RecircLine.JPG 61 hits | 51.24 KB | Posted: 11/9/09 If MAX A/C only blows out the defrost registers, or if it switches to defrost during hard accelerati...
5.8L SPOUT.jpg 3228 hits | 48.98 KB | Posted: 10/2/04 SPOUT, cruise servo, test connectors on '93 5.8L.
EEC Install.JPG 2065 hits | 93.23 KB | Posted: 7/10/03 This is how I fit the '95 EEC into an '82 Bronco body tub. The black connector in the middle is the...
Dist-mount TFI-IV SPOUT.jpg 2604 hits | 42.61 KB | Posted: 10/1/05 DIstributor-mounted TFI-IV module & SPOUT connector on '84-91 trucks looking straight across the rad...
XTubeNew.JPG 1304 hits | 74.57 KB | Posted: 4/26/06 Crossover Tube for upstream secondary air on V8.
The foil-faced fabric on the L shields the HVAC vacuum reservoir on t...
5.8L TAD.jpg 1879 hits | 50.33 KB | Posted: 10/2/04 Thermactor Air Diverter valve & other components. The IAT/ACT is barely visible behind the fuel rai...
Filter86EFI.JPG 631 hits | 92.95 KB | Posted: 8/23/07 Early 5.0L EFI intake & air filter
See next image.
Intake86EFI.JPG 672 hits | 85.65 KB | Posted: 8/23/07 Early 5.0L EFI intake & air filter
See previous image.
InjectorBlower.JPG 562 hits | 77.42 KB | Posted: 7/23/07 Injector Blower used on '87-89 4.9L only. There's a small sensor clipped to the fuel rail that trig...
FanSw49L.JPG 377 hits | 72.67 KB | Posted: 4/12/08 Injector Cooling Fan Switch for '87-89 4.9L only
The length of the 4.9L I6 engine leaves VERY little room for an electric fan & shro...
ValleyGunk.JPG 2010 hits | 139.16 KB | Posted: 7/14/03 The inside of a '93 5.8L with ~140,000mi. The previous owner probably used Quaker State.
SenderOilPress.jpg 3164 hits | 33.27 KB | Posted: 1/15/06 Oil Pressure Sender
This is the NAPA number for the old-style oil pressure sender that is needed to...
Switch-SenderV8.JPG 19 hits | 74.2 KB | Posted: 11/15/09 On V8s, there's not enough room at the block for the sender, so a spacer is required, just like the ...
VacHoses94_58L.JPG 1025 hits | 39.76 KB | Posted: 8/24/06 The vacuum harness connector on the back of a '94 MAP 5.8L Bronco. The foreground is the vacuum tre...
For the operation of the 2ndry air system, see:
[url=http://www.supermotors...
02SmogPump.JPG 29 hits | 89.74 KB | Posted: 11/6/09 This is how to fix a seized air pump for nearly nothing:
1) break the three 10mm pulley bolts
2) r...
The Y wire ties into the auxilliary lighting circuit (Y and Bk/Y) at...
PCM Inside Text.JPG 1805 hits | 78.96 KB | Posted: 7/10/03 This is what my '83 kick looks like with the '95 computer mounted.
MCU83a.JPG 222 hits | 14.68 KB | Posted: 11/14/08 Rare location of early engine control computer above gas pedal. It's a cell phone pic, but it's the...
TransGaskets.jpg 81 hits | 59.71 KB | Posted: 10/15/09 Transmission Gasket ID
Click the pic to supersize.
CowlDrain.JPG 1541 hits | 70.25 KB | Posted: 7/10/03 This is where leaves build up, on both sides of the truck. The come thru the wiper valance slots ('...
Leaves.jpg 3065 hits | 74.76 KB | Posted: 7/10/03 This shows where leaves build up in '80-96 truck ductwork. If they build up around the resistors (g...
TempDoor.JPG 1241 hits | 78.58 KB | Posted: 7/10/03 This is looking rearward over the R wheelwell with the evaporator cover removed beside the R exhaust...
Wiper Valance 2.JPG 1123 hits | 116.24 KB | Posted: 7/10/03 This shows the differences in the '91 & '92 wiper valances. The '80-86 valance is just like the '87...
Jump Seats.JPG 1183 hits | 94.07 KB | Posted: 7/10/03 These jump seats are from a '78 Datsun/Nissan King Cab pickup, and they're easy to bolt onto any flo...
YorkSpeedoOil.jpg 1096 hits | 93.96 KB | Posted: 7/15/03 Speedometer Gear, York Compressor, & Oil Pressure Sender for V8
---------------------------------...
