20200613_161505.jpg
66 hits | 80.31 KB | Posted: 7/24/22
The undercarriage shows no signs of off-roading or modification.
(Posted in: Just Teasing)

20200905_162522.jpg
60 hits | 90.55 KB | Posted: 7/24/22
The fuel filter was among the first things changed, but it was a MotorCraft.
(Posted in: Just Teasing)

20200905_181729.jpg
56 hits | 100.29 KB | Posted: 7/24/22
Most of the cruise buttons were broken away, so they got replaced with new.
(Posted in: Just Teasing)

20200906_123453.jpg
60 hits | 141.16 KB | Posted: 7/24/22
The oil leaks were coming from the VCGs, so they both got changed. So was the PCV valve.
(Posted in: Just Teasing)

20200906_144127.jpg
66 hits | 95.97 KB | Posted: 7/24/22
The oil leaks were coming from the VCGs, so they both got changed.
(Posted in: Just Teasing)

20200908_140827.jpg
60 hits | 73.72 KB | Posted: 7/24/22
The spark plugs were OK, but got changed anyway. The right side was a nightmare.
(Posted in: Just Teasing)

20200905_195859.jpg
62 hits | 72.15 KB | Posted: 7/24/22
The air filter either wasn't installed right, or was left in too long because the fresh-air duct & TB were dusty. Both got cleaned.
(Posted in: Just Teasing)

20200910_104406.jpg
59 hits | 112.12 KB | Posted: 7/24/22
The rear door cables were shot (as usual), but I wasn't expecting the inside to be THIS dusty. Turns out, the whole truck was, but the visible surfaces got cleaned very well.
(Posted in: Just Teasing)

20200908_111349.jpg
61 hits | 91.01 KB | Posted: 7/24/22
The common RV mirror was swapped to an autodimming compass version.
(Posted in: Just Teasing)

20200613_155803.jpg
57 hits | 57.94 KB | Posted: 7/24/22
The center registers were broken, so after MUCH searching, a new Ford bezel (5L5Z-1004302-GAB) was installed. Later, the cigar lighter was swapped to a dual-USB voltmeter.
(Posted in: Just Teasing)

20200908_161058.jpg
78 hits | 106.39 KB | Posted: 7/24/22
Pulling the RV mirror wiring required removing the cluster bezel & knee bolster. The quantity of dust was amazing.
(Posted in: Just Teasing)

20210921_160919.jpg
85 hits | 90.7 KB | Posted: 7/24/22
Instead of crossing the bridge & going around the curve, the truck came to rest on its side on the rocks, a few feet from the water's edge. The driver's doors hit the black pipe after the truck had flipped in the air. It's amazing that neither occupa...
(Posted in: Just Teasing)

20220720_163223.jpg
191 hits | 46.12 KB | Posted: 7/24/22
The last time it was here, it looked like-new.
IF THE IMAGE IS TOO SMALL, click it.

Surprisingly, I drove it onto & off of the trailer, with the A/C working, and no CEL.

[url=https://www.rockauto.com/en/catalog/ford,2003,ranger,4.0l v6,1438311]Rock...
(Posted in: Unrolling)

20220720_163729.jpg
195 hits | 63.94 KB | Posted: 7/24/22
I think this is repairable...
IF THE IMAGE IS TOO SMALL, click it.
(Posted in: Unrolling)

20220720_174803.jpg
183 hits | 119.55 KB | Posted: 7/24/22
It took less than an hour to get the bed off.
IF THE IMAGE IS TOO SMALL, click it.
(Posted in: Unrolling)

20220720_174955.jpg
122 hits | 82.47 KB | Posted: 7/24/22
It's still amazing how dusty this truck is.
IF THE IMAGE IS TOO SMALL, click it.
(Posted in: Unrolling)

20220721_144407.jpg
218 hits | 122.01 KB | Posted: 7/24/22
The LHF A-arm is severely twisted, but a new Ford 7L5Z-3079-A (aka Motorcraft MCSOE45) is on the way. The wrecker driver who pulled the truck out of the c...
(Posted in: Unrolling)

20220722_195910.jpg
172 hits | 129.95 KB | Posted: 7/24/22
The oppressive heat has slowed me down, but it's getting close. Right now, it's still drivable with A/C & no CEL.
(Posted in: Unrolling)

20220729_155049.jpg
227 hits | 141.12 KB | Posted: 7/29/22
After pulling the LHF suspension off, I found the steering knuckle bent through the upper caliper bolt hole. The torsion key pad isolator (6L5Z5b335AA) is degrade...
(Posted in: Unrolling)

20220727_171713.jpg
202 hits | 105.43 KB | Posted: 7/29/22
The replacement lower A-arm (MCSOE45) arrived, but I can't install it until I get a steering knuckle & torsion key pad, and swap the [url=https://www.amazon.c...
(Posted in: Unrolling)

20220728_095755.jpg
115 hits | 125.06 KB | Posted: 7/30/22
I sandblasted the torsion key & pad, and painted them with graphite.
IF THE IMAGE IS TOO SMALL, click it.
(Posted in: Unrolling)

20220801_114241.jpg
129 hits | 133.59 KB | Posted: 8/1/22
The right outer CV boot is torn & twisted, so that side came apart. I'm sandblasting & painting most of the parts that come off.
IF THE IMAGE IS TOO SMALL, click it.
(Posted in: Unrolling)

20220801_185630.jpg
207 hits | 139.11 KB | Posted: 8/1/22
The cab is empty now, and ready to come off.
(Posted in: Unrolling)

BrakesDrum.jpg
138 hits | 80.83 KB | Posted: 9/7/22
While so much was apart, I decided to clean up the rear brakes. Good thing, since I found 2 Right autoadjusters had been installed. So while waiting for a Left kit (Motorcraft BRAK2662A) to arrive, I sa...
(Posted in: Unrolling)

20220824_141205.jpg
142 hits | 138.67 KB | Posted: 9/7/22
At the same time as the brakes, I tracked down a couple of used wheels, bought 2 new tires (Cooper AT3 265/70R16), and had TPMS sensors installed in the 4...
(Posted in: Unrolling)

Knuckles.jpg
144 hits | 96.17 KB | Posted: 9/7/22
While browsing the JYs for some matching Aluminum wheels, I found a 4WD left knuckle on an '02 Ranger. After sandblasting, I painted it & the hub. The original upper ball joint seems OK, and the replacement [url=https://www.rockauto.com/en/moreinfo.p...
(Posted in: Unrolling)

BootF5TZ3A331A.jpg
141 hits | 60.59 KB | Posted: 9/7/22
Replacing the torn right CV boot was messy, but much easier than I expected.
IF THE IMAGE IS TOO SMALL, click it.
(Posted in: Unrolling)

TRE-LHI.jpg
143 hits | 59.12 KB | Posted: 9/7/22
The first replacement part to go on the left side was the inner tie rod end. The booger-weld that allowed it to be driven after being broken in the wreck also prevented the (undamaged) boot from sliding...
(Posted in: Unrolling)

Knucklehead.jpg
144 hits | 67.42 KB | Posted: 9/7/22
After reinstalling the tie rod end, A-arm, knuckle, & hub, I tried to put the brakes back on so I could roll the chassis. But the caliper bolts wouldn't line up...
IF THE IMAGE IS TOO SMALL, click it.

I knew the rotor hadn't grown, which only lef...
(Posted in: Unrolling)

Bends.jpg
149 hits | 98.03 KB | Posted: 9/7/22
With the tie rod end, sway bar end link, A-arm, & knuckle replaced, I tried to install the (straight) torsion bar. But it didn't align with its pocket under the frame rail, indicating the frame is bent. So I pried the end of the bar into place and bo...
(Posted in: Unrolling)

20220901_175242.jpg
156 hits | 137.04 KB | Posted: 9/7/22
It's near the shadow of the engine, but the left frame rail is bent inward.
IF THE IMAGE IS TOO SMALL, click it.
(Posted in: Unrolling)

FrameClean.jpg
155 hits | 55.71 KB | Posted: 9/7/22
After rolling the cab off, I rinsed the frame. But later, I had to remove the gas tank heat shield to get a lot more mud & gravel out.
IF THE IMAGE IS TOO SMALL, click it.
(Posted in: Unrolling)