3096478_28_full.jpg
375 hits | 59.2 KB | Posted: 11/19/09
7-06-08: Here's the section of the 78 floor that I will be installing in the 54 cab.

3096478_66_full.jpg
355 hits | 58.36 KB | Posted: 11/19/09
10-02-08: Yesterday I finally started to do some more work on the 54. Didn't get much done but I go...

3096478_70_full.jpg
341 hits | 56.85 KB | Posted: 11/19/09
10-02-08: Here's a pic of the floor before I started to cut.

3096478_77_full.jpg
317 hits | 57.43 KB | Posted: 11/19/09
10-02-08: Today I started by lifting the cab and slid some 2"x2" steel tubes under the rockers to g...

3096478_71_full.jpg
350 hits | 66.08 KB | Posted: 11/19/09
10-02-08: I dug out my little Hobart plasma cutter and started cutting. Here's a couple pics of the ...

3096478_72_full.jpg
319 hits | 67.28 KB | Posted: 11/19/09
10-02-08:

3096478_73_full.jpg
339 hits | 55.42 KB | Posted: 11/19/09
10-02-08: And here's the entire floor cut out. Sorry the pics are a little dark ( it was getting dar...

3096478_74_full.jpg
347 hits | 51.61 KB | Posted: 11/19/09
10-02-08:

3096478_76_full.jpg
356 hits | 43.98 KB | Posted: 11/19/09
10-02-08:

3096478_78_full.jpg
391 hits | 64.92 KB | Posted: 11/19/09
10-03-08: Well here's today update.

I made up a cardboard template for the floor. Then I started t...

3096478_82_full.jpg
326 hits | 56.52 KB | Posted: 11/19/09
10-04-08: Well today I spent most of the day just trying to get to the 1/8" steel plate I had squir...

3096478_86_full.jpg
555 hits | 64.93 KB | Posted: 11/19/09
10-04-08:

3096478_83_full.jpg
386 hits | 65.47 KB | Posted: 11/19/09
10-04-08:

3096478_84_full.jpg
338 hits | 76.03 KB | Posted: 11/19/09
10-04-08:

3096478_85_full.jpg
342 hits | 63.91 KB | Posted: 11/19/09
10-04-08:

3096478_87_full.jpg
294 hits | 66.08 KB | Posted: 11/19/09
10-04-08: Then I did some measuring and a little trimming on the transmission tunnel. I did a littl...

3096478_90_full.jpg
268 hits | 57.24 KB | Posted: 11/19/09
10-10-08: Today I finally got a chance to start to weld the plates to the inner rockers. I started b...

30964780092_large.jpg
329 hits | 62.76 KB | Posted: 11/19/09
10-15-08: Today I did a little more work, Nothing major.

I brought out the grinders( one with ha...

30964780095_large.jpg
333 hits | 60.54 KB | Posted: 11/19/09
10-15-08:

3096478_91_full.jpg
299 hits | 60.74 KB | Posted: 11/19/09
10-10-08:

3096478_93_full.jpg
322 hits | 64.44 KB | Posted: 11/18/09
10-15-08:

3096478_96_full.jpg
285 hits | 67.18 KB | Posted: 11/18/09
10-15-08:

30964780094_large.jpg
262 hits | 69.52 KB | Posted: 11/19/09
10-15-08: I also started to lay out the rear crossmember that I'm fabricating to support the rear f...

3096478_98_full.jpg
356 hits | 72.08 KB | Posted: 11/18/09
10-16-08: Today I did some work on the floor.

I started out cleaning up the ends of the floor with...

3096478_99_full.jpg
302 hits | 71.26 KB | Posted: 11/18/09
10-16-08:

30964780100_large.jpg
283 hits | 68.6 KB | Posted: 11/19/09
10-16-08:

3096478_102_full.jpg
310 hits | 80.4 KB | Posted: 11/18/09
10-16-08: Here's a picture of the groove that the crossmember will sit in.

30964780103_large.jpg
323 hits | 73.42 KB | Posted: 11/19/09
10-16-08:

3096478_104_full.jpg
329 hits | 78.63 KB | Posted: 11/18/09
10-16-08:

3096478_106_full.jpg
311 hits | 70.57 KB | Posted: 11/18/09
10-16-08:

3096478_107_full.jpg
314 hits | 72.89 KB | Posted: 11/18/09
10-16-08:

30964780105_large.jpg
415 hits | 77.32 KB | Posted: 11/19/09
10-16-08: Next I cut out another small section of the floor. I did a little more welding. Then I b...

30964780108_large.jpg
328 hits | 69.48 KB | Posted: 11/19/09
10-16-08:

3096478_110_full.jpg
376 hits | 69.64 KB | Posted: 11/18/09
10-16-08: Then I decided to do one more test fit of the floor. Looks like it might work. I di...

30964780109_large.jpg
303 hits | 64.33 KB | Posted: 11/19/09
10-16-08:

3096478_111_full.jpg
332 hits | 69.68 KB | Posted: 11/18/09
10-21-08: I've been stuck working on everyones vehicles but my own the past few days. So today I ...

3096478_112_full.jpg
383 hits | 72.19 KB | Posted: 11/18/09
10-21-08:

3096478_113_full.jpg
294 hits | 68.56 KB | Posted: 11/18/09
10-21-08:

3096478_114_full.jpg
303 hits | 65.29 KB | Posted: 11/18/09
10-21-08:

3096478_115_full.jpg
335 hits | 70.97 KB | Posted: 11/18/09
10-21-08:Then I tried the floor section again.

It fits good so the next step is to start welding in...

3096478_116_full.jpg
283 hits | 68.79 KB | Posted: 11/18/09
10-21-08:

3096478_117_full.jpg
313 hits | 69.09 KB | Posted: 11/18/09
10-21-08:

3096478_118_full.jpg
318 hits | 68.02 KB | Posted: 11/18/09
10-21-08:

30964780119_large.jpg
261 hits | 54.97 KB | Posted: 11/19/09
10-25-08: Today I pulled the windshield out of the cab and tipped the cab on it's back panel. Then I...

3096478_120_full.jpg
303 hits | 80.49 KB | Posted: 11/18/09
10-25-08

3096478_123_full.jpg
309 hits | 66.44 KB | Posted: 11/18/09
10-29-08: Well after another small delay ( repairing another vehicle ) I'm back to work o...

3096478_124_full.jpg
294 hits | 71.56 KB | Posted: 11/18/09
10-29-08:

3096478_127_full.jpg
276 hits | 59.75 KB | Posted: 11/18/09
10-29-08: And here's after I cut it all out.

30964780128_large.jpg
298 hits | 62.42 KB | Posted: 11/19/09
10-29-08:

3096478_125_full.jpg
349 hits | 68.63 KB | Posted: 11/18/09
10-29-08: Then I flipped the rear floor section upside down and broke out the 7" craftsman sander w...

3096478_126_full.jpg
302 hits | 64.28 KB | Posted: 11/18/09
10-29-08:

3096478_130_full.jpg
297 hits | 72.59 KB | Posted: 11/19/09
10-29-08: Once the primer dried I set the floor back in the cab for the final time. I measured, squa...

3096478_131_full.jpg
298 hits | 66.26 KB | Posted: 11/19/09
10-29-08:

3096478_133_full.jpg
311 hits | 66.26 KB | Posted: 11/19/09
10-30-08: Well today I started out by doing a little measureing . I needed to extend the floor f...

3096478_134_full.jpg
328 hits | 64.85 KB | Posted: 11/19/09
10-30-08:

3096478_135_full.jpg
320 hits | 63.99 KB | Posted: 11/19/09
10-30-08: Then I started on the driverside.

3096478_137_full.jpg
285 hits | 79.9 KB | Posted: 11/19/09
10-30-08:

3096478_138_full.jpg
321 hits | 71.02 KB | Posted: 11/19/09
10-30-08:

3096478_136_full.jpg
321 hits | 61.66 KB | Posted: 11/19/09
10-30-08: Once they were welded in I went over both sides with the grinder. While I was at it I di...

3096478_139_full.jpg
407 hits | 65.77 KB | Posted: 11/19/09
10-30-08:

3096478_140_full.jpg
301 hits | 62.38 KB | Posted: 11/19/09
10-30-08:

3096478_141_full.jpg
298 hits | 69.02 KB | Posted: 11/19/09
10-30-08: Then I cut out the floor for the transmission tunnel.

3096478_142_full.jpg
302 hits | 60.41 KB | Posted: 11/19/09
10-30-08: I did a little test fit. I've got some more work to do on this!

