IMG_0398.JPG
1003 hits | 84.6 KB | Posted: 4/15/07
Old tank out and into the wheelbarrow

IMG_0400.JPG
1097 hits | 73.42 KB | Posted: 4/15/07
The vent hose within the filler hose

IMG_0395.JPG
910 hits | 63.01 KB | Posted: 4/15/07
Ugly looking 86' in-tank fuel pump/sending unit. It's older than the old tank, which I stuck in new ...

IMG_0402.JPG
943 hits | 49.56 KB | Posted: 4/15/07
The vent valve popped out very easily (Thank goodness). So many people bust these things removing th...

IMG_0407.JPG
923 hits | 47.13 KB | Posted: 4/15/07
Got her out intact ! Whew !

IMG_0412.JPG
852 hits | 46.59 KB | Posted: 4/15/07
Hope I can find a new filter screen !

IMG_0413.JPG
973 hits | 43.95 KB | Posted: 4/15/07
When I finally got the plug off the sending unit I found one of the three socket terminal clips had ...

IMG_0404.JPG
965 hits | 87.19 KB | Posted: 4/15/07
Only 8 years old and this tank is toast ! Gonna do some coating on the new tank so I'm not in the sa...

IMG_0407.JPG
953 hits | 47.13 KB | Posted: 4/19/07
The 86's have the in-tank pump "AND" the gauge sender unit on the same stalk and their plug/harness ...

IMG_0420.JPG
887 hits | 36.5 KB | Posted: 4/19/07
Couldn't find a new plug, so I drilled out the busted terminal and install another.

IMG_0436.JPG
869 hits | 36.68 KB | Posted: 4/19/07
For around a buck I got a whole package of these handy dandy little terminals. Not an exact fit, but...

IMG_0421.JPG
846 hits | 33.17 KB | Posted: 4/19/07
The ground wire now sticks out the back on this McGuyver'd plug

IMG_0429.JPG
888 hits | 46.82 KB | Posted: 4/19/07
I whittled the back of the plug out to semi-recess the wire into the plug a bit and make it easier t...

IMG_0431.JPG
939 hits | 58.73 KB | Posted: 4/19/07
Because of the corrosion up here I even lubed the soldered joints with dielectric grease before I he...

IMG_0444.JPG
906 hits | 44.22 KB | Posted: 4/19/07
A little automotive Goop keeps it in place and weatherproofs it nicely.

IMG_0455.JPG
1006 hits | 46.39 KB | Posted: 4/19/07
Beautiful new Canadian made steel tank for $130.00 CDN. How do they do it ! Note the smaller 2" open...

IMG_0441.JPG
904 hits | 48.05 KB | Posted: 4/19/07
After cleaning the packing grease and residue off the tank with acetone, I emptied two of these spra...

IMG_0462.JPG
968 hits | 61.92 KB | Posted: 4/19/07
Beat the dents(left of tape measure) flat with a small sledge. Ground enough rust off the saddle poi...

IMG_0451.JPG
1132 hits | 73.47 KB | Posted: 4/19/07
Steve83 suggested using camper top foam backed tape and I'd say he was right on the money. Works gre...

IMG_0465.JPG
1109 hits | 39.27 KB | Posted: 4/19/07
I even stuck an extra layer of the foam tape right onto the tank's saddle points for double protecti...

IMG_0472.JPG
1134 hits | 62.35 KB | Posted: 4/19/07
There's my favourite anti-rust grease in action(painted the floor above the tank while it was out to...

IMG_0477.JPG
1079 hits | 51.58 KB | Posted: 4/19/07
The vent valve going back in. Be sure to install the rubber grommet first and then the valve.

IMG_0483.JPG
1163 hits | 48.34 KB | Posted: 4/19/07
Note the orange O-ring on the R/H nipple. For better or for worse these 86 connectors use the same c...

IMG_0886.JPG
1427 hits | 52.81 KB | Posted: 4/19/07
There it all is, tank in the skidplate, ready for me to do my bench pressing impression. Note the sp...

IMG_0488.JPG
1155 hits | 41.44 KB | Posted: 4/20/07
All done. Six coats of clear urethane for protection. Hooked up the lines, stuck in the filler neck ...