|
|
Hits: 1648
Size: 63.8 KB
Posted: 7/7/04
Reinstalling lifters | 
Hits: 1320
Size: 54.35 KB
Posted: 7/7/04
| 
Hits: 1434
Size: 60.34 KB
Posted: 7/7/04
Lifters installed. | 
Hits: 1301
Size: 55.68 KB
Posted: 7/7/04
Close-up of bores (getting ready to install head gaskets). | 
Hits: 1258
Size: 55.8 KB
Posted: 7/7/04
|
Hits: 1312
Size: 57.26 KB
Posted: 7/7/04
Installing head gaskets. | 
Hits: 1439
Size: 58.76 KB
Posted: 7/7/04
Not exactly a perfect circle in these gaskets! | 
Hits: 1279
Size: 59.08 KB
Posted: 7/7/04
Installing newly re-worked heads. | 
Hits: 1489
Size: 58.26 KB
Posted: 7/7/04
These are not exactly lightweight! | 
Hits: 1427
Size: 67.5 KB
Posted: 7/27/04
Reinstalling the pushrods |
Hits: 1277
Size: 56.62 KB
Posted: 7/27/04
Close-up of the ported exhaust ports | 
Hits: 1304
Size: 65.78 KB
Posted: 7/27/04
Another view of the newly ported exhaust ports | 
Hits: 1283
Size: 68.6 KB
Posted: 7/27/04
Removing duct tape from the intake side of the heads to prepare for the intake installation. | 
Hits: 1250
Size: 64.4 KB
Posted: 7/27/04
More tape removal. | 
Hits: 1232
Size: 60.38 KB
Posted: 7/27/04
Heads are installed on the 390. |
Hits: 1296
Size: 65.76 KB
Posted: 7/27/04
Closer view of the 390 topend. | 
Hits: 1365
Size: 59.48 KB
Posted: 7/27/04
Close-up of the valve springs. The new exhaust valves have nice straight edges on them (no more mus... | 
Hits: 1378
Size: 57.09 KB
Posted: 7/27/04
Side view of the topened sans intake. | 
Hits: 1336
Size: 68.84 KB
Posted: 7/27/04
Torquing the heads to spec. | 
Hits: 1521
Size: 62.49 KB
Posted: 7/27/04
Fel-Pro gaskets used with a bead of RTV at the corners to prevent oil leaks. NOTE- my 390 burns oil... |
Hits: 1412
Size: 63.8 KB
Posted: 7/27/04
Close-up of the RTV at the corner of the gaskets. | 
Hits: 1433
Size: 70.5 KB
Posted: 7/27/04
Getting ready for the intake install. | 
Hits: 1345
Size: 65.39 KB
Posted: 7/27/04
All gaskets are installed. | 
Hits: 1269
Size: 56.26 KB
Posted: 7/27/04
Bottom-side view of the Performer RPM intake that's ready for installation. | 
Hits: 1332
Size: 71.37 KB
Posted: 7/27/04
Strategically aligning the intake with the water pump. |
Hits: 1311
Size: 63.62 KB
Posted: 7/27/04
Intake & carb in place, ready to tighten. | 
Hits: 1239
Size: 70.17 KB
Posted: 7/27/04
Hand tightening the intake prior to properly torquing with a torque wrench. | 
Hits: 1279
Size: 58.94 KB
Posted: 7/27/04
Installing valvetrain | 
Hits: 1291
Size: 70.9 KB
Posted: 7/27/04
Another valvetrain install pic. Too bad I don't have clear valve covers, these look really nice whe... | 
Hits: 1221
Size: 67.4 KB
Posted: 7/27/04
Hand-tightening the valvetrain prior to proper torquing with a torque wrench. |
Hits: 1330
Size: 66.41 KB
Posted: 7/27/04
Another shot of fthe valvetrain installed. | 
Hits: 1407
Size: 60.55 KB
Posted: 7/27/04
Torquing the valvetrain to spec. | 
Hits: 1338
Size: 59.68 KB
Posted: 7/27/04
Topened assembled -- ready for distributor. | 
Hits: 1360
Size: 67.66 KB
Posted: 7/27/04
Close-up of the installed distributor. | 
Hits: 1396
Size: 59.82 KB
Posted: 7/27/04
Topend ready-to-install. |
Reassembling topend