|
|
Hits: 695
Size: 38.76 KB
Posted: 4/20/04
Shop towel holder constructed of D44 long side shaft, TTB radius arm brackets, D44 side gear | 
Hits: 667
Size: 48.74 KB
Posted: 4/20/04
The side gear is retained by a c-clip groove I cut | 
Hits: 609
Size: 54.79 KB
Posted: 5/11/04
Grinder pedestal. 8.8 with D44 spindle & hub on top | 
Hits: 566
Size: 76.96 KB
Posted: 5/11/04
worked the stock shock mount into the base | 
Hits: 561
Size: 73.93 KB
Posted: 5/11/04
this is my water pot, hope it holds water |
Hits: 626
Size: 72.12 KB
Posted: 5/11/04
unlock the lockout, spin it around to the grinder of choice, re-engage lockout | 
Hits: 590
Size: 72.74 KB
Posted: 5/11/04
rear view, note the TTB sacrifice which watches over me at all times | 
Hits: 628
Size: 66.05 KB
Posted: 6/12/04
Floor jack lifted saddle, super handy | 
Hits: 547
Size: 76.84 KB
Posted: 6/12/04
The saddle is retained with a bit of a D44 pinion that drops into the jack, then hand-tighten the pi... | 
Hits: 558
Size: 87.42 KB
Posted: 7/17/04
Workbench receivers are very handy |
Hits: 566
Size: 73.32 KB
Posted: 9/23/04
Another jack extension, this one 12" high | 
Hits: 542
Size: 57.75 KB
Posted: 10/21/04
axle holder; don't ask why the tubes are cut, I didn't do it | 
Hits: 557
Size: 56.67 KB
Posted: 10/21/04
hold-downs are modified 10.25 bearing caps | 
Hits: 565
Size: 70.38 KB
Posted: 10/28/04
| 
Hits: 525
Size: 58.06 KB
Posted: 10/28/04
|
Hits: 596
Size: 87.77 KB
Posted: 11/18/04
| 
Hits: 615
Size: 85.69 KB
Posted: 11/18/04
| 
Hits: 581
Size: 61.8 KB
Posted: 11/18/04
| 
Hits: 609
Size: 55.54 KB
Posted: 11/18/04
| 
Hits: 605
Size: 82.03 KB
Posted: 11/18/04
|
Hits: 601
Size: 95.59 KB
Posted: 11/29/04
| 
Hits: 534
Size: 97.37 KB
Posted: 11/29/04
| 
Hits: 573
Size: 79.02 KB
Posted: 11/29/04
| 
Hits: 478
Size: 79.98 KB
Posted: 11/22/04
| 
Hits: 658
Size: 69.18 KB
Posted: 11/22/04
|
Hits: 724
Size: 57.88 KB
Posted: 1/23/05
Shorter beam is 8 lug D44 HD TTB. Long beam is 5 lug TTB | 
Hits: 773
Size: 55.73 KB
Posted: 1/23/05
The knuckles won't swap because ball joint spacing is different by approx 1/2". Note 8 lug knuckle ... | 
Hits: 600
Size: 67.28 KB
Posted: 2/27/05
Cheap welding magnets just have a circular magnet surrounded by plastic | 
Hits: 641
Size: 58.26 KB
Posted: 2/27/05
The plastic melts if exposed to high enough temps | 
Hits: 590
Size: 85.52 KB
Posted: 4/12/06
|
Hits: 582
Size: 79.53 KB
Posted: 4/12/06
| 
Hits: 563
Size: 32.46 KB
Posted: 11/11/06
| 
Hits: 490
Size: 27.87 KB
Posted: 11/11/06
| 
Hits: 562
Size: 29.24 KB
Posted: 11/20/06
| 
Hits: 578
Size: 39.64 KB
Posted: 11/20/06
|
Hits: 581
Size: 59.13 KB
Posted: 1/4/07
| 
Hits: 651
Size: 54.75 KB
Posted: 1/4/07
| 
Hits: 507
Size: 74.49 KB
Posted: 11/4/07
| 
Hits: 454
Size: 72.55 KB
Posted: 11/4/07
| 
Hits: 490
Size: 60.05 KB
Posted: 11/4/07
|
Hits: 524
Size: 50.58 KB
Posted: 11/11/07
| 
Hits: 543
Size: 60.31 KB
Posted: 11/23/07
| 
Hits: 459
Size: 78.92 KB
Posted: 12/29/07
| 
Hits: 494
Size: 81.3 KB
Posted: 12/29/07
| 
Hits: 494
Size: 59.45 KB
Posted: 12/29/07
|
Hits: 507
Size: 64.15 KB
Posted: 12/29/07
| 
Hits: 441
Size: 34.77 KB
Posted: 12/29/07
| 
Hits: 531
Size: 68.33 KB
Posted: 1/2/08
| 
Hits: 549
Size: 48.32 KB
Posted: 1/2/08
| 
Hits: 613
Size: 72.5 KB
Posted: 1/2/08
|
Hits: 841
Size: 32.1 KB
Posted: 1/2/08
| 
Hits: 899
Size: 42.42 KB
Posted: 1/2/08
| 
Hits: 956
Size: 53.38 KB
Posted: 1/2/08
| | |
Misc stuff