Sixlitre > 1986 Ford Bronco > open folder Fan Install Day

Here's one of the slots cut in the lower fan support to accept the tab on the bottom of the angle ir...
IMG_0087.JPG
1165 hits | 67.01 KB | Posted: 6/19/05
Here's one of the slots cut in the lower fan support to accept the tab on the bottom of the angle ir...
Here's the MaxiFuse holder with the copper eyelets soldered onto the 6 gauge wires and heat shrink o...
IMG_0091.JPG
1155 hits | 43.77 KB | Posted: 6/19/05
Here's the MaxiFuse holder with the copper eyelets soldered onto the 6 gauge wires and heat shrink o...
Here's the connection to the right (supply side) of the MegaFuse. It's the 6 gauge in total red. The...
IMG_0130.JPG
1263 hits | 90.91 KB | Posted: 6/19/05
Here's the connection to the right (supply side) of the MegaFuse. It's the 6 gauge in total red. The...
You can make out the empty MaxiFuse holder for the fan supply just above the rad, tucked under the o...
IMG_0124.JPG
1161 hits | 70.9 KB | Posted: 6/19/05
You can make out the empty MaxiFuse holder for the fan supply just above the rad, tucked under the o...
Stuffing the relay sockets on the adjustable controller full of dielectric grease. Great shot of adj...
IMG_0118.JPG
1140 hits | 54.56 KB | Posted: 6/19/05
Stuffing the relay sockets on the adjustable controller full of dielectric grease. Great shot of adj...
Relay for adjustable controller being pressed in.
IMG_0119.JPG
1015 hits | 51.65 KB | Posted: 6/19/05
Relay for adjustable controller being pressed in.
I cut and lengthened the supplied wet sensor's wires to reach the T-stat housing, which has a thread...
IMG_0141.JPG
1245 hits | 44.42 KB | Posted: 6/19/05
I cut and lengthened the supplied wet sensor's wires to reach the T-stat housing, which has a thread...
Here's where the sensor will thread into.
IMG_0142.JPG
1034 hits | 69.09 KB | Posted: 6/19/05
Here's where the sensor will thread into.
Here's the the quick disconnect all together and stuffed full of dielectric grease. The sensor, behi...
IMG_0148.JPG
1309 hits | 74.7 KB | Posted: 6/19/05
Here's the the quick disconnect all together and stuffed full of dielectric grease. The sensor, behi...
You can just make out one of only two self tapping bolts that hold the framework in place. Note that...
IMG_0127.JPG
1068 hits | 67.85 KB | Posted: 6/19/05
You can just make out one of only two self tapping bolts that hold the framework in place. Note that...
All this time there has been clearance enough, on an 80-86, to try the new fan, with the old one sti...
IMG_0110.JPG
1043 hits | 60.96 KB | Posted: 6/19/05
All this time there has been clearance enough, on an 80-86, to try the new fan, with the old one sti...
I bought shorter 5/16" UNF-24 (fine thread) bolts to allow for the fan, with it's thick mounting fla...
IMG_0112.JPG
1018 hits | 41.38 KB | Posted: 6/19/05
I bought shorter 5/16" UNF-24 (fine thread) bolts to allow for the fan, with it's thick mounting fla...
Called it right as you can see these have plenty of shaft to hold the threads but won't stick in too...
IMG_0115.JPG
1065 hits | 57.91 KB | Posted: 6/19/05
Called it right as you can see these have plenty of shaft to hold the threads but won't stick in too...
Here's a pic with descriptions of the components
Finished fan.JPG
1458 hits | 74.17 KB | Posted: 6/19/05
Here's a pic with descriptions of the components
Test diagram
fan diagram.jpg
1528 hits | 32.88 KB | Posted: 6/21/05
Test diagram