ACValves.JPG 135 hits | 70.58 KB | Posted: 4/17/09 A/C Vavles used on some '89-91 compressors. They should always be open (UNscrewed). To operate the...
Shocks.jpg 2795 hits | 67.58 KB | Posted: 7/10/03 These are the best shocks I've found for the money. ~$25/ea with a lifetime warranty. These 3 PNs ...
Shock Studs.jpg 1018 hits | 29.1 KB | Posted: 9/27/04 Front front shock studs, included in the CarQuest box.
Sway Bracket.jpg 704 hits | 71.93 KB | Posted: 8/16/03 Sway bar attached to valance
Spring Bushing Chisels.JPG 1059 hits | 74.03 KB | Posted: 7/10/03 After fighting this bushing, I figured out this method. Be careful removing the chisels - they FLY.
D50.JPG 1452 hits | 85.02 KB | Posted: 7/10/03 Dana 50IFS axles can be differentiated from D44IFSs by the "50" cast into the third member, and the ...
PressShafts.JPG 575 hits | 58.35 KB | Posted: 11/11/05 Pressing a U-joint out
Driveshafts BroncoE4OD.JPG 572 hits | 84.03 KB | Posted: 9/12/05 Driveshafts for a Bronco with E4OD & BW1356
Driveshafts.JPG 765 hits | 69.62 KB | Posted: 7/10/03 Front shafts are the same for all pickups & Broncos with the same transmission length. Rear shafts ...
Battery.JPG 1497 hits | 82.75 KB | Posted: 7/17/03 This is the best battery for the money. ~$80 with an 8-year warranty, the first 3 of which are free...
HomeLinkMemo.JPG 450 hits | 50.71 KB | Posted: 3/18/07 I haven't decided what to do with this yet, but it's interesting. I wanted to put it in the '75 Bro...
These are very rare, and I have yet to find one in working condition...
CB80.JPG 98 hits | 56.86 KB | Posted: 4/28/09 Factory CB in a 1980 Ranger F150 Trailer Special
If the buttons weren't missing from the handset,...
ReelLight1.JPG 1273 hits | 70.04 KB | Posted: 7/10/03 This light was used on '80-96 Ford trucks and some Jeep Cherokees (with a different connector). It ...
HoodTilt.jpg 1213 hits | 59.1 KB | Posted: 8/23/03 The metal bulb is the tilt switch, which contains a BB.
SteeringWheel 1.JPG 738 hits | 87.7 KB | Posted: 12/6/04 This is how the cruise button wires are connected on all pre-'93 trucks. The horn pad connector is ...
SteeringWheel 2.JPG 1036 hits | 76.25 KB | Posted: 12/6/04 A cheap puller makes the job easier, but the wheel can usually be removed by hooking your knees behi...
SteeringWheel 3.JPG 703 hits | 84.87 KB | Posted: 12/6/04 The white crescent-shaped turn signal cam commonly breaks, and you can see where I've spliced this o...
Turn Cam.JPG 1003 hits | 63.53 KB | Posted: 7/10/03 The bosses on the other side aren't molded right, so it doesn't return to center, and you have to be...
ClockSpringExploded.jpg 1416 hits | 26.35 KB | Posted: 12/2/05 Clock Spring ('94-up with driver's airbag) showing the film circuit which abrades & breaks over time...
IgnitionRodTilt.JPG 1273 hits | 82.91 KB | Posted: 7/10/03 This is the ignition pushrod in '92-96 tilt columns. It's the plastic gear rack. The L section of ...
Airbag.JPG 2013 hits | 84.02 KB | Posted: 7/10/03 This is the back of a '94-96 airbag, the same for most Ford cars & trucks.
Red: shaped charge
Yell...
MFSs.JPG 323 hits | 37 KB | Posted: 9/18/08 MultiFunction Switches used on '92-up Ford trucks, other Ford products, & other vehicles including t...
The pedal arm is simply pressed onto the splines of the shaft, a...
93SCDS.JPG 14 hits | 84.23 KB | Posted: 11/6/09 The SCDS was located here ONLY in '93 on trucks with cruise; older trucks used a mechanical vaccum v...
VSS 2.JPG 1331 hits | 90.41 KB | Posted: 7/10/03 This is the Vehicle Speed Sensor used on early (pre-'87) cruise systems. It's in the middle of the ...
Airbag Falsing Sensor.JPG 1398 hits | 56.45 KB | Posted: 11/25/05 Bronco airbag safing sensor at base of R B-pillar.
These slide-together relay sockets are from a cheap aftermarket alarm, but they can...
WCMs3.JPG 165 hits | 87.94 KB | Posted: 1/3/09 WIper Control Modules used from '92-up
I used to think they all took the same module, but the whi...
Body Mount Parts.JPG 1454 hits | 80.63 KB | Posted: 7/10/03 These are the basic parts of Ford truck body (cab, not bed) mounts.
94BodyLift.JPG 944 hits | 64.93 KB | Posted: 4/12/06 This truck was hit REALLY hard, but the body shouldn't have shifted THIS much.
94BodyMount.JPG 1220 hits | 67.67 KB | Posted: 4/12/06 Here's why the body slid off during the impact. Not only does it have a body lift - they used grade...
BatteryClamps.JPG 593 hits | 61.88 KB | Posted: 4/15/06 500A Battery Clamps from NAPA for $6.69/pack of 2. I'll be using one pair for a cheapo winch that p...
WSTool_.jpg 1029 hits | 34.04 KB | Posted: 5/12/07 This is a cheapo version of the tool, but it's effective.
WS_Tool1.jpg 446 hits | 44.73 KB | Posted: 5/12/07 The tool slips under the windshield trim. Slide it to hook the clips, beginning at a joint near a c...
WS_Tool4.jpg 408 hits | 65.73 KB | Posted: 5/12/07 Hold the tool at an angle so one point goes behind the clip.
WS_Tool5.jpg 396 hits | 41.95 KB | Posted: 5/12/07 Turn the tool to pry the clip slightly toward the center of the w/s, then lift the trim just enough ...
WS_Tool9.jpg 397 hits | 48.52 KB | Posted: 5/12/07 The lower trim clips are different, but they're released the same way.
These clips are no longer ...
WS_Tool7.jpg 624 hits | 45.25 KB | Posted: 5/12/07 The lower trim clips are different, but they're released the same way.
SwBrkts80-86.JPG 816 hits | 55.91 KB | Posted: 12/8/06 Type 1 ('80-86) Swingaway Brackets have sharply angled straight corners to match the older body. '8...
SwingawaySwap.JPG 91 hits | 65.79 KB | Posted: 4/27/09 Someone suggested that the curved body brackets of Type 2 & 3 swingaways wouldn't fit an '80-86 body...
SwingawayType2.JPG 600 hits | 68.93 KB | Posted: 7/23/07 Type 1 ('78~86) has a 2-screw notched strike for a teter-bar catch, a J-bolt mount, an UNreinforced ...
Tether.JPG 11 hits | 43.98 KB | Posted: 11/14/09 Swingaway Tether prevents quarter panel damage if the tire carrier is unlatched while driving, but d...
SnugLug.JPG 141 hits | 62.64 KB | Posted: 4/27/09 I could have installed this lug wrench carrier & tire lock (whose cover I had powdercoated at the sa...
Note that this truck also has the later-style windshield with the blackou...
SpoilerR.JPG 275 hits | 54.09 KB | Posted: 7/23/07 Aftermarket Rear Spoiler on an '80-91 Bronco
3BoltMirror.JPG 403 hits | 57.24 KB | Posted: 7/23/07 Rare 1980 3-bolt Hi-Low Mirror used on F250-350 only
BallPinConsole.JPG 334 hits | 71.91 KB | Posted: 7/23/07 Center Console with '78-80 ball-pin snaps instead of the more common '81-91 glove-box-style catch.
BW1356PTO.jpg 237 hits | 27.42 KB | Posted: 11/14/08 Rare PTO-style BW1356 from a diesel pickup. Note the front case half is aluminum on this version, w...
BW-1356 Slip.JPG 846 hits | 119 KB | Posted: 7/10/03 BW-1356 for F-series with mechanical shifter
Disco Fuel Pump.JPG 1074 hits | 77.37 KB | Posted: 8/6/03 Factory fuel pump access on a Land Rover Discovery.
3LDOHCtough.JPG 453 hits | 95.76 KB | Posted: 2/5/09 Oil pan & contents from a 3.0L DOHC Sable
Note the wear on the broken piston chunks - the engine ...
JackLR.JPG 42 hits | 65.11 KB | Posted: 8/22/09 Land Rover Bottle Jack used in Discovery, Discovery Series II, & pre-'03 Range Rover (Classic & New)...
LincolnLocker.JPG 35 hits | 73.46 KB | Posted: 8/29/09 A welded differential, commonly called a "Lincoln-locker" in reference to the popular brand of weldi...
FloorWiring93.JPG 9 hits | 53.61 KB | Posted: 11/15/09 Floor Wiring in a '93 EB Bronco
General Purpose Pics
