DSCF0434.JPG
4283 hits | 77.23 KB | Posted: 8/16/04

87 HP 60. dual rear wheels, kingpins, and 4.10s.
DSCF0435.JPG
3282 hits | 84.15 KB | Posted: 8/16/04

inside driver #1bracket.jpg
3060 hits | 42.31 KB | Posted: 8/20/04

rough plan for the front crossmember
DSCF0438.JPG
3224 hits | 63.72 KB | Posted: 8/21/04

mockup of the crossmember. spring perches will be welded to the bottom of it.
DSCF0441.JPG
3952 hits | 67.71 KB | Posted: 8/23/04

DRW hubs vs. SRW hubs. the dually hubs add about 5" of width per side compared to the single wheel o...
DSCF0442.JPG
3166 hits | 72.31 KB | Posted: 8/23/04

grinding and beating off the old trac bar mount.
DSCF0444.JPG
2946 hits | 72.68 KB | Posted: 8/23/04

all gone
DSCF0443.JPG
3242 hits | 71.16 KB | Posted: 8/23/04

notch cut into the webbing for u-bolt flip
DSCF0439.JPG
2982 hits | 68.37 KB | Posted: 8/23/04

60 shaft vs a TTB 44 shaft
DSCF0440.JPG
2953 hits | 73.91 KB | Posted: 8/23/04

notice how small the 44 shaft necks down too. i'm not sure if a solid 44 shaft does this as well, bu...
DSCF0447.JPG
3139 hits | 38.4 KB | Posted: 8/25/04

where the fins on the crossmember will go
DSCF0448.JPG
3032 hits | 38.92 KB | Posted: 8/25/04

same thing, other side
DSCF0449.JPG
3170 hits | 79.95 KB | Posted: 9/1/04

DSCF0463.JPG
3560 hits | 68.75 KB | Posted: 9/1/04

DSCF0464.JPG
5200 hits | 50.91 KB | Posted: 9/1/04

DSCF0474.JPG
3845 hits | 52.9 KB | Posted: 9/1/04

DSCF0496.JPG
5137 hits | 72.87 KB | Posted: 9/2/04

left side frame horn and crossmember
DSCF0497.JPG
5182 hits | 61.77 KB | Posted: 9/2/04

same thing
DSCF0498.JPG
3816 hits | 54.34 KB | Posted: 9/2/04

turn your head, front shock mount. left over from TTB lower and stock f250 upper
DSCF0499.JPG
5764 hits | 68.5 KB | Posted: 9/2/04

looks right at home
DSCF0500.JPG
5515 hits | 70.28 KB | Posted: 9/2/04

stock f350 rear hanger moved forward and a shot of the shackle angle
DSCF0501.JPG
3759 hits | 56.67 KB | Posted: 9/2/04

rear pinion angle is fubared after shackle flip, only because when the 14 bolt was installed, we too...
DSCF0502.JPG
5658 hits | 57.08 KB | Posted: 9/2/04

Sky Manufacturing shackle flip kit. the flip is good for about 4.5" of lift. its uber easy to instal...
DSCF0506.JPG
3515 hits | 53.95 KB | Posted: 9/2/04

duct tape drive flange
DSCF0505.JPG
5931 hits | 77.36 KB | Posted: 9/2/04

side shot showing the new stance
DSCF0504.JPG
5126 hits | 54.55 KB | Posted: 9/2/04

right side shackle shot
DSCF0510.JPG
3698 hits | 60.29 KB | Posted: 9/13/04

DSCF0509.JPG
3207 hits | 52.62 KB | Posted: 9/13/04

60bling 001.jpg
2362 hits | 54.38 KB | Posted: 5/11/08

truss and bling
60bling 010.jpg
2328 hits | 52.94 KB | Posted: 5/11/08

60bling 011.jpg
2178 hits | 43.79 KB | Posted: 5/11/08

60bling 002.jpg
2208 hits | 48.6 KB | Posted: 5/11/08

60bling 009.jpg
2231 hits | 49.2 KB | Posted: 5/11/08

4340 35 spline outers
60bling 013.jpg
2162 hits | 39.85 KB | Posted: 5/11/08


About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2024 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog