|
|
Hits: 63
Size: 51.15 KB
Posted: 7/13/20
20200710 - Pulled the rear seat out. Lot's of space... having trouble unbolting the three mounts fro... | 
Hits: 102
Size: 66.08 KB
Posted: 7/16/20
20200715 - Passenger seat came out surprisingly easy. Unplug the cable connecting to the bottom, the... | 
Hits: 52
Size: 70.48 KB
Posted: 7/16/20
20200715 - Center console comes out with three 10mm bolts. It also came out pretty easily. | 
Hits: 62
Size: 54.82 KB
Posted: 7/16/20
20200715 - Driver's seat came out tough. I ended up shearing off two of the four 15mm bolts getting ... | 
Hits: 52
Size: 59.69 KB
Posted: 7/16/20
20200716 - Pretty spacious without seats. This is going to require a lot of sound deadening material... |
Hits: 52
Size: 33.01 KB
Posted: 7/16/20
20200715 - All of the rest of the interior is more or less layered over the top of each other, and n... | 
Hits: 47
Size: 39.84 KB
Posted: 7/16/20
20200715 - Next is the long piece that runs along the bottom of the hard-top window. It's secured by... | 
Hits: 69
Size: 34.85 KB
Posted: 7/16/20
20200715 - This is what the trim clips are hooking into to hold the trim below the hard-top window. ... | 
Hits: 54
Size: 40.45 KB
Posted: 7/16/20
20200715 - The next piece I removed was this trim piece at the back of the hard top running vertical... | 
Hits: 46
Size: 51.54 KB
Posted: 7/16/20
20200715 - Next is the trim over the front driver and passenger windows (3-4 screws each) followed b... |
Hits: 55
Size: 27.39 KB
Posted: 7/16/20
20200715 - The seatbelt needs to come off for the B pillar trim to come out. It requires a t50 torx ... | 
Hits: 45
Size: 69.34 KB
Posted: 7/16/20
20200715 - Passenger seatbelt top bolt removed. It has some carpet-padding-like material between the... | 
Hits: 50
Size: 58.03 KB
Posted: 7/16/20
20200715 - Made some pretty good progress. I have quite a bit more to go, though. | 
Hits: 48
Size: 36.93 KB
Posted: 7/16/20
20200715 - The B pillar looks like it has dirty water streaks from the seam. | 
Hits: 47
Size: 21.09 KB
Posted: 7/16/20
20200715 - Passnger B pillar seam shows evidence of leaking. |
Hits: 54
Size: 29.08 KB
Posted: 7/16/20
20200715 - Driver B pillar seam shows evidence of leaking. Also, the gap in the seam is much bigger ... | 
Hits: 58
Size: 28.4 KB
Posted: 7/18/20
20200718 - The rear seat belts will have to come out completely since I can't get the side trim off ... | 
Hits: 56
Size: 33.11 KB
Posted: 7/18/20
20200718 - With the seatbelt bolts removed, the side trim can be easily removed. Be aware there is a... | 
Hits: 49
Size: 37.76 KB
Posted: 7/18/20
20200718 - One of the three T50 torx bits I broke trying to get the driver side bed bolt out. | 
Hits: 48
Size: 56.38 KB
Posted: 7/18/20
20200718 - After getting the carpets out, there was just a lot of vacuuming and wiping down to do. 2... |
Hits: 45
Size: 65.34 KB
Posted: 7/18/20
20200718 - Progression of cleaning, laying out the first stage of sound deadening (CLD tiles), and a... | 
Hits: 46
Size: 66.43 KB
Posted: 7/18/20
20200718 - Progression of cleaning, laying out the first stage of sound deadening (CLD tiles), and a... | 
Hits: 52
Size: 77.03 KB
Posted: 7/18/20
20200718 - Progression of cleaning, laying out the first stage of sound deadening (CLD tiles), and a... | 
Hits: 45
Size: 75.12 KB
Posted: 7/18/20
20200718 - Progression of cleaning, laying out the first stage of sound deadening (CLD tiles), and a... | 
Hits: 51
Size: 73.98 KB
Posted: 7/18/20
