Raymond Jones > 1993 Mercury Grand Marquis > open folder Voltage Regulator Swap

Remove the 4 screws that the blue arrows point too. (T20 torx bit)
Hits: 596
Size: 75.23 KB
Posted: 3/8/06
Remove the 4 screws that the blue arrows point too. (T20 torx bit)		Side shot of the voltage regulator
Hits: 579
Size: 69.06 KB
Posted: 3/8/06
Side shot of the voltage regulator		When the screws are removed the voltage regulator will be pushed up by the brushes.
Hits: 611
Size: 79.45 KB
Posted: 3/8/06
When the screws are removed the voltage regulator will be pushed up by the brushes.		Another shot with the screws removed. The regulator simply lifts out.
Hits: 608
Size: 60.07 KB
Posted: 3/8/06
Another shot with the screws removed. The regulator simply lifts out.		Voltage regulator. (The 2 screws in the picture hold the brush assembly to the regulator. T20 Torx b...
Hits: 589
Size: 52.36 KB
Posted: 3/8/06
Voltage regulator. (The 2 screws in the picture hold the brush assembly to the regulator. T20 Torx b...
Side view....showing brush assembly
Hits: 596
Size: 46.47 KB
Posted: 3/8/06
Side view....showing brush assembly		This is the brush assembly bolted in place on the back of the voltage regulator
Hits: 597
Size: 65.01 KB
Posted: 3/8/06
This is the brush assembly bolted in place on the back of the voltage regulator		Brush assembly screws loosened
Hits: 641
Size: 65.5 KB
Posted: 3/8/06
Brush assembly screws loosened		When you remove the 2 screws....the brush assembly simply comes off of the regulator
Hits: 585
Size: 54.12 KB
Posted: 3/8/06
When you remove the 2 screws....the brush assembly simply comes off of the regulator		Another shot of the brushes removed
Hits: 618
Size: 45.93 KB
Posted: 3/8/06
Another shot of the brushes removed
When you go to reinstall the regulator the brushes have to be held back into the housing. Use a pape...
Hits: 605
Size: 55.8 KB
Posted: 3/8/06
When you go to reinstall the regulator the brushes have to be held back into the housing. Use a pape...		With the retaining screws tight, press the brushes into the housing.
Hits: 578
Size: 54.66 KB
Posted: 3/8/06
With the retaining screws tight, press the brushes into the housing.		Here you can see that the brushes are held in place with the paper clip
Hits: 593
Size: 60.38 KB
Posted: 3/8/06
Here you can see that the brushes are held in place with the paper clip		Another view of the brushes held in place
Hits: 673
Size: 58.68 KB
Posted: 3/8/06
Another view of the brushes held in place		To install, simply lay the regulator into place.
Hits: 604
Size: 76.66 KB
Posted: 3/8/06
To install, simply lay the regulator into place.
Ready to bolt in
Hits: 540
Size: 82.94 KB
Posted: 3/8/06
Ready to bolt in		Tighten the mounting bolts
Hits: 580
Size: 77.12 KB
Posted: 3/8/06
Tighten the mounting bolts		When the regulator is in place and screws tightened, pull the paper clip out.
Hits: 582
Size: 64.24 KB
Posted: 3/8/06
When the regulator is in place and screws tightened, pull the paper clip out.		You will hear the brushes pop out of the housing.....and your done!
Hits: 609
Size: 66.17 KB
Posted: 3/8/06
You will hear the brushes pop out of the housing.....and your done!		 
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2022 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog