DSCN1436.JPG
666 hits | 76.64 KB | Posted: 11/11/03
Getting the jack stands placed.

DSCN1438.JPG
659 hits | 102.9 KB | Posted: 11/11/03
Stock open 3rd member

DSCN1439.JPG
627 hits | 74.08 KB | Posted: 11/11/03
Here's the 'C' clip that I won't be needing anymore

DSCN1440.JPG
628 hits | 115.13 KB | Posted: 11/11/03
Ring gear and carrier out

DSCN1441.JPG
626 hits | 106.25 KB | Posted: 11/11/03
Pulling the carrier bearing to make a set up bearing out of it

DSCN1446.JPG
673 hits | 46.8 KB | Posted: 11/11/03
Cookie is very excited

DSCN1447.JPG
665 hits | 107.44 KB | Posted: 11/11/03
Pinion gear, races and bearings removed

DSCN1452.JPG
708 hits | 104.3 KB | Posted: 11/11/03
New 4.56 ring gear on new ARB locker
:-)

DSCN1453.JPG
681 hits | 81.35 KB | Posted: 11/11/03
Pressing a carrier bearing on

DSCN1456.JPG
629 hits | 108.21 KB | Posted: 11/11/03
Checking backlash for first gear pattern check

DSCN1457.JPG
746 hits | 100.5 KB | Posted: 11/11/03
Had to make an adjustment

DSCN1460.JPG
622 hits | 73.09 KB | Posted: 11/11/03
Here's the final pattern on the drive side. I hope it's right.

DSCN1461.JPG
648 hits | 69.2 KB | Posted: 11/11/03
Here's the coast pattern

DSCN1464.JPG
707 hits | 104.13 KB | Posted: 11/11/03
Case all cleaned up. New bearings installed. Ready for final assembly

DSCN1465.JPG
697 hits | 69.51 KB | Posted: 11/11/03
New pinion nut and seal

DSCN1468.JPG
729 hits | 104.37 KB | Posted: 11/11/03
Filling a notch in the bearing cap for the air line to the locker

DSCN1470.JPG
606 hits | 92.94 KB | Posted: 11/11/03
Took me a minute to figure out how I was going to bend this into the case

DSCN1471.JPG
668 hits | 106.85 KB | Posted: 11/11/03
Here it is with the bulkhead fitting on the top of the case

DSCN1473.JPG
653 hits | 111.18 KB | Posted: 11/11/03
I am pretty happy with how it turned out.

DSCN1475.JPG
625 hits | 82.21 KB | Posted: 11/11/03
3rd member back in.

DSCN1476.JPG
670 hits | 91.19 KB | Posted: 11/11/03
This cap needs to be tack welded so the spring I have to add in the slip yoke won't pop it out.

DSCN1477.JPG
694 hits | 90.56 KB | Posted: 11/11/03
Break out the wire feed

DSCN1480.JPG
682 hits | 76.76 KB | Posted: 11/11/03
I'm not a master welder yet but I think it'll hold

DSCN1481.JPG
729 hits | 94.97 KB | Posted: 11/11/03
Here's how I routed the air line.

DSCN1483.JPG
634 hits | 94.98 KB | Posted: 11/11/03
While I had it out I installed this drain plug