1994 Ford Bronco
Owner: Tom Bachant         (All of this user's registries on SuperMotors)
From: Ketchikan, AK, U.S.A.        (Other registries in AK)
Year, Make, & Model: 1994 Ford Bronco        (Other Ford Broncos)
Avatar:
Clubs: SuperFord.org        (Other vehicles in this club)
BigBroncos.com Registry        (Other vehicles in this club)
Nickname:
Mileage:
Engine: Stock 5.0 K&N Aircleaner
Drivetrain: Tranny: E4OD
Axles: D44IFS/Ford 8.8", 3.55 gears
Hubs: Stock Electric
Tires: 31x10.50 (so far)
Notes: Wish List:
6-8" lift
38" Tires
Lockers rear, ARB Front
Winch (Milemarker)
Lower Gears
Last Updated: 4/30/2002
Hits: 9193
Album
Folder Hits Comments Created Updated
folder Bronco Pics000006/29/036/29/03
    folder Stock Shots2002,20806/29/036/29/03
    folder Modification Begins80010,31706/29/036/29/03
Newest Media Files
lftside.JPG
1449 hits | 26.94 KB | Posted: 6/29/03

Here is a shot showing the whole left side. It doesn't look too bad so far. Both sides are trimmed. Now to figure out how I'll finish it.
cutoutright2.JPG
1405 hits | 22.73 KB | Posted: 6/29/03

Here is the right side fender cut out to the tape marking. You can just barely make out the inner fender. There is no turning back now.
tapedfender2.JPG
1276 hits | 28.67 KB | Posted: 6/29/03

Here is the left side taped for trimming. I had to use a slightly differant angle because of glare. Notice the hole near the front.
tapedfender.JPG
1296 hits | 29.01 KB | Posted: 6/29/03

Here is the left fender after taping. I have hopefully left enough meat fron and rear to bend it inward.
fendermarks.JPG
1329 hits | 29.21 KB | Posted: 6/29/03

Marking fenders for trimming.
fenderrust.JPG
1185 hits | 19.59 KB | Posted: 6/29/03

I thought I was just sanding off a few rust bubbles. As you can see I got rid of the rust. Now I have a hole.
installedguard.JPG
1154 hits | 22.29 KB | Posted: 6/29/03

Here is the Rock slider installed. The shot is take looking up at the drivers side.
rockbarhole.JPG
1223 hits | 25.92 KB | Posted: 6/29/03

Here is the 'Rock slider' that will reinforce my rocker panels. The cutout for the seatbelt bolt was done with an angle grinder. (Wife's Jeep in background)
broncorear.JPG
1100 hits | 18.56 KB | Posted: 6/29/03

Another shot of pre-modified Bronco.
Most Viewed Files
lftside.JPG
1449 hits | 26.94 KB | Posted: 6/29/03

Here is a shot showing the whole left side. It doesn't look too bad so far. Both sides are trimmed. Now to figure out how I'll finish it.
cutoutright2.JPG
1405 hits | 22.73 KB | Posted: 6/29/03

Here is the right side fender cut out to the tape marking. You can just barely make out the inner fender. There is no turning back now.
fendermarks.JPG
1329 hits | 29.21 KB | Posted: 6/29/03

Marking fenders for trimming.
tapedfender.JPG
1296 hits | 29.01 KB | Posted: 6/29/03

Here is the left fender after taping. I have hopefully left enough meat fron and rear to bend it inward.
tapedfender2.JPG
1276 hits | 28.67 KB | Posted: 6/29/03

Here is the left side taped for trimming. I had to use a slightly differant angle because of glare. Notice the hole near the front.
rockbarhole.JPG
1223 hits | 25.92 KB | Posted: 6/29/03

Here is the 'Rock slider' that will reinforce my rocker panels. The cutout for the seatbelt bolt was done with an angle grinder. (Wife's Jeep in background)
fenderrust.JPG
1185 hits | 19.59 KB | Posted: 6/29/03

I thought I was just sanding off a few rust bubbles. As you can see I got rid of the rust. Now I have a hole.
installedguard.JPG
1154 hits | 22.29 KB | Posted: 6/29/03

Here is the Rock slider installed. The shot is take looking up at the drivers side.
broncofront.JPG
1108 hits | 19.83 KB | Posted: 6/29/03

Here is my Bronco before any modifications.
Maintenance & Modification Logs
This user hasn't added any log entries, yet.
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2024 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog