Sixlitre > 1986 Ford Bronco > open folder Saginaw II (replacement)

Even the best breaks eventually. I'd been trying to trace the belt squeal for about 6 months. Even...
IMG_0001.JPG
982 hits | 67.18 KB | Posted: 1/14/05
Even the best breaks eventually. I'd been trying to trace the belt squeal for about 6 months. Even...
Got another remanufactured Cardone Saginaw for "my 78 Ford Econoline van" for cheap enough to replac...
IMG_0083.JPG
913 hits | 47.26 KB | Posted: 1/14/05
Got another remanufactured Cardone Saginaw for "my 78 Ford Econoline van" for cheap enough to replac...
Started by undoing the low pressure return line's hose clamp, visible on hose.
IMG_0005.JPG
1004 hits | 75.49 KB | Posted: 1/14/05
Started by undoing the low pressure return line's hose clamp, visible on hose.
Slacking off this half inch cooler pipe retaining clamp bolt helps get the hoses off and on. Just re...
IMG_0009.JPG
898 hits | 59.41 KB | Posted: 1/14/05
Slacking off this half inch cooler pipe retaining clamp bolt helps get the hoses off and on. Just re...
I wanted to flush my old fluid out, even though it was clean to look at I'm sure there were filings ...
IMG_0013.JPG
877 hits | 51.3 KB | Posted: 1/14/05
I wanted to flush my old fluid out, even though it was clean to look at I'm sure there were filings ...
Next, before you slack any mounting bolts, crack loose the high pressure hose fitting. It's easier n...
IMG_0019.JPG
853 hits | 56.76 KB | Posted: 1/14/05
Next, before you slack any mounting bolts, crack loose the high pressure hose fitting. It's easier n...
Then just loosen off and whip out the two mounting bolts.
IMG_0021.JPG
901 hits | 42.42 KB | Posted: 1/14/05
Then just loosen off and whip out the two mounting bolts.
Off comes the belt and out comes the pump, leaking and spilling all over the place.
IMG_0022.JPG
873 hits | 65.52 KB | Posted: 1/14/05
Off comes the belt and out comes the pump, leaking and spilling all over the place.
Clamped her into the vice so it's easier to work on.
IMG_0031.JPG
848 hits | 66.01 KB | Posted: 1/14/05
Clamped her into the vice so it's easier to work on.
A little of your favourite penetrating oil onto the shaft will help the pulley come off more easily...
IMG_0034.JPG
875 hits | 64.13 KB | Posted: 1/14/05
A little of your favourite penetrating oil onto the shaft will help the pulley come off more easily...
Borrowed a PS pulley puller tool kit from a local jobber to re and re the pulley without damaging th...
IMG_0029.JPG
909 hits | 57.31 KB | Posted: 1/14/05
Borrowed a PS pulley puller tool kit from a local jobber to re and re the pulley without damaging th...
Why use a ractchet when a two foot flex bar can do the job so much more easily, and they wonder how ...
IMG_0040.JPG
904 hits | 69.81 KB | Posted: 1/14/05
Why use a ractchet when a two foot flex bar can do the job so much more easily, and they wonder how ...
Now just undo the bolts and stud and transfer the bracket onto the remanufactured Saginaw.
IMG_0043.JPG
850 hits | 68.21 KB | Posted: 1/14/05
Now just undo the bolts and stud and transfer the bracket onto the remanufactured Saginaw.
Mine had one stud on the back of the pump to hold the 78 van bracket on with a nut.
IMG_0046.JPG
823 hits | 54.91 KB | Posted: 1/14/05
Mine had one stud on the back of the pump to hold the 78 van bracket on with a nut.
A little synthetic grease onto the shaft to help the pulley slide/pull on.
IMG_0049.JPG
887 hits | 59.64 KB | Posted: 1/14/05
A little synthetic grease onto the shaft to help the pulley slide/pull on.
The pulley puller also installs the pulley onto the new pump shaft very well, by tightening it up un...
IMG_0051.JPG
981 hits | 74.74 KB | Posted: 1/14/05
The pulley puller also installs the pulley onto the new pump shaft very well, by tightening it up un...
I choose to put the new low pressure hose on now, while it's on the bench and easy to tighten the tw...
IMG_0054.JPG
806 hits | 49.65 KB | Posted: 1/14/05
I choose to put the new low pressure hose on now, while it's on the bench and easy to tighten the tw...
To flush the pump I've already added that clear hose to the low pressure return pipe of the cooler a...
IMG_0065.JPG
848 hits | 53.1 KB | Posted: 1/14/05
To flush the pump I've already added that clear hose to the low pressure return pipe of the cooler a...
I had been using the synthetic stuff on the right, but I'm going to flush it out and use the regular...
IMG_0085.JPG
907 hits | 64.13 KB | Posted: 1/14/05
I had been using the synthetic stuff on the right, but I'm going to flush it out and use the regular...
There's my new canned ham all bolted up in place and filled up with fluid ready to flush through.
IMG_0078.JPG
1071 hits | 75.28 KB | Posted: 1/14/05
There's my new canned ham all bolted up in place and filled up with fluid ready to flush through.
Now that the flushing is done I removed the clear hose and installed the new PS hose with two oppose...
IMG_0070.JPG
856 hits | 46.69 KB | Posted: 1/14/05
Now that the flushing is done I removed the clear hose and installed the new PS hose with two oppose...