DSC01779.JPG
509 hits | 49.67 KB | Posted: 11/23/03
The oil pump, filter, and magnetic particle pick-up washer
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01781.JPG
514 hits | 64.19 KB | Posted: 11/23/03
The front output shaft
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01782.JPG
531 hits | 65.83 KB | Posted: 11/23/03
The rear output shaft
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01783.JPG
517 hits | 63.5 KB | Posted: 11/23/03
The "gooey" magnetic particle pick-up washer that is full of metal
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01786.JPG
515 hits | 60.71 KB | Posted: 11/23/03
Look at how dirty it is
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01789.JPG
546 hits | 55.25 KB | Posted: 11/23/03
A better look at where the filter and magnet were
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01794.JPG
542 hits | 52.48 KB | Posted: 11/23/03
NASTY!......those are two pieces of plastic that I was never able to figure out where they came from
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01797.JPG
498 hits | 65.68 KB | Posted: 11/23/03
A better look at the "goo" on both the filter and the magnet....the red is from the teeth on my speedo gear
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01799.JPG
544 hits | 70.75 KB | Posted: 11/23/03
Got the chain off with a little "gentle persuation"
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01800.JPG
599 hits | 71.96 KB | Posted: 11/23/03
That is a beefy chain
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01805.JPG
604 hits | 72.95 KB | Posted: 11/23/03
Off it comes
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01806.JPG
535 hits | 71.75 KB | Posted: 11/23/03
The inside without the chain
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01809.JPG
555 hits | 74.89 KB | Posted: 11/23/03
Out it comes, and a big "thank you" to Gee (pictured) who is helping
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01810.JPG
500 hits | 67.28 KB | Posted: 11/23/03
It is big and heavy
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01812.JPG
536 hits | 66.61 KB | Posted: 11/23/03
The case without the rear output shaft
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01814.JPG
575 hits | 68.21 KB | Posted: 11/23/03
Another angle
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01820.JPG
537 hits | 44.65 KB | Posted: 11/23/03
The two shafts side by side to demonstrate the difference in length
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01821.JPG
517 hits | 49.72 KB | Posted: 11/23/03
All these gears need to be transfered to the new shaft
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01828.JPG
468 hits | 41.59 KB | Posted: 11/23/03
These two needle bearings need to come out so that the gears will slip onto the new shaft
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01829.JPG
513 hits | 43.01 KB | Posted: 11/23/03
After they come out they will be discarded
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01842.JPG
533 hits | 37.13 KB | Posted: 11/23/03
This PVC pipe is the perfect diameter to do the job
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01844.JPG
514 hits | 47.68 KB | Posted: 11/23/03
There we go, let me get the hammer
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01845.JPG
477 hits | 38.54 KB | Posted: 11/23/03
See......perfect
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01847.JPG
503 hits | 55.21 KB | Posted: 11/23/03
Just like this......I found a deadblow hammer to work better than this rubber mallet
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01848.JPG
520 hits | 71.1 KB | Posted: 11/23/03
Now they are out
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01853.JPG
568 hits | 52.35 KB | Posted: 11/23/03
Now the gears are on the new shaft
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01854.JPG
551 hits | 51.05 KB | Posted: 11/23/03
A new comparison
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01867.JPG
551 hits | 76.97 KB | Posted: 11/23/03
Look how dirty
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01869.JPG
496 hits | 78.94 KB | Posted: 11/23/03
Maybe I should clean this up
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01870.JPG
533 hits | 48.76 KB | Posted: 11/23/03
This looks better when it is clean
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01878.JPG
538 hits | 46.54 KB | Posted: 11/23/03
This lock ring was very hard to put on
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01882.JPG
551 hits | 65.75 KB | Posted: 11/23/03
Front half all cleaned up
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01886.JPG
556 hits | 51.92 KB | Posted: 11/23/03
Cleaned this part also
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01889.JPG
543 hits | 38.93 KB | Posted: 11/23/03
Putting a seal on the housing
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01890.JPG
535 hits | 53.43 KB | Posted: 11/23/03
Rear half on with the speedo gear track installed with 2 more lock rings
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01891.JPG
551 hits | 49.85 KB | Posted: 11/23/03
Closer look
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01894.JPG
562 hits | 42.87 KB | Posted: 11/23/03
The type of RTV we used
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01896.JPG
546 hits | 38.04 KB | Posted: 11/23/03
Applying the RTV to the rear housing
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01897.JPG
599 hits | 59.17 KB | Posted: 11/23/03
On it goes
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01899.JPG
543 hits | 60.36 KB | Posted: 11/23/03
Another view
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01901.JPG
548 hits | 62.37 KB | Posted: 11/23/03
A look from the driver side
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01902.JPG
488 hits | 72.75 KB | Posted: 11/23/03
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01903.JPG
545 hits | 70.21 KB | Posted: 11/23/03
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01907.JPG
541 hits | 54.62 KB | Posted: 11/23/03
A look inside the speedo housing
(Posted in: SYE/Driveshaft Install 11/22/03)

DSC01911.JPG
556 hits | 73.53 KB | Posted: 11/23/03
I cleaned up the transfer case skid plate
(Posted in: SYE/Driveshaft Install 11/22/03)