Flutter video.wmv 4263 hits | 6.18 MB | Posted: 5/15/07 Flutter video (Posted in: My 05)
DSCF0021.mov 2960 hits | 7.78 MB | Posted: 7/24/03 Here's video of the Excursion being remote started -- the whistling of the turbo is evident through the Hypermax exhaust even while idling. (Posted in: Hypermax 3.5" downpipe & 5" exhaust)
Hypermax_Exhaust.mov 3356 hits | 1.13 MB | Posted: 2/24/04 Video of the Excursion starting up and idling with the Hypermax exhaust (Posted in: Exhaust Sounds & Videos)
Hypermax_high_idle.mov 2666 hits | 3.97 MB | Posted: 2/26/04 High-idling with the Hypermax exhaust (very loud on those cold mornings) (Posted in: Exhaust Sounds & Videos)
Hypermax_rev.mov 2750 hits | 1.14 MB | Posted: 2/26/04 Revving the PSD through the Hypermax exhaust Noticed the pronounced whistle of the turbo. (Posted in: Exhaust Sounds & Videos)
Hypermax_burnout.mov 2636 hits | 3.15 MB | Posted: 2/26/04 Testing the burnout capabilities of the X with the Hypermax exhaust and chip. It manages to chirp the tires shifting into 2nd gear. (Posted in: Exhaust Sounds & Videos)
ks95-stoplight_320x240s3.mov 2924 hits | 1.24 MB | Posted: 3/6/04 My Excursion was used in a commercial for a local radio station! Note that it's not me driving it, they hired some high school kids to sit in for the part. (Posted in: My X in a TV commercial)
Part 1 of the video shows pulling/pushing on the steering knuckle and illustrates how a worn/loose ball joint moves in place. When a ball joint is worn out, steering is affect... (Posted in: Ball Joint Replacement)
How to remove Dana 50 hub.mp4 7475 hits | 652.63 KB | Posted: 12/16/05 This video clip shows how to remove the hub from a Dana 50 frontend off of an Excursion. This also applies to an F250 or F350 frontend as well. (Posted in: Ball Joint Replacement)
3b-Remove Ball Joints-Remove Hub.mp4 7077 hits | 990.82 KB | Posted: 9/11/06 Removing the hub from the dana 50 front axle. (Posted in: Ball Joint Replacement)
4a-Remove axle c-clip.mp4 6347 hits | 1.54 MB | Posted: 9/11/06 Remove axle c-clip from dana 50 front axle. (Posted in: Ball Joint Replacement)
4b-Remove washers.mp4 6134 hits | 655.33 KB | Posted: 9/11/06 Remove the 3 washers from the dana 50 front axle. (Posted in: Ball Joint Replacement)
4c-Remove drag link.mp4 5779 hits | 5.3 MB | Posted: 9/11/06 Removing the drag link from the front end. (Posted in: Ball Joint Replacement)
4d-Loosen bolts on lug nut backplate.mp4 6543 hits | 1.52 MB | Posted: 9/11/06 Loosen the bolts behind the lug lugs the dana 50 (this is the hub assembly, which includes your bearings, that you'll be removing). (Posted in: Ball Joint Replacement)
5a-Remove knuckle:axle washer.mp4 5489 hits | 850.29 KB | Posted: 9/11/06 Remove the knuckle/axle washer. Note the grooves face in towards the differential. (Posted in: Ball Joint Replacement)
6a-Remove c-clip.mp4 5059 hits | 2.68 MB | Posted: 9/11/06 Remove the c-clip from the steering knuckle. (Posted in: Ball Joint Replacement)
6b-Remove lower ball joint.mp4 6005 hits | 1.22 MB | Posted: 9/11/06 Remove the lower ball joint with a BFH. (Posted in: Ball Joint Replacement)
6c-Remove upper ball joint.mp4 6653 hits | 3.49 MB | Posted: 9/11/06 Remove the upper ball joint with the proper ball joint removal tool and air tools! (Posted in: Ball Joint Replacement)
7a-install upper ball joint.mp4 6190 hits | 2.29 MB | Posted: 9/11/06 Using the ball joint press and air tools, install the new ball joints. This process is fairly straight forward -- video of the top ball joint is shown but the process is repeated for both. (Posted in: Ball Joint Replacement)
8b-Inner seal.mp4 6064 hits | 2.52 MB | Posted: 9/11/06 Remove and install the new inner axle seal. (Outer axle seal should be pressed in by a shop or dealer with a press) (Posted in: Ball Joint Replacement)
Noticed the pronounced whistle of the turbo.