000_1495.jpg 645 hits | 66.01 KB | Posted: 6/26/05 five trucks later we were able to get him out. (Posted in: 6 26 05)
000_1496.jpg 734 hits | 36.92 KB | Posted: 6/26/05 fun time ended when bco would not start...had to get pulled to staging area by another ford...once up top for some mysterous reason started back up but found this damage once i got home. (Posted in: 6 26 05)
000_1522.JPG 911 hits | 51.88 KB | Posted: 6/29/05 GOT MY HANDS ON AN EDELBROCK PERFORMANCE 600 SERIES. CHEAP!!!!! (Posted in: Carb)
000_0007.JPG 753 hits | 44.27 KB | Posted: 6/30/05 ok after several hours of crap...realized the edelbrock wont fit and am going to have stock holley rebuilt. (Posted in: Carb)
000_0005.jpg 827 hits | 75.61 KB | Posted: 7/10/05 second try...after ordering misc. brackets and adapters from jegs i was able to get carb to fit (fuck the smog crap) (Posted in: Carb)
DSCN0858.JPG 700 hits | 97.6 KB | Posted: 2/25/06 carb, air cleaner, fuel regulator and throttle bracket. (Posted in: Carb)
000_0010.jpg 957 hits | 68.72 KB | Posted: 7/10/05 step 1: place vehicle on jack stands. (Posted in: front locker install)
000_0011.jpg 1118 hits | 65.82 KB | Posted: 7/10/05 rt front hub and rotor (Posted in: front locker install)
000_0012.jpg 1123 hits | 65.64 KB | Posted: 7/10/05 lt ft hub and rotor. (Posted in: front locker install)
000_0013.jpg 1236 hits | 55.88 KB | Posted: 7/10/05 2nd photo before disassembly of rt frt hub and rotor (Posted in: front locker install)
000_0015.jpg 1170 hits | 68.82 KB | Posted: 7/10/05 disassembly of rt side. (Posted in: front locker install)
000_0016.jpg 1201 hits | 67.68 KB | Posted: 7/10/05 rt hub...looks like i had a water leak...completely saturated in dirt and oil...not sure whether to clean or replace...if replace will have good one from left side as spare. (Posted in: front locker install)
000_0017.jpg 2061 hits | 59.21 KB | Posted: 7/10/05 left side after disassembly (Posted in: front locker install)
000_0018.jpg 1115 hits | 66.62 KB | Posted: 7/10/05 2nd shot of left side (Posted in: front locker install)
000_0019.jpg 1032 hits | 65.26 KB | Posted: 7/10/05 close up of left side. (Posted in: front locker install)
000_0002.JPG 1113 hits | 71.29 KB | Posted: 7/12/05 Third member removed from vehicle...will clean and paint since I have it out. (Posted in: front locker install)
000_0003.JPG 1108 hits | 63.87 KB | Posted: 7/12/05 no spider gears in it. (Posted in: front locker install)
000_0004.JPG 1153 hits | 59.65 KB | Posted: 7/12/05 Aussie locker components before install. (Posted in: front locker install)
000_0005.JPG 1164 hits | 62.86 KB | Posted: 7/12/05 All cleaned up and ready for install of locker. (Posted in: front locker install)
000_0006.JPG 1539 hits | 59.05 KB | Posted: 7/12/05 With aussie locker installed...just have to check tolarances...calls for between.145 - .170. (Posted in: front locker install)
locker1.jpg 1156 hits | 71.25 KB | Posted: 7/12/05 carrier back in housing. (Posted in: front locker install)
locker2.jpg 1233 hits | 77.53 KB | Posted: 7/12/05 front axles before clean up and new u joint installation. (Posted in: front locker install)
locker3.jpg 1055 hits | 69.05 KB | Posted: 7/12/05 aussie locker in carrier (Posted in: front locker install)
locker4.jpg 1080 hits | 71.39 KB | Posted: 7/12/05 another shot of locker in carrier. (Posted in: front locker install)
locker5.jpg 990 hits | 59.37 KB | Posted: 7/12/05 front view of carrier back in housing. (Posted in: front locker install)
locker6.jpg 1044 hits | 71.51 KB | Posted: 7/12/05 side shot of carrier in housing. (Posted in: front locker install)
0002.jpg 1041 hits | 47.63 KB | Posted: 7/14/05 front drive line with third member out. (Posted in: front locker install)
0003.jpg 973 hits | 53.97 KB | Posted: 7/14/05 rr shot of center diff. (Posted in: front locker install)
0004.jpg 967 hits | 64.79 KB | Posted: 7/14/05 another shot of front end. (Posted in: front locker install)
0005.jpg 1002 hits | 51.65 KB | Posted: 7/14/05 another angle. (Posted in: front locker install)
0007.jpg 1023 hits | 65.27 KB | Posted: 7/14/05 front view. (Posted in: front locker install)
0008.jpg 1024 hits | 71.28 KB | Posted: 7/14/05 drive axles all clean and repainted. (Posted in: front locker install)
0009.jpg 954 hits | 65.48 KB | Posted: 7/14/05 2nd shot of frt axles waiting for reassembly...just waiting for new u-joints, bearings and seals to come in from Randys Ring and Pinion. (Posted in: front locker install)
000_0001.jpg 704 hits | 76.21 KB | Posted: 7/17/05 another one that was left over night. (Posted in: 7 17 05)
