|
|
Hits: 2561
Size: 59.69 KB
Posted: 2/7/05
I used two peices of 1/4" plate steel about 6" x 8" and made template to "fit" what I had. When I d... | 
Hits: 1464
Size: 80.81 KB
Posted: 2/7/05
| 
Hits: 1304
Size: 80.81 KB
Posted: 2/7/05
Too bad there were no pictures taken when I set my sock and foot on fire while welding the bracket o... | 
Hits: 1452
Size: 78.54 KB
Posted: 2/7/05
| 
Hits: 1469
Size: 94.81 KB
Posted: 2/7/05
The top and bottom bars are 1.5" x .25" DOM tubing. The top bar is about 36" long, the bottom bar i... |
Hits: 2552
Size: 90.85 KB
Posted: 3/18/05
Installed picture before painting. | 
Hits: 1814
Size: 56.55 KB
Posted: 4/28/05
Picture of shackle mount while I was painting it. It is 37" long, 2"x 3" 11 gauge rectangle tube. ... | 
Hits: 1744
Size: 40.1 KB
Posted: 4/28/05
Closeup detail of where the square tubing for the actuall shackle mounts. It was 7" from the left e... | 
Hits: 1554
Size: 49.69 KB
Posted: 4/28/05
View of shackle mount installed, looking forward. | 
Hits: 1811
Size: 29.03 KB
Posted: 4/28/05
Side view of shackle mount. The front hole in the mount is where the shackle will bolt in. The top... |
Hits: 1500
Size: 42.75 KB
Posted: 4/28/05
Closeup of shackle, it was made out of two 5/8" weld in bungs, one left hand thread one right hand t... | 
Hits: 1352
Size: 45.12 KB
Posted: 4/28/05
Just another view of the shackle assembly, note the 1/4" spacers to allow more right/left movement w... | 
Hits: 1359
Size: 45.48 KB
Posted: 4/29/05
Cruddy picture of the axle plates welded onto the Sterling. Look at those welds, can you say buble... | 
Hits: 1417
Size: 47.69 KB
Posted: 4/29/05
Second picture of axle plates installed on Sterling. Not much better of a picture. | 
Hits: 1787
Size: 89.07 KB
Posted: 5/6/05
View of setup from rear of axle. |
Hits: 1789
Size: 69.26 KB
Posted: 5/6/05
Heim (SRE) and bung shackle picture 1/4. | 
Hits: 1477
Size: 73.23 KB
Posted: 5/6/05
SRE shackle 2/4. | 
Hits: 1432
Size: 68.26 KB
Posted: 5/6/05
SRE and bung picture 3/4. | 
Hits: 1428
Size: 64.47 KB
Posted: 5/6/05
SRE and bung shackle 4/4. | 
Hits: 1349
Size: 98.18 KB
Posted: 5/6/05
Detail of square tube on end of main (upper) tube. |
Hits: 1485
Size: 81.66 KB
Posted: 5/6/05
Good view of bar and shackle assembly 1/2. | 
Hits: 1799
Size: 95.57 KB
Posted: 5/6/05
Good view of square tube and shackle assembly 2/2.
| 
Hits: 2431
Size: 42.83 KB
Posted: 6/6/05
This is the template for the steel that welds onto the rear axle. The two peices are 1/4" steel tha... | | |
Anti Wrap Bar, winter 05