IMG_20200710_133414.jpg
63 hits | 51.15 KB | Posted: 7/13/20
20200710 - Pulled the rear seat out. Lot's of space... having trouble unbolting the three mounts fro...

IMG_20200715_181948.jpg
102 hits | 66.08 KB | Posted: 7/16/20
20200715 - Passenger seat came out surprisingly easy. Unplug the cable connecting to the bottom, the...

IMG_20200715_183123.jpg
52 hits | 70.48 KB | Posted: 7/16/20
20200715 - Center console comes out with three 10mm bolts. It also came out pretty easily.

IMG_20200715_185537.jpg
62 hits | 54.82 KB | Posted: 7/16/20
20200715 - Driver's seat came out tough. I ended up shearing off two of the four 15mm bolts getting ...

IMG_20200715_190054.jpg
52 hits | 59.69 KB | Posted: 7/16/20
20200716 - Pretty spacious without seats. This is going to require a lot of sound deadening material...

IMG_20200715_191432.jpg
52 hits | 33.01 KB | Posted: 7/16/20
20200715 - All of the rest of the interior is more or less layered over the top of each other, and n...

IMG_20200715_191340.jpg
47 hits | 39.84 KB | Posted: 7/16/20
20200715 - Next is the long piece that runs along the bottom of the hard-top window. It's secured by...

IMG_20200715_191740.jpg
69 hits | 34.85 KB | Posted: 7/16/20
20200715 - This is what the trim clips are hooking into to hold the trim below the hard-top window. ...

IMG_20200715_191810.jpg
54 hits | 40.45 KB | Posted: 7/16/20
20200715 - The next piece I removed was this trim piece at the back of the hard top running vertical...

IMG_20200715_192617.jpg
46 hits | 51.54 KB | Posted: 7/16/20
20200715 - Next is the trim over the front driver and passenger windows (3-4 screws each) followed b...

IMG_20200715_194424.jpg
55 hits | 27.39 KB | Posted: 7/16/20
20200715 - The seatbelt needs to come off for the B pillar trim to come out. It requires a t50 torx ...

IMG_20200715_194825.jpg
45 hits | 69.34 KB | Posted: 7/16/20
20200715 - Passenger seatbelt top bolt removed. It has some carpet-padding-like material between the...

IMG_20200715_195333.jpg
50 hits | 58.03 KB | Posted: 7/16/20
20200715 - Made some pretty good progress. I have quite a bit more to go, though.

IMG_20200715_194901.jpg
48 hits | 36.93 KB | Posted: 7/16/20
20200715 - The B pillar looks like it has dirty water streaks from the seam.

IMG_20200715_194840.jpg
47 hits | 21.09 KB | Posted: 7/16/20
20200715 - Passnger B pillar seam shows evidence of leaking.

IMG_20200715_195243.jpg
54 hits | 29.08 KB | Posted: 7/16/20
20200715 - Driver B pillar seam shows evidence of leaking. Also, the gap in the seam is much bigger ...

IMG_20200718_093456.jpg
58 hits | 28.4 KB | Posted: 7/18/20
20200718 - The rear seat belts will have to come out completely since I can't get the side trim off ...

IMG_20200718_093508.jpg
56 hits | 33.11 KB | Posted: 7/18/20
20200718 - With the seatbelt bolts removed, the side trim can be easily removed. Be aware there is a...

IMG_20200718_124502.jpg
49 hits | 37.76 KB | Posted: 7/18/20
20200718 - One of the three T50 torx bits I broke trying to get the driver side bed bolt out.

IMG_20200718_150136.jpg
48 hits | 56.38 KB | Posted: 7/18/20
20200718 - After getting the carpets out, there was just a lot of vacuuming and wiping down to do. 2...

IMG_20200718_150131.jpg
45 hits | 65.34 KB | Posted: 7/18/20
20200718 - Progression of cleaning, laying out the first stage of sound deadening (CLD tiles), and a...

IMG_20200718_150203.jpg
46 hits | 66.43 KB | Posted: 7/18/20
20200718 - Progression of cleaning, laying out the first stage of sound deadening (CLD tiles), and a...

IMG_20200718_154015.jpg
52 hits | 77.03 KB | Posted: 7/18/20
20200718 - Progression of cleaning, laying out the first stage of sound deadening (CLD tiles), and a...

IMG_20200718_155409.jpg
45 hits | 75.12 KB | Posted: 7/18/20
20200718 - Progression of cleaning, laying out the first stage of sound deadening (CLD tiles), and a...

IMG_20200718_160234.jpg
51 hits | 73.98 KB | Posted: 7/18/20
20200718 - Progression of cleaning, laying out the first stage of sound deadening (CLD tiles), and a...

