DCP_4929.jpg 1078 hits | 103.68 KB | Posted: 8/17/03 That's it...the motor is missing!!!! (Posted in: New Engine Project)
DCP_4930.jpg 1045 hits | 109.17 KB | Posted: 8/17/03 At least I didn't have to dicharge the A/C (Posted in: New Engine Project)
DCP_4931.jpg 1043 hits | 112.98 KB | Posted: 8/17/03 OOPS...shouldn't have moved turned the wheels with the PS disconnected. (Posted in: New Engine Project)
DCP_4933.jpg 1059 hits | 79.15 KB | Posted: 8/17/03 The new tenant arrives! (Posted in: New Engine Project)
DCP_4934.jpg 919 hits | 97.68 KB | Posted: 8/17/03 Looks like it will fit. (Posted in: New Engine Project)
DCP_4936.jpg 1009 hits | 105.7 KB | Posted: 8/17/03 Thank GOD for the engine leveler! (Posted in: New Engine Project)
DCP_4937.jpg 986 hits | 108.4 KB | Posted: 8/17/03 Just misses the radiator support (Posted in: New Engine Project)
DCP_4938.jpg 1079 hits | 109.15 KB | Posted: 8/17/03 Yep....it'll fit. (Posted in: New Engine Project)
DCP_4939.JPG 1001 hits | 97.2 KB | Posted: 8/20/03 Engine is in! (Posted in: New Engine Project)
DCP_4940.JPG 897 hits | 98.4 KB | Posted: 8/20/03 Looks nice in there (Posted in: New Engine Project)
DCP_4941.JPG 983 hits | 94.7 KB | Posted: 8/20/03 Hmm...leave the hood off? (Posted in: New Engine Project)
DCP_4942.JPG 860 hits | 84.42 KB | Posted: 8/20/03 Hood's back on (Posted in: New Engine Project)
DCP_4943.JPG 996 hits | 96.95 KB | Posted: 8/20/03 Need to clean up under there (Posted in: New Engine Project)
DCP_4944.JPG 978 hits | 98.38 KB | Posted: 8/20/03 Have to clean the K&N too (Posted in: New Engine Project)
DCP_5822.jpg 713 hits | 66.14 KB | Posted: 4/10/04 Throttle cable mount. Using the original alternator bracket and a cut piece of angle steel (Posted in: New Engine Project)
DCP_5823.jpg 807 hits | 68.9 KB | Posted: 4/10/04 Close up of cable mounts. Cruise cable is cut from the throttle cable and drilled to mount to new intake (Posted in: New Engine Project)
DCP_5824.jpg 834 hits | 72.28 KB | Posted: 4/10/04 Another view of the throttle cable (Posted in: New Engine Project)
DCP_5825.jpg 827 hits | 72.32 KB | Posted: 4/10/04 Throttle cable top view (Posted in: New Engine Project)
DCP_5826.jpg 843 hits | 60.84 KB | Posted: 4/10/04 Orignal '00 cruise mount ground down to accept '93 throttle cable connector (Posted in: New Engine Project)
DCP_5828.jpg 767 hits | 57.19 KB | Posted: 4/10/04 Another view of ground down mount (Posted in: New Engine Project)
93DPFE.jpg 1102 hits | 35.3 KB | Posted: 4/21/04 This is a lousy pic of my DPFE sensor mounted on the rear of my '00 intake (Posted in: New Engine Project)
PassengerSide.jpg 849 hits | 87.01 KB | Posted: 4/21/04 Passenger side picture of the engine (Posted in: New Engine Project)
EGRSolenoid.jpg 1142 hits | 74.43 KB | Posted: 4/21/04 '93 EGR solenoid mounted in the stock '00 location (Posted in: New Engine Project)
EGRSupplyTube.jpg 873 hits | 60.23 KB | Posted: 4/21/04 The red lines are the EGR supply tube on an '01 Grand Marquis engine (Posted in: New Engine Project)
EGRSupplyTube2.jpg 1086 hits | 81.26 KB | Posted: 4/21/04 The red lines are the EGR supply tube. The black part with the grey plug is the '01 DPFE sensor (Posted in: New Engine Project)
EGRSupplyTube5.jpg 981 hits | 121.67 KB | Posted: 4/21/04 Better shot of the EGR supply from passenger side exhaust manifold up. (Posted in: New Engine Project)
EGRSupplyTube6.jpg 1027 hits | 107.73 KB | Posted: 4/21/04 Another angle on the supply tube. (Posted in: New Engine Project)
DCP_4930.jpg 840 hits | 88.24 KB | Posted: 9/5/04 Passenger side engine mount pad
The red arrows point where the bolt heads are located. (Posted in: New Engine Project)
DCP_4931.jpg 931 hits | 91.02 KB | Posted: 9/5/04 Drivers side engine mount pad
The arrows point to where the bolt heads are located. (Posted in: New Engine Project)
PrintedCircuitBoard.jpg 901 hits | 89.71 KB | Posted: 1/9/05 Finally opened up the '00 transmission to install the older TCC Solenoid. This is the printed circuit board Ford started using in '98-up 4R70W's (Posted in: New Engine Project)
StockParts.jpg 858 hits | 58.79 KB | Posted: 1/9/05 Here are the two solenoids side by side. (Posted in: New Engine Project)
DCP_6424.jpg 901 hits | 79.28 KB | Posted: 1/9/05 The parts are identical in size and shape except for the electrical connector. (Posted in: New Engine Project)
DCP_6425.jpg 829 hits | 37.55 KB | Posted: 1/9/05 Blurry...but just for reference (Posted in: New Engine Project)
DCP_6428.jpg 916 hits | 40.51 KB | Posted: 1/9/05 Cutting down the shroud around the connectors showed that the contacts are the same size as well. (Posted in: New Engine Project)
DCP_6427.jpg 905 hits | 38.55 KB | Posted: 1/9/05 The arrow points to a "bump" on the side of the '93 solenoid. I found out, after installing it back in the transmission, that this won't let the CB plug in completely. (Posted in: New Engine Project)
DCP_6426.jpg 723 hits | 40.53 KB | Posted: 1/9/05 Better picture of the "bump". I didn't feel like trying to make the bump look like the lock tab, so I just ground it off. (Posted in: New Engine Project)