20200718 - Progression of cleaning, laying out the first stage of sound deadening (CLD tiles), and a... |
Hits: 64
Size: 72.67 KB
Posted: 7/18/20
20200718 - Progression of cleaning, laying out the first stage of sound deadening (CLD tiles), and a... | 
Hits: 50
Size: 63.89 KB
Posted: 7/18/20
20200718 - Progression in the front of cleaning, laying out the first stage of sound deadening (CLD ... | 
Hits: 57
Size: 58.17 KB
Posted: 7/18/20
20200718 - Progression in the front of cleaning, laying out the first stage of sound deadening (CLD ... | 
Hits: 62
Size: 64.42 KB
Posted: 7/19/20
20200719 - Pulled the headliner off so I could get the roof done. These visors are a pain in the ass... | 
Hits: 46
Size: 52.46 KB
Posted: 7/19/20
20200719 - The visors notch into this hole and twist to more or less lock them in place on top of th... |
Hits: 49
Size: 56.08 KB
Posted: 7/19/20
20200719 - You can see the bit that notches into the roof and the spring assembly that goes into the... | 
Hits: 51
Size: 41.26 KB
Posted: 7/19/20
20200719 - The headliner is held up by the center console, a plastic trim clip, one over the driver ... | 
Hits: 51
Size: 50.13 KB
Posted: 7/19/20
20200719 - I cleaned the roof and applied the CLD tiles. | 
Hits: 54
Size: 47.69 KB
Posted: 7/19/20
20200719 - Used 3m spray high strength 90 spray cement on this Hydrophobic Melamine Foam (HMF) as th... | 
Hits: 69
Size: 71.42 KB
Posted: 7/19/20
20200719 - Putting the headliner back up by yourself is kind of tough. Getting it aligned with the H... |
Hits: 54
Size: 42 KB
Posted: 7/19/20
20200719 - It was 105 degrees today so I had to quit after trimming up this first piece. Lots of pla... | 
Hits: 48
Size: 47.18 KB
Posted: 8/15/20
20200815 - Reinstalled the front trim at the top of the windshield. I put a bit of HMF on the back t... | 
Hits: 45
Size: 54.47 KB
Posted: 8/15/20
20200815 - Started fitting MLV in the cargo area driver wheel well. | 
Hits: 54
Size: 40.01 KB
Posted: 8/15/20
20200815 - Started cementing the MLV in the cargo area driver wheel well. | 
Hits: 51
Size: 35.85 KB
Posted: 8/15/20
20200815 - Started cementing the MLV in the cargo area driver wheel well. |
Hits: 44
Size: 39.24 KB
Posted: 8/15/20
20200815 - Cementing CCF to the MLV in the inner quarter panel | 
Hits: 46
Size: 38.29 KB
Posted: 8/15/20
20200815 - Cementing the MLV in the inner quarter panel | 
Hits: 42
Size: 65.55 KB
Posted: 8/15/20
20200815 - Cementing the MLV in the inner quarter panel | 
Hits: 49
Size: 32.35 KB
Posted: 8/15/20
20200815 - Cementing the HMF in the inner quarter panel | 
Hits: 45
Size: 56.18 KB
Posted: 8/15/20
20200815 - Cementing the MLV in the inner quarter panel |
Hits: 50
Size: 55.28 KB
Posted: 8/15/20
20200815 - More MLV and CCF on the cargo floor. | 
Hits: 54
Size: 41.43 KB
Posted: 8/16/20
20200816 - Started putting down MLV and CCF on the passenger side quarter and wheel well. | 
Hits: 54
Size: 40.97 KB
Posted: 8/16/20
20200816 - Started putting down MLV and CCF on the passenger side quarter and wheel well. | 
Hits: 43
Size: 73.8 KB
Posted: 8/16/20
20200816 - Replacing the 6 rear seat bolts with grade 8 stainless. | 
Hits: 43
Size: 59.76 KB
Posted: 8/16/20
|
Hits: 42
Size: 52.74 KB
Posted: 8/16/20
20200816 - Drilled through the sound deadening to place the bolts. Half of them won't thread and I'm... | 
Hits: 46
Size: 66.67 KB
Posted: 8/16/20
20200816 - Foam on the rear speakers disintegrated, so I replaced it with CCF. | 
Hits: 47
Size: 54.1 KB
Posted: 8/16/20
20200816 - Passenger side is complete. Time for new flooring and putting the trim back on. | 
Hits: 45
Size: 42.99 KB
Posted: 8/16/20
20200816 - Passenger side wheel well vinyl placed. Might need to heatgun it to get it to lay out fla... | 
Hits: 44
Size: 49.18 KB
Posted: 8/20/20
20200818 - Finished up CCF and MLV on the driver side cargo area. |
Hits: 46
Size: 42.33 KB
Posted: 8/20/20
20200818 - And HMF on the driver side cargo area. | 
Hits: 51
Size: 53.02 KB
Posted: 8/20/20
20200818 - Cargo area sound deadening is finished. | 
Hits: 54
Size: 51.88 KB
Posted: 8/20/20
20200820 - I started applying the new vinyl flooring I purchased from Bronco Graveyard (been sitting... | 
Hits: 54
Size: 48.48 KB
Posted: 8/23/20
20200821 - Started laying CCF and MLV in the cabin area. | 
Hits: 43
Size: 58.21 KB
Posted: 8/23/20
20200821 - Needed heavy boxes to keep the MLV down on the bit that attached the cargo area to the ca... |
Hits: 50
Size: 50.86 KB
Posted: 8/23/20
20200821 - Needed heavy boxes to keep the MLV down on the bit that attached the cargo area to the ca... | 
Hits: 47
Size: 47.49 KB
Posted: 8/23/20
20200821 - Used industrial velcro to keep the MLV tight to the dropoff from the cargo area and help ... | 
Hits: 53
Size: 52.38 KB
Posted: 8/23/20
20200821 - Much easier to drill holes and cut holes through the CCF and vinyl one layer at a time, r... | 
Hits: 47
Size: 56.2 KB
Posted: 8/23/20
20200821 - More CCF down for the rest of the floor in the cabin. | 
Hits: 40
Size: 48.57 KB
Posted: 8/23/20
20200821 - Putting MLV on this one elevated place under the center console took forever. Lots of cut... |
Hits: 43
Size: 88.68 KB
Posted: 8/23/20
20200822 - These instructions are bull. I did this and it still doesn't form correctly. Heat gun was... | 
Hits: 46
Size: 35.09 KB
Posted: 8/23/20
20200822 - Finally finished the transmission hump | 
Hits: 51
Size: 55.27 KB
Posted: 8/23/20
20200822 - Second view of the finished transmission hump. Lot's of velcro used here to keep the cont... | 
Hits: 109
Size: 52.36 KB
Posted: 8/23/20
20200822 - I had excess CCF, so I put it over the top of the sound deadening vinyl, and under the fl... | 
Hits: 57
Size: 73.5 KB
Posted: 8/23/20
20200822 - Starting to reinstall some trim. I had to install and uninstall several times to perfect ... |
Hits: 48
Size: 66.54 KB
Posted: 8/23/20
20200822 - Padding removed from behind the pocket on the side panel. | 
Hits: 53
Size: 58.4 KB
Posted: 8/23/20
20200822 - Also reinstalled the mounts for the rear seat amongst this disaster of tools and things. | 
Hits: 56
Size: 54.2 KB
Posted: 8/23/20
20200822 - Completed reinstalling some trim and mounts in the cargo area. | 
Hits: 44
Size: 56.76 KB
Posted: 8/23/20
20200822 - Padding came with the cabin flooring, so I positioned and trimmed it as necessary and use... | 
Hits: 52
Size: 53.25 KB
Posted: 8/23/20
20200822 - The front flooring required a massive amount of trimming, refuses to let me get the creas... |
Hits: 114
Size: 48.6 KB
Posted: 8/23/20
20200822 - Preview of my struggles getting the F250 reupholstered 40/20/40 seats and seatbelts in. I... | 
Hits: 51
Size: 44.46 KB
Posted: 8/23/20
20200823 - After a metric F***load of finagling and forcing, I was able to get the seats to bolt up ... | 
Hits: 51
Size: 57.62 KB
Posted: 8/23/20
20200823 - I still have more heatgun treatments to do on the floor, more trimming to do, and some mo... | | |
Sound Deadening & Flooring