I also broke out a sheet...

3096478_143_full.jpg
279 hits | 61.04 KB | Posted: 11/19/09
10-30-08:

3096478_144_full.jpg
361 hits | 67.02 KB | Posted: 11/19/09
10-30-08:

3096478_145_full.jpg
297 hits | 86.65 KB | Posted: 11/18/09
10-31-08: Thanks,

Here's today's progress.

I started out by pulling out the shear. I marked and dr...

3096478_146_full.jpg
224 hits | 63.37 KB | Posted: 11/18/09
10-31-08: Next I brought out the box with two 2'x4' sheets of diamond plate/tread/floor plate (wha...

3096478_147_full.jpg
241 hits | 72.62 KB | Posted: 11/18/09
10-31-08: I used the templates I made yesterday to mark out the cut lines. I started using the shea...

30964780151_large.jpg
287 hits | 70.27 KB | Posted: 11/19/09
10-31-08: I moved to the passenger side and welded it in.

30964780148_large.jpg
314 hits | 72.33 KB | Posted: 11/18/09
10-31-08: Then I welded the panel in.

3096478_149_full.jpg
346 hits | 74.35 KB | Posted: 11/18/09
10-31-08: I went over the weld beads quick with the grinder to clean them up a little. I'm going t...

3096478_150_full.jpg
286 hits | 67.03 KB | Posted: 11/18/09
10-31-08:

3096478_154_full.jpg
335 hits | 71.91 KB | Posted: 11/18/09
10-31-08: I cleaned up the welds a little.

It's starting to come together. I'm hoping to get a bi...

30964780155_large.jpg
319 hits | 71.69 KB | Posted: 11/19/09
10-31-08:

3096478_156_full.jpg
241 hits | 70.48 KB | Posted: 11/18/09
11-01-08: Well today I started out by making some templates for my rear filler panels. It took a co...

3096478_157_full.jpg
260 hits | 66 KB | Posted: 11/18/09
11-01-08:

3096478_158_full.jpg
299 hits | 68.7 KB | Posted: 11/18/09
11-01-08:

30964780159_large.jpg
369 hits | 68.14 KB | Posted: 11/19/09
11-01-08:

30964780160_large.jpg
334 hits | 75.34 KB | Posted: 11/19/09
11-03-08: I did the final trim on the rear floor section. I did some more trimming on the transmiss...

30964780163_large.jpg
302 hits | 54.76 KB | Posted: 11/19/09
11-03-08:

3096478_161_full.jpg
272 hits | 69.16 KB | Posted: 11/18/09
11-03-08: I also did a lot of clean up with a grinder, flap wheel and wire brush on the rear floor...

30964780164_large.jpg
269 hits | 64.3 KB | Posted: 11/19/09
11-03-08:

3096478_162_full.jpg
255 hits | 71.07 KB | Posted: 11/18/09
11-03-08:

30964780166_large.jpg
282 hits | 56.87 KB | Posted: 11/19/09
11-05-08: Today I welded the transmission tunnel in. It still needs a lot of work but it's welded in...

30964780165_large.jpg
290 hits | 65.82 KB | Posted: 11/19/09
11-05-08:

30964780167_large.jpg
293 hits | 60.87 KB | Posted: 11/19/09
11-05-08:

30964780170_large.jpg
321 hits | 53.73 KB | Posted: 11/18/09
2-23-09: And here's my poor cab that's sat outside all winter because I didn't get it in storage b...

30964780213_large.jpg
257 hits | 67.72 KB | Posted: 11/18/09
4-15-09: Well I've had a bunch of crap going on so I haven't had a chance to work on the 54 until to...

30964780216_large.jpg
288 hits | 59.15 KB | Posted: 11/19/09
4-15-09:

30964780217_large.jpg
301 hits | 63.85 KB | Posted: 11/19/09
4-15-09: Then I pulled out the rear diamond plate panels I made last year and checked their fit a...

30964780215_large.jpg
307 hits | 43.09 KB | Posted: 11/18/09
4-15-09:

30964780218_large.jpg
299 hits | 58.66 KB | Posted: 11/19/09
4-15-09:

30964780221_large.jpg
305 hits | 55.68 KB | Posted: 11/19/09
4-15-09:

30964780214_large.jpg
405 hits | 58.21 KB | Posted: 11/18/09
4-15-09: Next I cut out the cross brace I had in the cab. I didn't want to pull it until I had the...

30964780219_large.jpg
340 hits | 64.28 KB | Posted: 11/19/09
4-15-09: Last summer or fall I removed the original cab mounts and all the braces in the kick pane...

30964780220_large.jpg
270 hits | 50.01 KB | Posted: 11/19/09
4-15-09:

30964780222_large.jpg
250 hits | 57.36 KB | Posted: 11/19/09
4-15-09: My plan to take care of this is to weld in some 10 gauge steel plate. This will add s...

30964780224_large.jpg
283 hits | 60.79 KB | Posted: 11/21/09
4-15-09:

30964780223_large.jpg
269 hits | 57.79 KB | Posted: 11/19/09
4-15-09:

30964780225_large.jpg
370 hits | 62.11 KB | Posted: 11/19/09
4-15-09: I took the driver side plate did some test fitting, some grinding, a little cutting and g...

30964780226_large.jpg
306 hits | 49.93 KB | Posted: 11/19/09
4-16-09: Today I did a little more grinding to get to get the plate to fit better. I also figured ...

30964780227_large.jpg
282 hits | 47 KB | Posted: 11/19/09
4-16-09: After I got it cut out I cleaned up the cuts a little. Then I installed it back in the ca...

30964780228_large.jpg
322 hits | 67.34 KB | Posted: 11/19/09
4-16-09: I also noticed something today. There is a slight curve to the inside shape of the door p...

30964780229_large.jpg
266 hits | 59.3 KB | Posted: 11/19/09
4-16-09: Now that I had a hole in the plate I decided I should work on the cover for it. Any guess...

30964780230_large.jpg
323 hits | 56.91 KB | Posted: 11/19/09
4-16-09:

30964780231_large.jpg
373 hits | 66.44 KB | Posted: 11/19/09
4-17-09: Today went ok, almost.

I started by figuring out were I wanted to locate the mounting b...

30964780232_large.jpg
366 hits | 53.42 KB | Posted: 11/19/09
4-17-09:

30964780233_large.jpg
268 hits | 58.87 KB | Posted: 11/19/09
4-17-09: Next I pulled my template back out for the passenger side plate so I could figure out wh...

30964780234_large.jpg
288 hits | 57.1 KB | Posted: 11/19/09
4-17-09:

30964780235_large.jpg
281 hits | 73.41 KB | Posted: 11/22/09
5-03-09: Well after a bunch more delays I finally got some work done on the 54.

First I cut a s...

30964780236_large.jpg
241 hits | 66.83 KB | Posted: 11/19/09
5-03-09: I took the grinder to the bird poo welds and cleaned it up pretty good.

Next I needed ...

30964780237_large.jpg
274 hits | 60.04 KB | Posted: 11/19/09
5-03-09: While I was letting the primer dry I decided to repair the mistake I made the last time ...

30964780241_large.jpg
266 hits | 58.76 KB | Posted: 11/19/09
5-03-09: After the panel cooled down I sprayed the bare metal with some primer to slow down the ru...

30964780240_large.jpg
242 hits | 63.99 KB | Posted: 11/19/09
5-03-09: Now it was time to weld in the driver side kick panel plate. I clamped the panel in plac...

30964780238_large.jpg
280 hits | 78.46 KB | Posted: 11/19/09
5-03-09:

30964780242_large.jpg
293 hits | 39.18 KB | Posted: 11/19/09
5-03-09: Here's a few shots of it primed and with the diamond plate cover.

30964780243_large.jpg
292 hits | 55.11 KB | Posted: 11/19/09
5-03-09:

30964780244_large.jpg
303 hits | 65.87 KB | Posted: 11/19/09
5-03-09:

30964780245_large.jpg
290 hits | 70.55 KB | Posted: 11/19/09
5-03-09: Next on the list was to do some trimming to the new firewall recess/transmission tunnel....

30964780246_large.jpg
320 hits | 78.22 KB | Posted: 11/19/09
5-03-09:

30964780257_large.jpg
336 hits | 70.5 KB | Posted: 11/18/09
5-11-09: After working on the gauges I moved back to working on the firewall recess/ transmission t...

30964780256_large.jpg
268 hits | 76.28 KB | Posted: 11/18/09
5-17-09: After I pulled all the gauges back out and put them away I marked out the other panel for t...

30964780261_large.jpg
328 hits | 73.21 KB | Posted: 11/18/09
5-25-09: Yesterday I made up a little stand that I could clamp body panels to when I need to work o...

30964780262_large.jpg
292 hits | 64.31 KB | Posted: 11/18/09
5-25-09: I haven't done a whole lot of welding on sheet metal. I set up my welding according to the ...

30964780263_large.jpg
322 hits | 69.44 KB | Posted: 11/18/09
5-25-09: After I got the one side welded I did a quick pass with the grinder. Still need to do a lit...

30964780264_large.jpg
263 hits | 61.96 KB | Posted: 11/18/09
5-25-09: Then I welded the rest of it.

30964780265_large.jpg
297 hits | 72.44 KB | Posted: 11/18/09
5-25-09: After I finished the welding I started grinding down the welds. I still have a ways to go b...

30964780268_large.jpg
305 hits | 68.77 KB | Posted: 11/18/09
5-28-09:

30964780269_large.jpg
271 hits | 68.95 KB | Posted: 11/18/09
5-28-09:

30964780271_large.jpg
312 hits | 57.95 KB | Posted: 11/18/09
5-30-09: Well today I started out with the firewall looking like this.

30964780272_large.jpg
311 hits | 55.88 KB | Posted: 11/18/09
5-30-09: And the transmission tunnel looking like this.

30964780273_large.jpg
288 hits | 53.43 KB | Posted: 11/18/09
5-30-09: I cut out the 78 F250 transmission tunnel.

30964780274_large.jpg
253 hits | 60.14 KB | Posted: 11/18/09
5-30-09: Then I trimmed the rear floor a little. and cleaned up the left over welds from the old tr...

30964780276_large.jpg
265 hits | 62.31 KB | Posted: 11/18/09
5-30-09: Once the firewall was cut out I did some more fitting and got it ready to tack in place. I...

30964780277_large.jpg
294 hits | 77.44 KB | Posted: 11/18/09
5-30-09: Then I spent 3 or 4 hours doing some welding, then some grinding, more welding, more grin...

30964780278_large.jpg
292 hits | 78.26 KB | Posted: 11/18/09
5-30-09:

30964780280_large.jpg
282 hits | 68.66 KB | Posted: 11/18/09
5-30-09:

30964780282_large.jpg
293 hits | 70.45 KB | Posted: 11/18/09
5-30-09:

30964780283_large.jpg
343 hits | 78.58 KB | Posted: 11/18/09
5-30-09:

30964780281_large.jpg
308 hits | 76.59 KB | Posted: 11/18/09
5-30-09: Next on my "to do" list is to add a plate to the interior side of the driver side half of...

30964780284_large.jpg
310 hits | 59.13 KB | Posted: 11/18/09
6-5-09: I've been sick all week and haven't worked on the 54 at. Which sucks since the weather ...

54 Build - 4-3-10 030.JPG
378 hits | 101.56 KB | Posted: 4/3/10
4-3-10: It's back!! I had to dig something out of the garage so I decided to pull the cab b...

54 Build - 5-8-10 004.JPG
322 hits | 112.97 KB | Posted: 5/8/10
I took a short break from the scrap metal and worked on the 54 a little.

I decided I'm going to sta...

54 Build - 5-8-10 010.JPG
248 hits | 113.61 KB | Posted: 5/8/10
I'm not going have the cash for the diamond plate until sometime next month. But once I get it I'm g...

54 Build - 11-07-2010 002.JPG
256 hits | 93.02 KB | Posted: 11/7/10
11-07-2010: Today I had a couple hours to kill so I decided to do a little work on the 54 cab.

I ...

54 Build - 11-07-2010 004.JPG
297 hits | 96.6 KB | Posted: 11/7/10
11-07-2010:

54 Build - 11-07-2010 005.JPG
294 hits | 92.4 KB | Posted: 11/7/10
11-07-2010:

54 Build - 11-07-2010 006.JPG
291 hits | 103.84 KB | Posted: 11/7/10
11-07-2010:

54 Build - 11-07-2010 012.JPG
313 hits | 86.15 KB | Posted: 11/7/10
11-07-2010:

54 Build - 11-08-2010 014.JPG
303 hits | 102.12 KB | Posted: 11/8/10
11-08-2010: Today I did a little more test fitting on the main floor pan. Then I did a little more ...

54 Build - 11-08-2010 010.JPG
313 hits | 97.46 KB | Posted: 11/8/10
11-08-2010:

54 Build - 11-08-2010 003.JPG
305 hits | 102.01 KB | Posted: 11/8/10
11-08-2010:

54 Build - 11-08-2010 021.JPG
352 hits | 89.51 KB | Posted: 11/8/10
11-08-2010:

54 Build - 11-08-2010 024.JPG
375 hits | 87.57 KB | Posted: 11/8/10
11-08-2010:

54 Build - 11-08-2010 029.JPG
324 hits | 90.06 KB | Posted: 11/8/10
11-08-2010:

54 Build - 11-08-2010 023-2.jpg
293 hits | 87.22 KB | Posted: 11/8/10
11-08-2010: This picture shows what the recess panel is getting hung up on.

54 Build - 11-09-2010 005.JPG
303 hits | 81.94 KB | Posted: 11/9/10
11-09-2010: Today I started by cutting out more of the original firewall, my old firewall recess an...

54 Build - 11-09-2010 002.JPG
319 hits | 99.17 KB | Posted: 11/9/10

54 Build - 11-09-2010 011.JPG
351 hits | 95.86 KB | Posted: 11/9/10
11-09-2010: Then I made a template of the driver side kick panel plate so I'll be able to match it ...

54 Build - 11-09-2010 014.JPG
326 hits | 101.15 KB | Posted: 11/9/10
11-09-2010:

54 Build - 11-09-2010 003.JPG
348 hits | 105.31 KB | Posted: 11/9/10
11-09-2010:

54 Build - 11-09-2010 009.JPG
336 hits | 105.22 KB | Posted: 11/9/10
11-09-2010:

54 Build - 11-09-2010 007.JPG
337 hits | 99.8 KB | Posted: 11/9/10
11-09-2010:

54 Build - 11-10-2010 002.JPG
310 hits | 97.7 KB | Posted: 11/10/10
11-10-2010: Today I got the other two panels welded in. My welds are slowly getting a little bette...

54 Build - 11-10-2010 005.JPG
312 hits | 97.87 KB | Posted: 11/10/10
11-10-2010:

54 Build - 11-10-2010 008.JPG
371 hits | 89.95 KB | Posted: 11/10/10
11-10-2010:

54 Build - 11-10-2010 010.JPG
355 hits | 97.4 KB | Posted: 11/10/10
11-10-2010: The flat vertical panel on the firewall recess is where I'm going to be mounting my han...

54 Build - 11-10-2010 017.JPG
385 hits | 101.82 KB | Posted: 11/10/10
11-10-2010: I left the floor toe board section a little long just so I made sure I had enough mater...

54 Build - 11-10-2010 019.JPG
466 hits | 92.3 KB | Posted: 11/10/10
11-10-2010:

54 Build - 11-10-2010 027.JPG
394 hits | 88.12 KB | Posted: 11/10/10
11-10-2010:

54 Build - 11-10-2010 035.JPG
280 hits | 93.36 KB | Posted: 11/10/10
11-10-2010: The part of my transmission tunnel panel that is sticking up above the existing transmi...

54 Build - 3-30-2011 012.JPG
308 hits | 92.11 KB | Posted: 4/2/11
4-2-2011: I did a little work on the 54 today. But mainly I spent a lot of time staring at it tryi...

54 Build - 3-30-2011 009.JPG
256 hits | 93.22 KB | Posted: 4/2/11
4-2-2011:

54 Build - 3-30-2011 020.JPG
279 hits | 108.03 KB | Posted: 4/2/11
4-2-2011:

54 Build - 3-30-2011 019.JPG
285 hits | 101.55 KB | Posted: 4/2/11
4-2-2011:

54 Build - 3-30-2011 017.JPG
314 hits | 84.51 KB | Posted: 4/2/11
4-2-2011: Since I'm not using the stock heater I'm going to remove the louvered section on the passe...

54 Build - 4-2-2011 009.JPG
277 hits | 86.8 KB | Posted: 4/2/11
4-2-2011: I got the louvered section of the cab cowl side panel cut out.

54 Build - 4-2-2011 008.JPG
277 hits | 100.2 KB | Posted: 4/2/11
4-2-2011: I got a good start on the filler panel. I had some pieces of the original flamed hood ( I ...