IMG_20200718_164137.jpg
64 hits | 72.67 KB | Posted: 7/18/20
20200718 - Progression of cleaning, laying out the first stage of sound deadening (CLD tiles), and a...

IMG_20200718_160326.jpg
50 hits | 63.89 KB | Posted: 7/18/20
20200718 - Progression in the front of cleaning, laying out the first stage of sound deadening (CLD ...

IMG_20200718_164146.jpg
57 hits | 58.17 KB | Posted: 7/18/20
20200718 - Progression in the front of cleaning, laying out the first stage of sound deadening (CLD ...

IMG_20200719_130239.jpg
62 hits | 64.42 KB | Posted: 7/19/20
20200719 - Pulled the headliner off so I could get the roof done. These visors are a pain in the ass...

IMG_20200719_130244.jpg
46 hits | 52.46 KB | Posted: 7/19/20
20200719 - The visors notch into this hole and twist to more or less lock them in place on top of th...

IMG_20200719_130250.jpg
49 hits | 56.08 KB | Posted: 7/19/20
20200719 - You can see the bit that notches into the roof and the spring assembly that goes into the...

IMG_20200719_130301.jpg
51 hits | 41.26 KB | Posted: 7/19/20
20200719 - The headliner is held up by the center console, a plastic trim clip, one over the driver ...

IMG_20200719_130936.jpg
51 hits | 50.13 KB | Posted: 7/19/20
20200719 - I cleaned the roof and applied the CLD tiles.

IMG_20200719_133643.jpg
54 hits | 47.69 KB | Posted: 7/19/20
20200719 - Used 3m spray high strength 90 spray cement on this Hydrophobic Melamine Foam (HMF) as th...

IMG_20200719_163300.jpg
69 hits | 71.42 KB | Posted: 7/19/20
20200719 - Putting the headliner back up by yourself is kind of tough. Getting it aligned with the H...

IMG_20200719_163313.jpg
54 hits | 42 KB | Posted: 7/19/20
20200719 - It was 105 degrees today so I had to quit after trimming up this first piece. Lots of pla...

IMG_20200815_125733.jpg
48 hits | 47.18 KB | Posted: 8/15/20
20200815 - Reinstalled the front trim at the top of the windshield. I put a bit of HMF on the back t...

IMG_20200815_131414.jpg
45 hits | 54.47 KB | Posted: 8/15/20
20200815 - Started fitting MLV in the cargo area driver wheel well.

IMG_20200815_134846.jpg
54 hits | 40.01 KB | Posted: 8/15/20
20200815 - Started cementing the MLV in the cargo area driver wheel well.

IMG_20200815_144259.jpg
51 hits | 35.85 KB | Posted: 8/15/20
20200815 - Started cementing the MLV in the cargo area driver wheel well.

IMG_20200815_153921.jpg
44 hits | 39.24 KB | Posted: 8/15/20
20200815 - Cementing CCF to the MLV in the inner quarter panel

IMG_20200815_160827.jpg
46 hits | 38.29 KB | Posted: 8/15/20
20200815 - Cementing the MLV in the inner quarter panel

IMG_20200815_160843.jpg
42 hits | 65.55 KB | Posted: 8/15/20
20200815 - Cementing the MLV in the inner quarter panel

IMG_20200815_162356.jpg
49 hits | 32.35 KB | Posted: 8/15/20
20200815 - Cementing the HMF in the inner quarter panel

IMG_20200815_162412.jpg
45 hits | 56.18 KB | Posted: 8/15/20
20200815 - Cementing the MLV in the inner quarter panel

IMG_20200815_172051.jpg
50 hits | 55.28 KB | Posted: 8/15/20
20200815 - More MLV and CCF on the cargo floor.

IMG_20200816_130041.jpg
54 hits | 41.43 KB | Posted: 8/16/20
20200816 - Started putting down MLV and CCF on the passenger side quarter and wheel well.

IMG_20200816_161533.jpg
54 hits | 40.97 KB | Posted: 8/16/20
20200816 - Started putting down MLV and CCF on the passenger side quarter and wheel well.

IMG_20200816_163917.jpg
43 hits | 73.8 KB | Posted: 8/16/20
20200816 - Replacing the 6 rear seat bolts with grade 8 stainless.

IMG_20200816_163922.jpg
43 hits | 59.76 KB | Posted: 8/16/20

IMG_20200816_183008.jpg
42 hits | 52.74 KB | Posted: 8/16/20
20200816 - Drilled through the sound deadening to place the bolts. Half of them won't thread and I'm...

IMG_20200816_183015.jpg
46 hits | 66.67 KB | Posted: 8/16/20
20200816 - Foam on the rear speakers disintegrated, so I replaced it with CCF.

