|
|
Hits: 1109
Size: 73.56 KB
Posted: 8/19/03
The cross I made for the adapter. I believe the dimension was 2 3/4 each way. | 
Hits: 867
Size: 61.36 KB
Posted: 8/19/03
I used hollow 1" square stock and then filled it with 5000psi epoxy (I think it was 5000psi, it was... | 
Hits: 823
Size: 54.2 KB
Posted: 8/19/03
Here it is on the arm without the coil seat. | 
Hits: 873
Size: 61.45 KB
Posted: 7/31/03
Had to grind a little clearance for the bolt heads | 
Hits: 855
Size: 50.71 KB
Posted: 7/31/03
The adapter to mount the 1980 coils to the 1979 radius arms |
Hits: 829
Size: 52.75 KB
Posted: 8/19/03
Another angle, hopefully between the two it is apparent what I did. | 
Hits: 804
Size: 55.57 KB
Posted: 8/19/03
Here is the bottom with the spaced holes to match the 79 arm and the big bolt for the 80 coil with t... | 
Hits: 772
Size: 71.47 KB
Posted: 7/31/03
Another shot | 
Hits: 838
Size: 66.04 KB
Posted: 7/31/03
In place on the radius arm. Provides a 1-1.5 inch lift, but I need to test it still to see if it it... | 
Hits: 775
Size: 61.81 KB
Posted: 7/31/03
The truss I built, mostly for fun and looks, but it will function |
Hits: 828
Size: 58.78 KB
Posted: 7/31/03
Even though the housing is cast, the welds look great. Maybe it isn't totally cast? I don't know. | 
Hits: 846
Size: 42.02 KB
Posted: 7/31/03
This will be my trackbar, eventually | 
Hits: 839
Size: 40.62 KB
Posted: 7/31/03
The steering Rob Ellis whipped up for me | 
Hits: 785
Size: 56.33 KB
Posted: 7/31/03
Helm-jointed ends | 
Hits: 850
Size: 58.38 KB
Posted: 7/31/03
Helms here too |
Hits: 780
Size: 56.77 KB
Posted: 7/31/03
Check out the displacement angle | 
Hits: 810
Size: 69.79 KB
Posted: 7/31/03
Trial hanging | 
Hits: 794
Size: 65.05 KB
Posted: 7/31/03
More work to be done | 
Hits: 801
Size: 65.29 KB
Posted: 7/31/03
There needs to be some trimming done | 
Hits: 852
Size: 61.01 KB
Posted: 7/31/03
You can see what needs to change |
Hits: 774
Size: 55.16 KB
Posted: 7/31/03
The front cut | 
Hits: 856
Size: 46.51 KB
Posted: 7/31/03
The rear cut | 
Hits: 843
Size: 36.93 KB
Posted: 7/31/03
Two brackets to strengthen and give a clean look | 
Hits: 793
Size: 48.43 KB
Posted: 7/31/03
The clean look | 
Hits: 823
Size: 49.86 KB
Posted: 7/31/03
There are even 1/2" draining holes |
Hits: 883
Size: 69.19 KB
Posted: 7/31/03
Everybody should have an axle hoist! | 
Hits: 861
Size: 44.89 KB
Posted: 7/31/03
Nearly ready to swing under the truck | 
Hits: 865
Size: 49.59 KB
Posted: 7/31/03
I just have to fix the busted ARB locker fitting. You can't really see it, but the copper tube crac... | 
Hits: 1034
Size: 44.05 KB
Posted: 8/11/03
I rolled the rebuilt axle out of the garage for the first time. You can see the epoxy in the coil a... | 
Hits: 1537
Size: 55.21 KB
Posted: 8/11/03
Should look pretty cool when installed...duh! |
Hits: 1025
Size: 57.67 KB
Posted: 8/22/03
Axle set in place under the truck | 
Hits: 884
Size: 21.35 KB
Posted: 8/22/03
Closer view, but not very clear. I will have better pictures on the next roll. | 
Hits: 896
Size: 51.58 KB
Posted: 9/30/03
My version of the trackbar mount | 
Hits: 862
Size: 44.19 KB
Posted: 9/30/03
From the side | 
Hits: 838
Size: 42.1 KB
Posted: 9/30/03
The reinforcing rod on the back |
Hits: 962
Size: 40.21 KB
Posted: 9/30/03
The major work is done | 
Hits: 844
Size: 35.77 KB
Posted: 9/30/03
Everything clears, and looks like it will clear beyond this point. | 
Hits: 849
Size: 51.57 KB
Posted: 12/18/03
Crossmember from front | 
Hits: 882
Size: 49.46 KB
Posted: 12/18/03
Crossmember from back | 
Hits: 852
Size: 30.4 KB
Posted: 1/23/04
My "swamper bumper": half of a 1.5" pipe welded across the radius arm so the swamper lugs glide smoo... |
SAS