Meixter > 1991 Ford Bronco > open folder Front Gear/Locker Install

Getting the jack stands placed.
Hits: 667
Size: 76.64 KB
Posted: 11/11/03
Getting the jack stands placed.		Stock open 3rd member
Hits: 661
Size: 102.9 KB
Posted: 11/11/03
Stock open 3rd member		Here's the 'C' clip that I won't be needing anymore
Hits: 628
Size: 74.08 KB
Posted: 11/11/03
Here's the 'C' clip that I won't be needing anymore		Ring gear and carrier out
Hits: 629
Size: 115.13 KB
Posted: 11/11/03
Ring gear and carrier out		Pulling the carrier bearing to make a set up bearing out of it
Hits: 627
Size: 106.25 KB
Posted: 11/11/03
Pulling the carrier bearing to make a set up bearing out of it
Cookie is very excited
Hits: 674
Size: 46.8 KB
Posted: 11/11/03
Cookie is very excited		Pinion gear, races and bearings removed
Hits: 666
Size: 107.44 KB
Posted: 11/11/03
Pinion gear, races and bearings removed		New 4.56 ring gear on new ARB locker :-)
Hits: 709
Size: 104.3 KB
Posted: 11/11/03
New 4.56 ring gear on new ARB locker :-)		Pressing a carrier bearing on
Hits: 682
Size: 81.35 KB
Posted: 11/11/03
Pressing a carrier bearing on		Checking backlash for first gear pattern check
Hits: 630
Size: 108.21 KB
Posted: 11/11/03
Checking backlash for first gear pattern check
Had to make an adjustment
Hits: 747
Size: 100.5 KB
Posted: 11/11/03
Had to make an adjustment 		Here's the final pattern on the drive side. I hope it's right.
Hits: 624
Size: 73.09 KB
Posted: 11/11/03
Here's the final pattern on the drive side. I hope it's right.		Here's the coast pattern
Hits: 650
Size: 69.2 KB
Posted: 11/11/03
Here's the coast pattern		Case all cleaned up. New bearings installed. Ready for final assembly
Hits: 708
Size: 104.13 KB
Posted: 11/11/03
Case all cleaned up. New bearings installed. Ready for final assembly		New pinion nut and seal
Hits: 698
Size: 69.51 KB
Posted: 11/11/03
New pinion nut and seal
Filling a notch in the bearing cap for the air line to the locker
Hits: 730
Size: 104.37 KB
Posted: 11/11/03
Filling a notch in the bearing cap for the air line to the locker		Took me a minute to figure out how I was going to bend this into the case
Hits: 607
Size: 92.94 KB
Posted: 11/11/03
Took me a minute to figure out how I was going to bend this into the case		Here it is with the bulkhead fitting on the top of the case
Hits: 669
Size: 106.85 KB
Posted: 11/11/03
Here it is with the bulkhead fitting on the top of the case		I am pretty happy with how it turned out.
Hits: 654
Size: 111.18 KB
Posted: 11/11/03
I am pretty happy with how it turned out.		3rd member back in.
Hits: 626
Size: 82.21 KB
Posted: 11/11/03
3rd member back in.
This cap needs to be tack welded so the spring I have to add in the slip yoke won't pop it out.
Hits: 671
Size: 91.19 KB
Posted: 11/11/03
This cap needs to be tack welded so the spring I have to add in the slip yoke won't pop it out.		Break out the wire feed
Hits: 695
Size: 90.56 KB
Posted: 11/11/03
Break out the wire feed		I'm not a master welder yet but I think it'll hold
Hits: 683
Size: 76.76 KB
Posted: 11/11/03
I'm not a master welder yet but I think it'll hold		Here's how I routed the air line.
Hits: 730
Size: 94.97 KB
Posted: 11/11/03
Here's how I routed the air line.		While I had it out I installed this drain plug
Hits: 636
Size: 94.98 KB
Posted: 11/11/03
While I had it out I installed this drain plug
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2022 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog