357 finishing up 002.jpg
887 hits | 68.16 KB | Posted: 10/17/03
I was looking for a tranny dipstick, but I found this bigger factory cooler from a F250 instead

357 finishing up 001.jpg
851 hits | 75.86 KB | Posted: 10/17/03
This is the little baby factory one

357 finishing up 004.jpg
903 hits | 74.65 KB | Posted: 10/17/03
big one bolts into the factory holes...I flipped the samll one over to use as a PS cooler

357 finishing up 007.jpg
855 hits | 87.68 KB | Posted: 10/17/03
I will plumb this one in, and get rid of the tube cooler

357 finishing up 008.jpg
857 hits | 74.43 KB | Posted: 10/17/03
Cant even see the change behind the grille

357 finishing up 009.jpg
935 hits | 87.82 KB | Posted: 10/17/03
Rear veiw...cool...er..cooler

357 finishing up 010.jpg
879 hits | 70.9 KB | Posted: 10/17/03
One valve cover

357 finishing up 012.jpg
884 hits | 86.57 KB | Posted: 10/17/03
Second valve cover after fighting with the tranny dipstick for a long time

357 finishing up 013.jpg
907 hits | 87.75 KB | Posted: 10/17/03
I set the intake on to see how it fits

357 finishing up 014.jpg
930 hits | 85.13 KB | Posted: 10/17/03
Looks very cool

357 finishing up 015.jpg
1022 hits | 66.43 KB | Posted: 10/17/03
It hits on the firewall

357 finishing up 016.jpg
1021 hits | 90.04 KB | Posted: 10/17/03
Very cool

357 finishing up 017.jpg
1064 hits | 95.28 KB | Posted: 10/18/03
Put the main engine harness on first thing today, then the fuel injectors and fuel rail

357 finishing up 018.jpg
1128 hits | 102.42 KB | Posted: 10/18/03
Hooked up the fuel lines, and the heater hose ECT thingie

357 finishing up 019.jpg
893 hits | 90.76 KB | Posted: 10/18/03
Other side

357 finishing up 020.jpg
902 hits | 102.73 KB | Posted: 10/18/03
Distributor is in

357 finishing up 021.jpg
912 hits | 94.42 KB | Posted: 10/18/03
Now the new water pump

357 finishing up 022.jpg
917 hits | 98.03 KB | Posted: 10/19/03
Alternator bracket setup is on

357 finishing up 023.jpg
955 hits | 101.03 KB | Posted: 10/19/03
Other side

357 finishing up 024.jpg
960 hits | 90.95 KB | Posted: 10/19/03
Coil setup raised, cleaned, painted, and mounted

357 finishing up 025.jpg
896 hits | 96.28 KB | Posted: 10/19/03
See the 1" spacer on the mounts...needed to clear the valve covers

357 finishing up 026.jpg
956 hits | 70.31 KB | Posted: 10/19/03
Still touches...more work to do

357 finishing up 027.jpg
1043 hits | 90.89 KB | Posted: 10/19/03
Upper manifold is mounted

357 finishing up 028.jpg
963 hits | 72.07 KB | Posted: 10/19/03
Just clears

357 finishing up 030.jpg
957 hits | 84.17 KB | Posted: 10/19/03
Side shot

357 finishing up 033.jpg
952 hits | 105.51 KB | Posted: 10/19/03
Lot of wires on this thing

357 finishing up 037.jpg
926 hits | 85.9 KB | Posted: 10/20/03
We cut off the coolant tubes for the throttle body

357 finishing up 040.jpg
939 hits | 88.28 KB | Posted: 10/20/03
PS bracket detailed and installed

357 finishing up 041.jpg
964 hits | 105.67 KB | Posted: 10/20/03
Plug wires are on, and linkage is hooked up

357 finishing up 045.jpg
962 hits | 89.9 KB | Posted: 10/20/03
Non-smog pump belt routing

357 finishing up 046.jpg
959 hits | 96.5 KB | Posted: 10/20/03
Front veiw...almost done

357 finishing up 048.jpg
958 hits | 90.73 KB | Posted: 10/20/03
All ready to fire it up

357 finishing up 049.jpg
916 hits | 91.74 KB | Posted: 10/20/03
We ran it, no exhaust, just the headers...wow..LOUD.

357 finishing up 058.jpg
872 hits | 94.1 KB | Posted: 10/23/03
I drilled and assembled the pod and wiring on the bench....Dont do this.

357 finishing up 059.jpg
822 hits | 104.45 KB | Posted: 10/23/03
Doing the wiring is ok, but dont mount the pod yet

357 finishing up 062.jpg
897 hits | 87.47 KB | Posted: 10/23/03
I also ran all the wires together, another waste of time

357 finishing up 063.jpg
872 hits | 80.8 KB | Posted: 10/23/03
Trial fitting the Pod

357 finishing up 065.jpg
815 hits | 63.5 KB | Posted: 10/23/03
Wires will be hidden behind the interior panels

357 finishing up 066.jpg
868 hits | 60.45 KB | Posted: 10/23/03
Took me an hour and a half to figure out that I can NOT get that screw in.

357 finishing up 067.jpg
882 hits | 71.63 KB | Posted: 10/23/03
So....I ripped the pod back off

357 finishing up 068.jpg
879 hits | 73.82 KB | Posted: 10/23/03
Countersunk the holes

357 finishing up 069.jpg
883 hits | 72.84 KB | Posted: 10/23/03
There..all mounted

357 finishing up 070.jpg
885 hits | 78.99 KB | Posted: 10/23/03
Without the flash

357 finishing up 074.jpg
939 hits | 74.57 KB | Posted: 10/23/03
Countersunk screws look good I think

357 finishing up 075.jpg
896 hits | 92.66 KB | Posted: 10/24/03
Pulled the grille again today so I can finish my wiring

357 finishing up 076.jpg
961 hits | 80.17 KB | Posted: 10/24/03
you can see the sending unit for my tranny temp guage

357 finishing up 078.jpg
911 hits | 63.91 KB | Posted: 10/24/03
Tomorows project...Maybe

357 finishing up 079.jpg
895 hits | 78.74 KB | Posted: 10/24/03
Hard to see them, but I installed hood lights

357 finishing up 084.jpg
950 hits | 80.03 KB | Posted: 10/24/03
This is where my MSD box used to be, So I filled the holes with wires

11-3-03 034.jpg
995 hits | 86.25 KB | Posted: 11/3/03
All done...even the linkage cap thingy

11-3-03 036.jpg
941 hits | 86.28 KB | Posted: 11/3/03
Other side