SuperMotors > 2006 Suzuki Hayabusa 1300 > open folder PPM Custom's Chrome Billet Hayabusa Gauge Bezel

[i]By Arthur Jensen[/i] [b]Blingin' Billet Bezel: We Install a PPM Custom's Chrome Billet 'Busa ...
Hits: 967
Size: 88.55 KB
Posted: 9/12/06
[i]By Arthur Jensen[/i] [b]Blingin' Billet Bezel: We Install a PPM Custom's Chrome Billet 'Busa ...		Start by removing the three Allen screws that hold the lower half of the inner fairing to the bike.
Hits: 557
Size: 74.29 KB
Posted: 9/12/06
Start by removing the three Allen screws that hold the lower half of the inner fairing to the bike.		Release the pins that hold the inner fairing to the windscreen supports by pushing in the center wit...
Hits: 553
Size: 73.56 KB
Posted: 9/12/06
Release the pins that hold the inner fairing to the windscreen supports by pushing in the center wit...		From the top, carefully pull the inner fairing away from the bike. The lower edge fits into the fra...
Hits: 544
Size: 85.43 KB
Posted: 9/12/06
From the top, carefully pull the inner fairing away from the bike. The lower edge fits into the fra...		The stock 'Busa bezel is held on with two Phillips screws along the bottom edge and double sided tap...
Hits: 609
Size: 105.17 KB
Posted: 9/12/06
The stock 'Busa bezel is held on with two Phillips screws along the bottom edge and double sided tap...
Since the bezel is still attached by the double-sided tape, you will have to pry it up carefully to ...
Hits: 683
Size: 99.25 KB
Posted: 9/12/06
Since the bezel is still attached by the double-sided tape, you will have to pry it up carefully to ...		Before mounting the PPM Custom billet bezel with the provided adhesive, set the new part in place to...
Hits: 1603
Size: 83.13 KB
Posted: 9/12/06
Before mounting the PPM Custom billet bezel with the provided adhesive, set the new part in place to...		To permanently mount the bezel, peel the cover-strips off the double-sided tape on the back of the P...
Hits: 639
Size: 90.58 KB
Posted: 9/12/06
To permanently mount the bezel, peel the cover-strips off the double-sided tape on the back of the P...		Once the screws are tight, install the new foam weather seal around the bottom and sides of the beze...
Hits: 594
Size: 80.96 KB
Posted: 9/12/06
Once the screws are tight, install the new foam weather seal around the bottom and sides of the beze...
Hits: 566
Size: 100.3 KB
Posted: 9/12/06
Next, install the inner fairing. Starting from the rear of the fairing pieces, work your way forward...
Hits: 644
Size: 101.14 KB
Posted: 9/12/06
Next, install the inner fairing. Starting from the rear of the fairing pieces, work your way forward...
Hits: 509
Size: 77 KB
Posted: 9/12/06
To install the pins that hold the inner fairing to the windscreen supports you must first reset them...
Hits: 1403
Size: 69.62 KB
Posted: 9/12/06
To install the pins that hold the inner fairing to the windscreen supports you must first reset them...		Now that the fairings are in place, tighten all three Allen screws.
Hits: 578
Size: 78.3 KB
Posted: 9/12/06
Now that the fairings are in place, tighten all three Allen screws.		Seen side-by-side, the stock and PPM bezel are quite a contrast. While the stock part’s faux-carb...
Hits: 1030
Size: 118.49 KB
Posted: 9/12/06
Seen side-by-side, the stock and PPM bezel are quite a contrast. While the stock part’s faux-carb...
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2009, LHB Companies LLC, DBA SuperMotors.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog