np205q.JPG
3526 hits | 39.1 KB | Posted: 3/9/08
other than some spot painting, its ready to install into the truck
(Posted in: np205/twin-stick)

delete.panel03.jpg
634 hits | 58.15 KB | Posted: 5/19/08
(Posted in: Tail light relocate)

delete.panel05.jpg
687 hits | 57.42 KB | Posted: 5/19/08
(Posted in: Tail light relocate)

delete.panel06.jpg
642 hits | 61.7 KB | Posted: 5/19/08
(Posted in: Tail light relocate)

MVC-446S.JPG
684 hits | 32.8 KB | Posted: 9/20/08
delete.panel painted
(Posted in: Tail light relocate)

paint08.JPG
595 hits | 78.9 KB | Posted: 5/27/08
painting the rig with KEM 400 from sherwin-williams
(Posted in: Paint Job)

paint17.JPG
805 hits | 107.13 KB | Posted: 5/27/08
fresh paint. that paint really lays down good and is really easy to work with
(Posted in: Paint Job)

paint02.JPG
733 hits | 77.02 KB | Posted: 7/1/08
(Posted in: Paint Job)

paintprep03.jpg
670 hits | 69.6 KB | Posted: 7/1/08
(Posted in: Paint Job)

paintprep22.jpg
641 hits | 68.57 KB | Posted: 7/1/08
(Posted in: Paint Job)

paintprep08.jpg
674 hits | 75 KB | Posted: 7/1/08
(Posted in: Paint Job)

paint13.JPG
680 hits | 62.44 KB | Posted: 7/1/08
(Posted in: Paint Job)

paint10.JPG
735 hits | 76.3 KB | Posted: 7/1/08
(Posted in: Paint Job)

paint06.JPG
680 hits | 79.34 KB | Posted: 7/1/08
(Posted in: Paint Job)

Picture or Video 005.jpg
631 hits | 39.37 KB | Posted: 9/29/08
(Posted in: bed armor)

Picture or Video 004.jpg
640 hits | 42.22 KB | Posted: 9/29/08
(Posted in: bed armor)

yoke02.JPG
639 hits | 42.14 KB | Posted: 10/15/08
Original yoke. weak design. this one broke 3 of 4 corners
(Posted in: Rear output upgrade)

dshaft-flange013.JPG
652 hits | 55.91 KB | Posted: 10/15/08
flange with new u-joint installed on d-shaft
(Posted in: Rear output upgrade)

flange02.JPG
973 hits | 28.13 KB | Posted: 10/15/08
kit from Advanced Adapters.
pt # AF1300
(Posted in: Rear output upgrade)

dshaft-flange11.JPG
910 hits | 42.2 KB | Posted: 10/15/08
adapter with new nut, torqued to spec.
(Posted in: Rear output upgrade)

dshaft-flange10.JPG
906 hits | 35.98 KB | Posted: 10/15/08
adapter installed, note rubber gasket for splines
(Posted in: Rear output upgrade)

dshaft-flange08.JPG
1072 hits | 44.46 KB | Posted: 10/15/08
NP205 with seal removed
(Posted in: Rear output upgrade)

dshaft-flange05.JPG
938 hits | 23.78 KB | Posted: 10/15/08
adapter w/ flange mate
(Posted in: Rear output upgrade)

hd.d44a.JPG
742 hits | 34.12 KB | Posted: 1/28/09
a pair of HD dana44's i picked up to swap the front end so i have 8 lug wheels
(Posted in: my rear end)

MVC-553S.JPG
776 hits | 29.77 KB | Posted: 1/28/09
ruff stuff brake brackets for the rear 14bff brake swap
(Posted in: my rear end)

MVC-541S.JPG
1224 hits | 38.35 KB | Posted: 1/28/09
14 bolt full-floater rear diff. 3/4 ton version
(Posted in: my rear end)

14bdisk04.JPG
690 hits | 38.09 KB | Posted: 2/9/09
ruff stuff caliper bracket installed
(Posted in: my rear end)

14bdisk06.JPG
842 hits | 40.62 KB | Posted: 2/9/09
14bff rotor and hub instarlled
(Posted in: my rear end)

14bdisk07.JPG
679 hits | 40.82 KB | Posted: 2/9/09
disk brakes installed on brackets
(Posted in: my rear end)

14bdisk01.JPG
726 hits | 35.5 KB | Posted: 2/9/09
14bff bare spindle
(Posted in: my rear end)

14bdisk03.JPG
748 hits | 31.38 KB | Posted: 2/9/09
hub seperated from drum
(Posted in: my rear end)

d44_build02.JPG
824 hits | 34.51 KB | Posted: 2/9/09
danna 44 from axel ready to be built
(Posted in: my rear end)

eldo.calipers.JPG
1049 hits | 31.93 KB | Posted: 7/4/09
a set of used Cadilac eldorado brake calipers for the 14bff rear end. they are used because they have a parking brake.
(Posted in: my rear end)

1222101902.jpg
1361 hits | 37.07 KB | Posted: 12/22/10
1 step closer to done. 14bff w/ disk upgrade
(Posted in: my rear end)

tire.rack01.jpg
945 hits | 30.61 KB | Posted: 2/22/10
spare tire rack w/ cb antennae and light mounts
(Posted in: spare tire rack)

tire.rack03.jpg
1471 hits | 40.42 KB | Posted: 2/22/10
close up of light and c.b. antennae mounts
(Posted in: spare tire rack)

jack.rack01.jpg
936 hits | 30.33 KB | Posted: 2/22/10
hi-lift jack base holder incorporated into the tire rack, and held by wing-nut on bed rail armor
(Posted in: spare tire rack)

tire.rack08.jpg
1394 hits | 64.88 KB | Posted: 3/4/10
painted. still needs the two lugs that hold the tire tight to the top of the rack.
(Posted in: spare tire rack)

tire.rack02.jpg
1650 hits | 43.21 KB | Posted: 9/11/10
(Posted in: spare tire rack)

floorboards01.jpg
938 hits | 38.04 KB | Posted: 3/3/10
the passenger side fllorboard and support is cut out, getting prepped to be repaired
(Posted in: floorboard repair)

floorboard06.jpg
1027 hits | 37.85 KB | Posted: 3/4/10
pass. side reenforced with square tubing behind rocker
(Posted in: floorboard repair)

floorboard07.jpg
987 hits | 34.95 KB | Posted: 3/4/10
pass. side reenforced with square tubing behind rocker
(Posted in: floorboard repair)

floorboard08.jpg
1693 hits | 30.93 KB | Posted: 3/15/10
floorboard in with rocker attatched.
(Posted in: floorboard repair)

0326101438a.jpg
1833 hits | 42.03 KB | Posted: 3/28/10
door hinges removed, holes cleaned and painted
(Posted in: floorboard repair)

0327101214a.jpg
1585 hits | 33.56 KB | Posted: 3/28/10
template made from flat cardboard, a prototype cover is made from the skin o0f a donor door
(Posted in: floorboard repair)