN2181.jpg
1023 hits | 24.27 KB | Posted: 5/19/05
Part #

DSCN2209.jpg
1165 hits | 42.52 KB | Posted: 6/6/05
WFO Concepts Steering

DSCN2213.jpg
1113 hits | 43.64 KB | Posted: 6/7/05
The wanker previous owner before me decided to put the drain plug in the center of the cover, which ...

DSCN2214.jpg
1089 hits | 39.79 KB | Posted: 6/7/05
weld er up

DSCN2215.jpg
1126 hits | 49.66 KB | Posted: 6/7/05
welded shut

DSCN2216.jpg
1159 hits | 59.54 KB | Posted: 6/7/05
grinded smooth

DSCN2241.JPG
1194 hits | 89.68 KB | Posted: 6/9/05

DSCN2257.jpg
1159 hits | 23.99 KB | Posted: 6/12/05

DSCN2258.jpg
1409 hits | 29.09 KB | Posted: 6/12/05
new power steering lines ran

DSCN2259.jpg
1857 hits | 23.34 KB | Posted: 6/12/05
power steering lines should tuck back above engine crossmmeber fine, i'll probably ziptie onto the t...

DSCN2260.jpg
1357 hits | 21.28 KB | Posted: 6/13/05

DSCN2261.jpg
1310 hits | 62.5 KB | Posted: 6/13/05