 DSC01933.jpg
649 hits | 50.9 KB | Posted: 7/19/09
http://e36v8.com/
[email protected]
(Posted in: V8 Ford)
 DSC01645.jpg
639 hits | 56.54 KB | Posted: 7/19/09
http://e36v8.com/
[email protected]
(Posted in: V8 Ford)
 11_09_06_1655.jpg
633 hits | 35.86 KB | Posted: 11/11/06
(Posted in: Z3)
 butterflyLoose.jpg
633 hits | 43.67 KB | Posted: 6/3/09
luckily i noticed that the screws holding the butterfly were loose before mounting the bypass
(Posted in: intake reseal)
 DSC02259.jpg
632 hits | 48.86 KB | Posted: 7/26/09
http://e36v8.com/
[email protected]
(Posted in: V8 Ford)
 DSC01791.jpg
630 hits | 50.01 KB | Posted: 7/19/09
http://e36v8.com/
[email protected]
(Posted in: V8 Ford)
 CuppedFlange.jpg
609 hits | 48.09 KB | Posted: 6/2/09
blower mounting flange is not flat, a little rub with a file shows the high and low areas
(Posted in: intake reseal)
 filling.jpg
607 hits | 60.66 KB | Posted: 6/2/09
back together and filling with synthetic supercharger oil, i used about 6oz
(Posted in: intake reseal)
 IntakeElbow.jpg
602 hits | 57.35 KB | Posted: 6/2/09
intake elbow installed with a little Permatex Red 'Hylomar' anerobic sealant on my homemade gasket
(Posted in: intake reseal)
 DSC01286.jpg
599 hits | 55.99 KB | Posted: 7/19/09
http://e36v8.com/
[email protected]
(Posted in: V8 Ford)
 LowSpot.jpg
597 hits | 51.43 KB | Posted: 6/2/09
some more rubbing with the file shows the lowest spot, could've been the problem?
(Posted in: intake reseal)
 IntakePort.jpg
592 hits | 41.61 KB | Posted: 6/2/09
the ends of the rotor lobes through the intake port
(Posted in: intake reseal)
 BlauWires.jpg
588 hits | 52.38 KB | Posted: 6/17/09
it might not look like much but it was a lot of work.
(Posted in: console restoration)
 IMGP0004.JPG
588 hits | 115.8 KB | Posted: 9/30/12
these are the hardparts of the discontinued T19-0085-08 passive radiator and the new foams, SWK4B & SWK525 from SpeakerWorks .com
(Posted in: KSC-WA62RC rebuild)
 pigg.JPG
581 hits | 103.22 KB | Posted: 10/23/11
looks like the pinion is seized minimum... cruisin along ~50 mph & the rear end locks up, back tires start bouncin down the road, fishtailin to the shoulder... & she comes to rest 1/2 on / off the road, all done
(Posted in: differential swap)
 3rdBulbLit.jpg
580 hits | 42.75 KB | Posted: 6/14/09
i joined the 2 original power wire pairs together and tapped all 3 bulbs off the 2, so the added draw and dimmer control would be more even, we'll see...
(Posted in: console restoration)
 Z3cover.JPG
577 hits | 139.45 KB | Posted: 5/21/11
inside the cover has oil spray tubes for the cam lobes, the transfer seal is dealer only
(Posted in: 1.9 16v)
 DSC01931.jpg
576 hits | 63.79 KB | Posted: 7/19/09
http://e36v8.com/
[email protected]
(Posted in: V8 Ford)
 DSC01497.jpg
565 hits | 74.76 KB | Posted: 7/19/09
http://e36v8.com/
[email protected]
(Posted in: V8 Ford)
 DSC01675.jpg
565 hits | 54.63 KB | Posted: 7/19/09
http://e36v8.com/
[email protected]
(Posted in: V8 Ford)
 busted.jpg
558 hits | 46.29 KB | Posted: 6/14/09
thanks to the cretin that broke a window and trashed my console for a cheap radio
(Posted in: console restoration)
 lowergrill.jpg
553 hits | 43.46 KB | Posted: 6/29/09
a little kraut
(Posted in: Z3)
 DSC01126.jpg
542 hits | 82.26 KB | Posted: 7/19/09
http://e36v8.com/
[email protected]
(Posted in: V8 Ford)
 3rdBulbIn.jpg
539 hits | 43.59 KB | Posted: 6/14/09
i added an extra bulb to the climate control housing, the left side is dark with no bulb
(Posted in: console restoration)
 windownew.jpg
518 hits | 50.15 KB | Posted: 7/11/09
try doin that by yourself! i figured it'd be easier than with the available 'help'. actually it went really well, nailed it on the first try
(Posted in: Z3)
 windowold.jpg
515 hits | 37.66 KB | Posted: 7/11/09
don't let this happen to you. i didn't mind the 'tint' until it started cracking
(Posted in: Z3)
 BlauBahamas.jpg
513 hits | 55.35 KB | Posted: 6/17/09
cheaper radio, NIB $55! install T&M was more than the unit by far.