IMG_20200816_190338.jpg
47 hits | 54.1 KB | Posted: 8/16/20
20200816 - Passenger side is complete. Time for new flooring and putting the trim back on.

IMG_20200816_191210.jpg
45 hits | 42.99 KB | Posted: 8/16/20
20200816 - Passenger side wheel well vinyl placed. Might need to heatgun it to get it to lay out fla...

IMG_20200818_165226.jpg
44 hits | 49.18 KB | Posted: 8/20/20
20200818 - Finished up CCF and MLV on the driver side cargo area.

IMG_20200818_172922.jpg
46 hits | 42.33 KB | Posted: 8/20/20
20200818 - And HMF on the driver side cargo area.

IMG_20200818_173711.jpg
51 hits | 53.02 KB | Posted: 8/20/20
20200818 - Cargo area sound deadening is finished.

IMG_20200820_112033.jpg
54 hits | 51.88 KB | Posted: 8/20/20
20200820 - I started applying the new vinyl flooring I purchased from Bronco Graveyard (been sitting...

IMG_20200821_104226.jpg
54 hits | 48.48 KB | Posted: 8/23/20
20200821 - Started laying CCF and MLV in the cabin area.

IMG_20200821_113331.jpg
43 hits | 58.21 KB | Posted: 8/23/20
20200821 - Needed heavy boxes to keep the MLV down on the bit that attached the cargo area to the ca...

IMG_20200821_113343.jpg
50 hits | 50.86 KB | Posted: 8/23/20
20200821 - Needed heavy boxes to keep the MLV down on the bit that attached the cargo area to the ca...

IMG_20200821_114812.jpg
47 hits | 47.49 KB | Posted: 8/23/20
20200821 - Used industrial velcro to keep the MLV tight to the dropoff from the cargo area and help ...

IMG_20200821_121551.jpg
53 hits | 52.38 KB | Posted: 8/23/20
20200821 - Much easier to drill holes and cut holes through the CCF and vinyl one layer at a time, r...

IMG_20200821_134003.jpg
47 hits | 56.2 KB | Posted: 8/23/20
20200821 - More CCF down for the rest of the floor in the cabin.

IMG_20200821_153121.jpg
40 hits | 48.57 KB | Posted: 8/23/20
20200821 - Putting MLV on this one elevated place under the center console took forever. Lots of cut...

IMG_20200822_081545.jpg
43 hits | 88.68 KB | Posted: 8/23/20
20200822 - These instructions are bull. I did this and it still doesn't form correctly. Heat gun was...

IMG_20200822_093010.jpg
46 hits | 35.09 KB | Posted: 8/23/20
20200822 - Finally finished the transmission hump

IMG_20200822_093032.jpg
51 hits | 55.27 KB | Posted: 8/23/20
20200822 - Second view of the finished transmission hump. Lot's of velcro used here to keep the cont...

IMG_20200822_112820.jpg
109 hits | 52.36 KB | Posted: 8/23/20
20200822 - I had excess CCF, so I put it over the top of the sound deadening vinyl, and under the fl...

IMG_20200822_135924.jpg
57 hits | 73.5 KB | Posted: 8/23/20
20200822 - Starting to reinstall some trim. I had to install and uninstall several times to perfect ...

IMG_20200822_140140.jpg
48 hits | 66.54 KB | Posted: 8/23/20
20200822 - Padding removed from behind the pocket on the side panel.

IMG_20200822_140441.jpg
53 hits | 58.4 KB | Posted: 8/23/20
20200822 - Also reinstalled the mounts for the rear seat amongst this disaster of tools and things.

IMG_20200822_150245.jpg
56 hits | 54.2 KB | Posted: 8/23/20
20200822 - Completed reinstalling some trim and mounts in the cargo area.

IMG_20200822_155237.jpg
44 hits | 56.76 KB | Posted: 8/23/20
20200822 - Padding came with the cabin flooring, so I positioned and trimmed it as necessary and use...

IMG_20200822_170735.jpg
52 hits | 53.25 KB | Posted: 8/23/20
20200822 - The front flooring required a massive amount of trimming, refuses to let me get the creas...

IMG_20200822_204036.jpg
114 hits | 48.6 KB | Posted: 8/23/20
20200822 - Preview of my struggles getting the F250 reupholstered 40/20/40 seats and seatbelts in. I...

IMG_20200823_125353.jpg
51 hits | 44.46 KB | Posted: 8/23/20
20200823 - After a metric F***load of finagling and forcing, I was able to get the seats to bolt up ...

IMG_20200823_125402.jpg
51 hits | 57.62 KB | Posted: 8/23/20
20200823 - I still have more heatgun treatments to do on the floor, more trimming to do, and some mo...