Doubler1.jpg 1452 hits | 60.79 KB | Posted: 3/27/05 First mockup of the doubler assembly.
Doubler2.jpg 1186 hits | 74.81 KB | Posted: 3/27/05 Detail of shifter area. The 205 has been converted for twin stick operation.
205Front.jpg 1187 hits | 63.66 KB | Posted: 3/27/05 The 205 half of the doubler adapter. The two halves will be welded together once the 205 clocking is...
205Close.jpg 1105 hits | 54.47 KB | Posted: 3/27/05 Closer shot of the 205 adapter.
203Back.jpg 1121 hits | 52.97 KB | Posted: 3/27/05 The 203 half of the adapter.
203Side.jpg 1023 hits | 57.06 KB | Posted: 3/27/05 That is one thick chunk of steel!
LinkageAdapters.jpg 1220 hits | 75.19 KB | Posted: 4/8/05 Closeup of adapters to hookup linkage and get the rods out of each others way.
TcaseLinkageTop.jpg 1136 hits | 75.92 KB | Posted: 4/8/05 This pic shows the alignment of the linkage pretty well.
TcaseLinkageTopFinished.jpg 1186 hits | 73.82 KB | Posted: 4/8/05 Linkage from top with finished shift arms.
TcaseLinkageSideFinished.jpg 1197 hits | 65.95 KB | Posted: 4/8/05 Linkage from the side with finished shift arms.
TcaseFinishedBeforePaint.jpg 1262 hits | 67.73 KB | Posted: 4/8/05 Ready to be painted (again) and reinstalled into the truck. The shift levers themselves will be fitt...
TcaseFront.jpg 1134 hits | 67.35 KB | Posted: 4/10/05 View from the front differential pinion.
TcasePassSide2.jpg 1080 hits | 66.81 KB | Posted: 4/10/05 View from pass side. No crossmembers yet.
TcasePassSide3.jpg 1044 hits | 71.72 KB | Posted: 4/10/05 Another passenger side view. Full size image is bigger.
ShifterHole.jpg 1362 hits | 59.43 KB | Posted: 4/10/05 All the shifters come through the stock hole.
BasicCrossmembers.jpg 1100 hits | 40.71 KB | Posted: 4/21/05 These are the basic crossmembers. A lot of stuff gets added to these.
205Mount.jpg 1002 hits | 56.13 KB | Posted: 4/21/05 Mount for NP205. The tranny mount is welded to the new 1/4 inch access cover, then the cover is atta...
TrannyMount.jpg 1084 hits | 60.06 KB | Posted: 4/21/05 The mount for the transmission.
TorqueMount.jpg 1214 hits | 75.17 KB | Posted: 4/21/05 The factory torque arm mount for the NP205.
Stabilizing tab.jpg 1139 hits | 47.72 KB | Posted: 4/21/05 With only a single bolt holding the crossmembers to the frame, the whole works wanted to collapse wh...
WholeTcaseAssy.jpg 1216 hits | 67.83 KB | Posted: 4/21/05 View of the whole assembly.
ShifterClearance.jpg 1091 hits | 59.32 KB | Posted: 4/21/05 Clearance between shifters and front crossmember.
DriveshaftClearance.jpg 1142 hits | 53.91 KB | Posted: 4/21/05 Clearance for front drivshaft through tunnel.
BellyClearance.jpg 1085 hits | 55.39 KB | Posted: 4/21/05 Clearance under the belly. A skidplate will be added.
RearCrossmember.jpg 1161 hits | 63.4 KB | Posted: 5/11/05 Finished rear crossmember. The skidplate mounting tabs have been added.
FinishedTrannyMount.jpg 1108 hits | 70.26 KB | Posted: 5/11/05 Gusseted tranny mount. Don't know if it will hold up with the bolts in shear. Time will tell.
Finished205Mount.jpg 1149 hits | 54.74 KB | Posted: 5/11/05 Gussetted 205 mount. Mounting bolts in shear on this one as well.
DriveLineInstalled.jpg 1310 hits | 80.35 KB | Posted: 7/18/05 I had an opportunity for this pic when I had the body off.
Doubler
