bronco-4-2006_017.jpg
11200 hits | 62.98 KB | Posted: 4/25/06
homemade tool to remove axle pivot bushings
(Posted in: axle pivot bushing tool)

bronco-4-2006_021.jpg
9221 hits | 61.4 KB | Posted: 4/25/06
Insert all-thread into bushing, place socket on side of bushing without metal lip (shown reversed in pic)
(Posted in: axle pivot bushing tool)

bronco-4-2006_032.jpg
9131 hits | 68.54 KB | Posted: 4/25/06
reverse tool to install new bushing using washer under socket, hammer used only to keep bushing straight
(Posted in: axle pivot bushing tool)

bronco-4-2006_038.jpg
8461 hits | 67.05 KB | Posted: 4/25/06
bushing will "pop" loose
(Posted in: axle pivot bushing tool)

bronco-4-2006_033.jpg
8426 hits | 64.73 KB | Posted: 4/25/06
place collar on other side, then plate and attach nuts&washers
(Posted in: axle pivot bushing tool)

bronco-4-2006_018.jpg
8249 hits | 63.51 KB | Posted: 4/25/06
12" length of 1/2" all-thread, 2.5" I.D. x0.25" thick pipe collar, 1/2" thick metal plate, 13/16" impact socket, nuts and large washers
(Posted in: axle pivot bushing tool)

bronco-4-2006_037.jpg
8153 hits | 66.85 KB | Posted: 4/25/06
give a sharp blow with hammer, re-tighten nuts if needed
(Posted in: axle pivot bushing tool)

bronco-4-2006_029.jpg
7723 hits | 61.57 KB | Posted: 4/25/06
tighten nuts on both sides until they stop (100-120 ft.lbs.)
(Posted in: axle pivot bushing tool)

digibronco12.jpg
6010 hits | 27.96 KB | Posted: 6/29/03
Skyler "fastback" softtop
(Posted in: Skyler softtop)

DSC01982.JPG
5806 hits | 66.36 KB | Posted: 8/23/08
37s and PSC Rocker Knockers
(Posted in: 2002 TJ)

Bronco_Image1cc.JPG
4811 hits | 56.29 KB | Posted: 10/20/03
Locked and Loaded......35X12.5X15 BFG MT's.....LS & 4.56's Front.....Detroit Locker & 4.56's Rear
(Posted in: TrUcK)

drivers side.jpg
4762 hits | 52.69 KB | Posted: 12/10/03
drivers side mounted with 5/8" u-bolts.
(Posted in: Front Dana 60 Swap 8/03)

shackle angle.jpg
4609 hits | 83.73 KB | Posted: 11/19/03
This is just mocked up, unweighted. Not good shackle angle.
(Posted in: Front Dana 60 Swap 8/03)

35s1.jpg
4493 hits | 55.48 KB | Posted: 12/15/03
35" on a 16.5 centered about 1.5" further than stock. I am jsut using these tires to get everything in place.
(Posted in: Front Dana 60 Swap 8/03)

modified body mount.jpg
4471 hits | 62.27 KB | Posted: 12/3/03
Modified body mount.
(Posted in: Front Dana 60 Swap 8/03)

drivershanger.jpg
4443 hits | 75.6 KB | Posted: 11/15/03
from the back side, the drivers hanger
(Posted in: Front Dana 60 Swap 8/03)

shackle angle 2.jpg
4301 hits | 54.79 KB | Posted: 12/3/03
Current shackle angle, before cutting
(Posted in: Front Dana 60 Swap 8/03)

pass. hangar complete.jpg
4287 hits | 59.04 KB | Posted: 12/10/03
pass. side hangar complete.
(Posted in: Front Dana 60 Swap 8/03)

passhangar.jpg
4283 hits | 72.34 KB | Posted: 11/15/03
pass. side hanger
(Posted in: Front Dana 60 Swap 8/03)

P1010976.JPG
4057 hits | 105.48 KB | Posted: 3/11/07
An American Classic
1996 Ford Bronco Eddie Bauer
351 CU engine
(Posted in: My pictures)

bronco 2.jpg
4046 hits | 68.79 KB | Posted: 2/21/06
(Posted in: Bronco pics)

new shackle angle 2.jpg
4008 hits | 79.17 KB | Posted: 3/29/04
Better. Still about 5.5" higher where spring bolts in the front, but I am happy with this. We shall see how it flexes
(Posted in: Front Dana 60 Swap 8/03)

RB_Rear.jpg
3961 hits | 63.43 KB | Posted: 10/21/03
(Posted in: RoLL caGe)

4.jpg
3905 hits | 45.42 KB | Posted: 8/23/03
On the junkyard truck
(Posted in: Front Dana 60 Swap 8/03)

hangar compare.jpg
3464 hits | 56.51 KB | Posted: 12/3/03
Hangar comparison
(Posted in: Front Dana 60 Swap 8/03)

bronco22.jpg
3458 hits | 27.81 KB | Posted: 6/29/03
1984 FORD Bronco XLT 4X4 - original condition
(Posted in: side view)

leafs.jpg
3421 hits | 91.9 KB | Posted: 11/18/03
(Posted in: Front Dana 60 Swap 8/03)

Untitled.jpg
3391 hits | 42.38 KB | Posted: 12/19/04
My 1988 Ford Bronco XLT!
(Posted in: My Bronco)

35s2.jpg
3378 hits | 56.04 KB | Posted: 12/15/03
(Posted in: Front Dana 60 Swap 8/03)

drivers hangar mod.jpg
3359 hits | 56.17 KB | Posted: 12/3/03
This is how I modified the rearward hangar.
(Posted in: Front Dana 60 Swap 8/03)

painted.jpg
3357 hits | 93.22 KB | Posted: 11/15/03
Painted
(Posted in: Front Dana 60 Swap 8/03)

mocked up hangar.jpg
3326 hits | 79.78 KB | Posted: 10/29/03
(Posted in: Front Dana 60 Swap 8/03)

bronco 4.jpg
3301 hits | 59.55 KB | Posted: 2/21/06
(Posted in: Bronco pics)

sideprofile.jpg
3298 hits | 12.62 KB | Posted: 4/3/04
(Posted in: superbronco pics)

crap tires.jpg
3275 hits | 57.73 KB | Posted: 12/18/03
on some crappy tires
(Posted in: Front Dana 60 Swap 8/03)

38s2.jpg
3261 hits | 54.66 KB | Posted: 12/18/03
looks good with 38s

(Posted in: Front Dana 60 Swap 8/03)

complete4.jpg
3260 hits | 91.47 KB | Posted: 4/3/04
Final setup
(Posted in: Front Dana 60 Swap 8/03)

xmember3.jpg
3248 hits | 98.27 KB | Posted: 11/13/03
(Posted in: Front Dana 60 Swap 8/03)

engine xmember aftercut.jpg
3241 hits | 86.65 KB | Posted: 11/13/03
still needs to be cleaned up with the grinder.
(Posted in: Front Dana 60 Swap 8/03)

Wreck 001.jpg
3228 hits | 75.21 KB | Posted: 10/16/03
(Posted in: Wreck)

new shackle angle.jpg
3212 hits | 85.98 KB | Posted: 3/29/04
raised up shackle into hangar about 1.5"
(Posted in: Front Dana 60 Swap 8/03)

driversboxed.jpg
3211 hits | 87.04 KB | Posted: 11/11/03
driver's side boxed in.
(Posted in: Front Dana 60 Swap 8/03)

bronco1.jpg
3206 hits | 57.59 KB | Posted: 2/21/06
Crushing Car

(Posted in: Bronco pics)

35s3.jpg
3200 hits | 56.92 KB | Posted: 12/15/03
It sits up pretty tall. I am planning on 37"s
(Posted in: Front Dana 60 Swap 8/03)

warn hubs.jpg
3200 hits | 71.68 KB | Posted: 4/27/04
(Posted in: Front Dana 60 Swap 8/03)