733760-R1-11A_10.jpg
477 hits | 99.09 KB | Posted: 6/9/05
Keith going over Jaws 1.
(Posted in: Blanca, Aug 2003)

733760-R1-13A_12.jpg
436 hits | 104.99 KB | Posted: 6/9/05
Jaws1
(Posted in: Blanca, Aug 2003)

733760-R1-12A_11.jpg
510 hits | 103.32 KB | Posted: 6/9/05
More Jaws 1
(Posted in: Blanca, Aug 2003)

733760-R1-14A_13.jpg
538 hits | 87.67 KB | Posted: 6/9/05
(Posted in: Blanca, Aug 2003)

733760-R1-15A_14.jpg
538 hits | 86.34 KB | Posted: 6/9/05
(Posted in: Blanca, Aug 2003)

733760-R1-16A_15.jpg
646 hits | 88.55 KB | Posted: 6/9/05
final shot one Jaws1
(Posted in: Blanca, Aug 2003)

New style PS Pump Front.JPG
1560 hits | 121.99 KB | Posted: 10/11/04
Saginaw pump is out of a Chevy 1 ton van and rebuilt by a pro. This pump requires a seperate resivoir.
(Posted in: New Saginaw Pump)

New Style PS Pump Rear.JPG
1353 hits | 114.78 KB | Posted: 10/11/04
Rear view of pump.
(Posted in: New Saginaw Pump)

Sag bracket out of van front.JPG
1299 hits | 119.38 KB | Posted: 10/11/04
(Posted in: New Saginaw Pump)

Sag bracket out of van rear.JPG
1197 hits | 112.8 KB | Posted: 10/11/04
(Posted in: New Saginaw Pump)

Sag bracket out of van with new pump front.JPG
1228 hits | 109.85 KB | Posted: 10/11/04
(Posted in: New Saginaw Pump)

Sag bracket out of van with new pump side.JPG
1202 hits | 109.28 KB | Posted: 10/11/04
(Posted in: New Saginaw Pump)

Top view with hoses installed.JPG
1223 hits | 118.09 KB | Posted: 10/11/04
(Posted in: New Saginaw Pump)

With PS resivoir installed.JPG
1338 hits | 113.36 KB | Posted: 10/11/04
The resivoir is out of a Chevy econo box. Lots of vehicles use a resivoir. If I had it to do over again I would get one out of a Chevy-20 van or BMW. Both have more capacity.
(Posted in: New Saginaw Pump)

New pump and bracket in truck top front.JPG
1253 hits | 107.52 KB | Posted: 10/11/04
(Posted in: New Saginaw Pump)

New pump and bracket with AC installed.JPG
1194 hits | 105.44 KB | Posted: 10/11/04
(Posted in: New Saginaw Pump)

PS cooler installed.JPG
1192 hits | 119.72 KB | Posted: 10/11/04
(Posted in: New Saginaw Pump)

two pulleys.jpg
1181 hits | 95.47 KB | Posted: 4/27/05
Picture of the two pulleys that you will usually find on a Saginaw pump. The one on the left is from a Ford e-350 van. The one on the right is one you usually find on GM vehicles.
(Posted in: New Saginaw Pump)

two pulleys big one measured.jpg
1174 hits | 82.62 KB | Posted: 4/27/05
The two pulleys again. The GM pulley measures 6.5" diameter. The center hole is .755".

(Posted in: New Saginaw Pump)

two pulleys small one measured.jpg
1037 hits | 84.72 KB | Posted: 4/27/05
The pulley on the left is off of an E-350 van Saginaw pump. It is 5.75" in diameter with the .755 diameter hole. The 5.75" is the same size you will find on the Ford C-2 PS pump. I forget the diameter of the C-2 shaft but it is about .665 or so.
(Posted in: New Saginaw Pump)

scott_broke.jpg
776 hits | 48.46 KB | Posted: 10/20/04
Another picture of Scott's busted bronco. With Keith, Scott and Shawn Clemmons.
(Posted in: Moab, Fall 04)

dustball getting a wegie on golden spike.jpg
683 hits | 76.02 KB | Posted: 10/20/04
(Posted in: Moab, Fall 04)

dustball going up launch pad.jpg
628 hits | 46.09 KB | Posted: 10/20/04
(Posted in: Moab, Fall 04)

me starting golden crack.jpg
614 hits | 42.54 KB | Posted: 10/20/04
(Posted in: Moab, Fall 04)

busted coilover.jpg
886 hits | 63.95 KB | Posted: 5/10/05
Ouch, this looks expensive!

(Posted in: Moab, Fall 04)

0240251-R1-051-24.jpg
658 hits | 74.1 KB | Posted: 6/10/05
Scott and Keith on Moab Rim.
(Posted in: Moab, Fall 04)

0240251-R1-031-14.jpg
666 hits | 78.3 KB | Posted: 6/10/05
Scott on Moab Rim. Fall 04.
(Posted in: Moab, Fall 04)

scott on moab rim.JPG
634 hits | 34.7 KB | Posted: 6/10/05
Too bad the colors did not turn out very good on this one.
(Posted in: Moab, Fall 04)

deer_1.JPG
480 hits | 110.88 KB | Posted: 11/4/04
(Posted in: Deer, Fall 04)

deer_2.JPG
513 hits | 111.94 KB | Posted: 11/4/04
(Posted in: Deer, Fall 04)

deer_3.jpg
559 hits | 47.55 KB | Posted: 12/21/04
Just another deer picture from this year.

(Posted in: Deer, Fall 04)

deer mount.JPG
509 hits | 65.99 KB | Posted: 11/26/05
Deer mounted.

(Posted in: Deer, Fall 04)

new compressor.JPG
540 hits | 104.39 KB | Posted: 6/9/05
New compressor scored for FREE! Needs a new motor though...
(Posted in: Tools)

antiwrap axle template.JPG
2642 hits | 59.69 KB | Posted: 2/7/05
I used two peices of 1/4" plate steel about 6" x 8" and made template to "fit" what I had. When I drilled the holes I had both peices tack welded together. then they were cut out with a plasma cutter. The diameter of the Sterling 10.25" axle is 3....
(Posted in: Anti Wrap Bar, winter 05)

cleaning the axle.JPG
1517 hits | 80.81 KB | Posted: 2/7/05
(Posted in: Anti Wrap Bar, winter 05)

grinding the axle.JPG
1366 hits | 80.81 KB | Posted: 2/7/05
Too bad there were no pictures taken when I set my sock and foot on fire while welding the bracket onto the axle. I still have a small scar on my leg.
(Posted in: Anti Wrap Bar, winter 05)

closeup of top anti wrap bar.JPG
1506 hits | 78.54 KB | Posted: 2/7/05
(Posted in: Anti Wrap Bar, winter 05)

view of top antiwrap with dom in square tube.JPG
1524 hits | 94.81 KB | Posted: 2/7/05
The top and bottom bars are 1.5" x .25" DOM tubing. The top bar is about 36" long, the bottom bar is about 24" long. The square tubing I used on the top bar is 2"x2" 1/4". It is about 12" long with 6" of overlap on the DOM. There are two 7/16" "8...
(Posted in: Anti Wrap Bar, winter 05)

bottom view.JPG
2627 hits | 90.85 KB | Posted: 3/18/05
Installed picture before painting.
(Posted in: Anti Wrap Bar, winter 05)

pic of shackle mount 37 inches by 2x3 inch 11 .jpg
1877 hits | 56.55 KB | Posted: 4/28/05
Picture of shackle mount while I was painting it. It is 37" long, 2"x 3" 11 gauge rectangle tube. There is a peice of 2"x2" square tube welded to it at 7" from left (driver side) to mount the actuall shackle. This peice mounts in the "drop" on the...
(Posted in: Anti Wrap Bar, winter 05)

closeup of shackle mount 2 inch square tube.jpg
1820 hits | 40.1 KB | Posted: 4/28/05
Closeup detail of where the square tubing for the actuall shackle mounts. It was 7" from the left end of the tube on my install. Yours might be a little different.

(Posted in: Anti Wrap Bar, winter 05)

back view of shackle mount installed without s.jpg
1611 hits | 49.69 KB | Posted: 4/28/05
View of shackle mount installed, looking forward.
(Posted in: Anti Wrap Bar, winter 05)

side view of shackle installed front hole for .JPG
1895 hits | 29.03 KB | Posted: 4/28/05
Side view of shackle mount. The front hole in the mount is where the shackle will bolt in. The top of the 2x2 was cut back to allow the shackle to swing forward and backward with the axle.
(Posted in: Anti Wrap Bar, winter 05)

closeup of shackle two weld in bungs with tube.jpg
1558 hits | 42.75 KB | Posted: 4/28/05
Closeup of shackle, it was made out of two 5/8" weld in bungs, one left hand thread one right hand thread and a peice of 1" ID DOM tube, about 1 1/2" long. The whole shackle is about 3". You can see the SRE's in the picture, both 5/8" one LHT the ...
(Posted in: Anti Wrap Bar, winter 05)

another view of shackle.jpg
1409 hits | 45.12 KB | Posted: 4/28/05
Just another view of the shackle assembly, note the 1/4" spacers to allow more right/left movement when installed.
(Posted in: Anti Wrap Bar, winter 05)