(Posted in: console restoration)
 IMGP0013.JPG
510 hits | 121.44 KB | Posted: 9/30/12
ready to re-install into the car & rock on. plan is to watch the settings for the levels and minimize UV exposure so the new foams last a while
(Posted in: KSC-WA62RC rebuild)
 DSC00941.jpg
497 hits | 75.33 KB | Posted: 7/19/09
http://e36v8.com/
[email protected]
(Posted in: V8 Ford)
 7_06_09.jpg
491 hits | 60.43 KB | Posted: 7/6/09
(Posted in: Z3)
 IMGP0007.JPG
460 hits | 115.14 KB | Posted: 9/30/12
now the center cone front side foam attached to the basket front side foam. the ring in the pic above fits at the joint of the 2 foams
(Posted in: KSC-WA62RC rebuild)
 IMGP0006.JPG
443 hits | 118.6 KB | Posted: 9/30/12
the center cone with a foam attached to the bottom side, & the basket with a foam attached to the front side
(Posted in: KSC-WA62RC rebuild)
 IMGP0011.JPG
405 hits | 111.14 KB | Posted: 9/30/12
housing halves closed up & ready to replace back panel
(Posted in: KSC-WA62RC rebuild)
 IMGP0005.JPG
401 hits | 117.27 KB | Posted: 9/30/12
i was afraid that the adhesive that comes with the foams might not stick to the plastic parts, and the foams got a little weird from the Loctite product so i 'pre-buttered' the plastic surfaces so the foams wouldn't be ruined and the supplied adhesiv...
(Posted in: KSC-WA62RC rebuild)
 mirror1.JPG
385 hits | 103.93 KB | Posted: 11/11/12
a closer shot of the different mount styles. with a small soaked towel as a heat sink on the outside of the glass, i used a triple jet lighter to gently warm up the mount pellet on the inside. it let go after the glue started to smoke a bit
(Posted in: rear view mirror )
 mirror5.JPG
385 hits | 126.66 KB | Posted: 11/11/12
nothing strange looking from the outside
(Posted in: rear view mirror )
 IMGP0009.JPG
382 hits | 122.04 KB | Posted: 9/30/12
back side foams both installed with the ring sandwiched in the middle. torn silver stuff is decorative, used to be on the front but i decided it wasn't worth the risk to try to clean it off any further... i just turned it to the back side
(Posted in: KSC-WA62RC rebuild)
 mirror7.JPG
375 hits | 113.09 KB | Posted: 11/11/12
(Posted in: rear view mirror )
 mirror6.JPG
373 hits | 113.55 KB | Posted: 11/11/12
(Posted in: rear view mirror )
 IMGP0012.JPG
369 hits | 103.03 KB | Posted: 9/30/12
back panel with my mounting bracket all buttoned up
(Posted in: KSC-WA62RC rebuild)
 mirror4.JPG
367 hits | 102.96 KB | Posted: 11/11/12
the Ford mirror has more adjustability and is able to be raised up higher than the original, eliminating the notorious Z3 blind spot behind the rear view
(Posted in: rear view mirror )
 mirror3.JPG
352 hits | 107.72 KB | Posted: 11/11/12
top: the original Z3 mirror started dropping pieces of the ball socket lock ring onto the console and the effort to adjust the mirror became much easier, i knew it wouldn't be long until it let go completely
dealer price $273.xx including tax !
...
(Posted in: rear view mirror )
 mirror2.JPG
350 hits | 111.49 KB | Posted: 11/11/12
barely any difference at all in overall shape & size
(Posted in: rear view mirror )
 mirror8.JPG
343 hits | 117.79 KB | Posted: 11/11/12
(Posted in: rear view mirror )
 HaloParks.JPG
282 hits | 93.13 KB | Posted: 3/21/15
(Posted in: Projector headlamps)
|
