|
Hits: 8283 Size: 40.88 KB Posted: 4/6/06 $80 plus shipping by USPS Priority in the US from 38133. Each about 10" front-to-back and just... | Hits: 3383 Size: 49.27 KB Posted: 8/3/12 Access Plate Kit
Plate length (front-to-back) varies, but all are more than 3 ridges wide. This sh... | Hits: 3119 Size: 61.84 KB Posted: 8/2/12 Raw cover plates cut from my old '82 body tub.
I'll clean up the rough edges, drill the screw holes... | Hits: 6369 Size: 20.71 KB Posted: 4/5/06 Installation of fuel pump access hole cover panel. Before cutting, make sure your new cover plate w... | Hits: 8630 Size: 77.37 KB Posted: 8/6/03 Factory fuel pump access on a Land Rover Discovery & Discovery Series II. This is the idea behind t... |
Hits: 5245 Size: 77.21 KB Posted: 6/25/09 Because of my jump seats, it's easier for me to roll the floor cover from the front. But for most B... | Hits: 4769 Size: 54.53 KB Posted: 11/5/09 This '93EB was abaondoned for ~6 years, resulting in (among MANY other problems) a seized fuel pump. | Hits: 4882 Size: 71.65 KB Posted: 11/5/09 For most Broncos, like this stock '93EB, only the rear threshhold has to be removed to fold the carp... | Hits: 4998 Size: 80.18 KB Posted: 6/25/09 Since I applied anti-seize lube when I installed them years ago, these bolts are easy to remove now;... | Hits: 6427 Size: 68.77 KB Posted: 4/5/06 This procedure will make accessing the fuel pump or fuel level sender in any fullsize Bronco much ea... |
Hits: 6564 Size: 50.04 KB Posted: 4/5/06 Locate the line of spot welds holding the bed down on the body mount channel. The lip of the channe... | Hits: 6010 Size: 40.53 KB Posted: 4/5/06 This shows the welds' locations in relation to the lip of the channel. Cut behind this lip; the fro... | Hits: 6844 Size: 58.01 KB Posted: 4/5/06 The front of the hole (at the back of the channel's lip) should be no more than 26" forward fro... | Hits: 5099 Size: 68.71 KB Posted: 11/5/09 Find the line of spot welds, place the plate where it will go, then trace across its front & rear ed... | Hits: 5686 Size: 56.44 KB Posted: 4/5/06 A 4 1/2" angle grinder with a thin wheel is probably the easiest BUT MOST DANGEROUS way to make... |
Hits: 4675 Size: 76.57 KB Posted: 11/5/09 Sketch the cut line corners INSIDE the trace lines, and along the crease in the bottom of the channe... | Hits: 4441 Size: 50.46 KB Posted: 6/25/09 NOT following my own advice, I didn't trace the cover plate onto the floor first. This first hole i... | Hits: 4590 Size: 72.05 KB Posted: 11/5/09 The rear holes are noticeably closer to the gas tank than the front, so don't punch down when the dr... | Hits: 4458 Size: 51.49 KB Posted: 6/25/09 NOT following my own advice, I didn't trace the cover plate onto the floor first. The front L hole ... | Hits: 5582 Size: 70.42 KB Posted: 4/5/06 If you use a saw, make SURE you don't puncture the gas tank or cut the fuel lines & wires. Even if ... |
Hits: 4349 Size: 46.02 KB Posted: 6/25/09 Before ripping through the tank, I checked the depth against the fully-lowered blade. At the rear L... | Hits: 4375 Size: 74.74 KB Posted: 11/5/09 Be aware of the distance from the floor to the tank at all times, and remember that the fuel lines, ... | Hits: 4343 Size: 56.8 KB Posted: 6/25/09 The front edge has the most depth clearance for the tank & fuel lines, so I cut it 1st. The lip (vi... | Hits: 5623 Size: 47.68 KB Posted: 4/5/06 This is about where the hole should be. DO NOT CUT everything out like this pic shows - I'm harvest... | Hits: 6190 Size: 54.75 KB Posted: 4/5/06 This is where the hole should be. DO NOT CUT everything out like this pic shows - I'm harvesting th... |
Hits: 4338 Size: 52.91 KB Posted: 6/25/09 I tilted the jigsaw for the remaining 3 cuts to ensure I didn't puncture the tank below.
A slitting... | Hits: 360 Size: 53.92 KB Posted: 11/4/21 An air chisel is probably the quickest & safest way to cut the floor, because it doesn't risk damage... | Hits: 290 Size: 71.93 KB Posted: 11/4/21 An air chisel is probably the quickest & safest way to cut the floor, because it doesn't risk damage... | Hits: 259 Size: 83.49 KB Posted: 11/4/21 An air chisel is probably the quickest & safest way to cut the floor, because it doesn't risk damage... | Hits: 4744 Size: 58.51 KB Posted: 6/25/09 If you look closely in the shadow at the top, you'll see that I cut the vapor hose. Fortunately, it... |
Hits: 4124 Size: 51.08 KB Posted: 6/25/09 A quick way to make sure the plate will cover the hole. All the screw holes in the plate should be ... | Hits: 4761 Size: 69.11 KB Posted: 6/25/09 The lock ring is ~5" across, so a hole only 7" front-to-back is more than enough to work t... | Hits: 2932 Size: 94.34 KB Posted: 5/24/12 Even this is plenty of space to remove & install the pump, so don't cut a massive hole. Smaller is ... | Hits: 4622 Size: 71.95 KB Posted: 6/25/09 Tank Clearances for standard body mounts in good condition (these are Energy polyurethane). Collaps... | Hits: 4235 Size: 61.48 KB Posted: 6/25/09 After the repairs to the pump &/or sender, clean the floor around the hole, expose the sealant on th... |
Hits: 3820 Size: 61.91 KB Posted: 6/25/09 Along the front edge, the screw tips MAY contact the beam under the floor. To avoid this, position ... | Hits: 2854 Size: 95.58 KB Posted: 6/24/12 If the plate ever has to be removed again, remove all the screws & pry up the sealant. It's MUCH ea... | | | |