DrHader.jpg 699 hits | 99.84 KB | Posted: 9/19/06 Driver's side header....plenty of room for the steering shaft with these! (Posted in: 460 CV Project)
DCP_7375.jpg 684 hits | 85.01 KB | Posted: 7/20/05 Newest member of the family. GS model w/108k on the clock (Posted in: 1997 Grand Marquis GS)
DCP_7376.jpg 635 hits | 105.76 KB | Posted: 7/20/05 I still prefer the '92-'94 body style. Something about the grill I don't like (Posted in: 1997 Grand Marquis GS)
DCP_7378.jpg 674 hits | 71.71 KB | Posted: 7/20/05 I do prefer the rearend design of the '95-'97 better than the '92-'94 (Posted in: 1997 Grand Marquis GS)
DCP_7379.jpg 649 hits | 88.27 KB | Posted: 7/20/05 Yep, I like it. (Posted in: 1997 Grand Marquis GS)
DCP_7380.jpg 703 hits | 90.05 KB | Posted: 7/20/05 Right rear 3/4 shot (Posted in: 1997 Grand Marquis GS)
DCP_7381.jpg 711 hits | 81.39 KB | Posted: 7/20/05 The window and lock buttons light up. That's cool! (Posted in: 1997 Grand Marquis GS)
DCP_7382.jpg 779 hits | 88.62 KB | Posted: 7/20/05 Two-tone dash is different. (Posted in: 1997 Grand Marquis GS)
DCP_7383.jpg 756 hits | 79.02 KB | Posted: 7/20/05 I don't care for the '96 steering wheel. Maybe if it were leather I would like it more. (Posted in: 1997 Grand Marquis GS)
DCP_7384.jpg 850 hits | 83.31 KB | Posted: 7/20/05 Missing the engine cover and a little dusty. (Posted in: 1997 Grand Marquis GS)
VoltageRegScrews.jpg 658 hits | 75.23 KB | Posted: 3/8/06 Remove the 4 screws that the blue arrows point too. (T20 torx bit) (Posted in: Voltage Regulator Swap)
SideView.jpg 639 hits | 69.06 KB | Posted: 3/8/06 Side shot of the voltage regulator (Posted in: Voltage Regulator Swap)
ScrewRemoved.jpg 682 hits | 79.45 KB | Posted: 3/8/06 When the screws are removed the voltage regulator will be pushed up by the brushes. (Posted in: Voltage Regulator Swap)
ScrewRemovedSide.jpg 683 hits | 60.07 KB | Posted: 3/8/06 Another shot with the screws removed. The regulator simply lifts out. (Posted in: Voltage Regulator Swap)
VoltReg3.pg.jpg 654 hits | 52.36 KB | Posted: 3/8/06 Voltage regulator. (The 2 screws in the picture hold the brush assembly to the regulator. T20 Torx bit) (Posted in: Voltage Regulator Swap)
VoltReg1.jpg 661 hits | 46.47 KB | Posted: 3/8/06 Side view....showing brush assembly (Posted in: Voltage Regulator Swap)
Brushes.jpg 671 hits | 65.01 KB | Posted: 3/8/06 This is the brush assembly bolted in place on the back of the voltage regulator (Posted in: Voltage Regulator Swap)
BrushesRemoved.jpg 657 hits | 54.12 KB | Posted: 3/8/06 When you remove the 2 screws....the brush assembly simply comes off of the regulator (Posted in: Voltage Regulator Swap)
BrushesRemovedTop.jpg 681 hits | 45.93 KB | Posted: 3/8/06 Another shot of the brushes removed (Posted in: Voltage Regulator Swap)
BrushRetainer.jpg 667 hits | 55.8 KB | Posted: 3/8/06 When you go to reinstall the regulator the brushes have to be held back into the housing. Use a paper clip to hold them in place. (Posted in: Voltage Regulator Swap)
Brushes1.jpg 646 hits | 54.66 KB | Posted: 3/8/06 With the retaining screws tight, press the brushes into the housing. (Posted in: Voltage Regulator Swap)
BrushesLocked.jpg 654 hits | 60.38 KB | Posted: 3/8/06 Here you can see that the brushes are held in place with the paper clip (Posted in: Voltage Regulator Swap)
BrushesLocked1.jpg 740 hits | 58.68 KB | Posted: 3/8/06 Another view of the brushes held in place (Posted in: Voltage Regulator Swap)
InstallingReg.jpg 669 hits | 76.66 KB | Posted: 3/8/06 To install, simply lay the regulator into place. (Posted in: Voltage Regulator Swap)
