whitebroncobumper.jpg
1357 hits | 30.64 KB | Posted: 6/30/03

Rear_Bumper.jpg
1871 hits | 10.88 KB | Posted: 6/30/03
Rear bumper design from Chris Chu

tire_carrier_rear_bumper.jpg
2020 hits | 39.81 KB | Posted: 6/30/03

rear_bumper_Crazed.jpg
1257 hits | 47.18 KB | Posted: 6/30/03
Rear bumper courtesy of Tim Crase

rear bumper.jpg
1236 hits | 28.86 KB | Posted: 8/27/03
Rear bumper designed by Dave Edwards High Desert OffRoad out of Oregon, my final bumper will have a ...

Dcp00851.jpg
1086 hits | 79.42 KB | Posted: 1/10/04
My new heavy duty rear bumper from Dave Edwards, High Desert Off Road.

Dcp00852.jpg
1156 hits | 82 KB | Posted: 1/10/04
The new bumper has a receiver hitch, to d-ring mounts, and and antenna mount.

Dcp00859.jpg
990 hits | 93.72 KB | Posted: 1/10/04
The old stump anchor removed.

Dcp00858.jpg
1004 hits | 67.97 KB | Posted: 1/10/04
Old bumper removed.

Dcp00864.jpg
1085 hits | 103.51 KB | Posted: 1/10/04
Getting ready to test fit the rear bumper, this is a better shot.

Dcp00865.jpg
990 hits | 91.61 KB | Posted: 1/10/04
This is the test fitting of the bumper before I made the first cut off the mounts.

Dcp00860.jpg
1000 hits | 87.39 KB | Posted: 1/10/04
The new mounting bolts I'm using are on the left versus the old ones, these are 5/8th inch thick wit...

Dcp00868.jpg
942 hits | 98.29 KB | Posted: 1/10/04
Here's where I screwed up, I should not have cut these down...

Dcp00871.jpg
1052 hits | 96.76 KB | Posted: 1/10/04
Here it is after I cut the mounts down, looks like it should fit right?? Wrong, it's having clearanc...

Dcp00886.jpg
963 hits | 80.17 KB | Posted: 1/12/04
Here you can see the screw up. I cut too much off.

bumper.jpg
1035 hits | 56.79 KB | Posted: 1/22/04
Here is the bumper after I had the patches welded on, this were necessary to offset the height of th...

Dcp00915.jpg
1070 hits | 79.93 KB | Posted: 1/23/04
Jacking the bumper with the new mounts into place.

Dcp00916.jpg
1019 hits | 86.75 KB | Posted: 1/23/04
Almost there. Getting the holes lined up for the bolts.

Dcp00921.jpg
1021 hits | 80.45 KB | Posted: 1/23/04
These are the grad 8 bolts used to hold it on, I may still drill another hole for a 3rd bolt but thi...

Dcp00917.jpg
1560 hits | 67.72 KB | Posted: 1/23/04
It's bolted on, even though it was dark, I could not wait to take pics.

Dcp00918.jpg
1035 hits | 86.07 KB | Posted: 1/23/04
Here is another angle.

Dcp00919.jpg
1034 hits | 87.73 KB | Posted: 1/23/04
Clearance from the bumper to the tire carrier now.

Dcp00922.jpg
1027 hits | 80.71 KB | Posted: 1/23/04
The tire carrier shut. The bumper looks great, can't wait to try it out.

patch.jpg
975 hits | 40.76 KB | Posted: 1/23/04