Van Sibley
|
LIVINGSTON, LA, USA |
Registered on 2/2/2004 |
38 posts |
|
|
Posted:3/2/2004 17:35 |
|
|
Fife tire care on monterey right past mammoth. |
|
Van Sibley
|
LIVINGSTON, LA, USA |
Registered on 2/2/2004 |
38 posts |
|
|
Posted:3/3/2004 18:43 |
|
|
New tires are mounted and man they look good.I just need somewhere to try them out. On the highway they are just the kind of ride I was looking for.Alot smoother than those swampers.I need to do a little fender trimming cause turning sharp makes them rub a little.I'll need a little help with that because I don't want to put flares on it.I'm putting a set of wheel opening moldings off of a full-size on it so the cut needs to be close. |
|
Bowtie Blazer
|
Baton Rouge, LA, USA |
Registered on 5/27/2003 |
1,220 posts |
|
|
Posted:3/3/2004 21:23 |
|
|
I got an angle, grinder and am willing to give it a shot, what you doing early saturday morning like before noon? Dunno if you are a early morning person... I got my wheel wells done pretty well.
|
|
Van Sibley
|
LIVINGSTON, LA, USA |
Registered on 2/2/2004 |
38 posts |
|
|
Posted:3/3/2004 22:09 |
|
|
No plans for the morning but have some work to do later saturday.I could definatly use the help if your not busy. |
|
Bowtie Blazer
|
Baton Rouge, LA, USA |
Registered on 5/27/2003 |
1,220 posts |
|
|
Posted:3/4/2004 00:55 |
|
|
Are you in an area where we can grind at night? Just curious, I could only wish that were true here, saturday mornign is cool by me, let me know, like I said I've gotten pretty good and cutting shit and i'm always up for a fab challenge
|
|
Van Sibley
|
LIVINGSTON, LA, USA |
Registered on 2/2/2004 |
38 posts |
|
|
Posted:3/4/2004 06:00 |
|
|
Kind of hard to work at night around here,but saturday morning would be good.Your place or mine?Doesnt matter to me I can come out there or meet you out here.Just give me a time and place,as early as you would like. |
|
LOCKED UP
|
Baton Rouge, LA, USA |
Registered on 9/29/2001 |
1,256 posts |
|
|
Posted:3/4/2004 07:17 |
|
|
Yall can do whatever you need to over here .....
Covered if need be & my neighbors are all young & fearful of the scary redneck guy that welds every friday night arounf 11PM
MY WEBSITE / DELTA 4X4 CLUB
|
|
Bowtie Blazer
|
Baton Rouge, LA, USA |
Registered on 5/27/2003 |
1,220 posts |
|
|
Posted:3/4/2004 09:01 |
|
|
Will:
I don't care where, what kind of setup do you have as far as working area? My drive is a bit narrow, but I have lots o' tools, patrick has a large drive but doesnt like to get up early, and is on the other side of the world from you, although his sleep schedule may have changed with this new job. I figure if we cut fine lines it may take awhile....I have to be back at my house by noon so we should probably start at 8 at the latest regardless of meeting place just to give us some leeway with time, doubt it will take that long but smaller stuff seems to take longer.
|
|
Van Sibley
|
LIVINGSTON, LA, USA |
Registered on 2/2/2004 |
38 posts |
|
|
Posted:3/4/2004 12:20 |
|
|
We can use the warehouse where I work.It is off of mammoth drive so you wouldnt have to go too far plus I have to be in baton rouge after lunch anyway.I dont have any automotive tools at work but could bring what we need.What all do we need?
The place is Capital Stone,10389 mammoth drive. Ill be out here around 6:30 or 7:00 saturday morning,unless you prefer to work somewhere else.
cell#268-2495
home#686-9118 |
|
Bowtie Blazer
|
Baton Rouge, LA, USA |
Registered on 5/27/2003 |
1,220 posts |
|
|
Posted:3/4/2004 12:27 |
|
|
I'm all about using a warehouse, that will work out well for me, I know exactly where you are, I can bring tools too and that time is fine with me, I have a 7.0 amp angle grinder with cutting discs and all, if you have a sawzall that may come in handy but not necessary, I'm not sure what mounting your new fender's will entail but bring them and there is a hardware store right there on that corner, montery and mammoth if I remember right. The rest is just time.....I can be there around 7 or so.....my house # is 927-0284 cell 337-344-1585
probably need extension cords, i only have a 25ft and not sure about the closest hook up for electrical for where we are working
|
|