2 inch BB lift 009.jpg 657 hits | 57.73 KB | Posted: 4/10/04 Took the bottom control arm loose (Posted in: 2" spacer Lift)
2 inch BB lift 010.jpg 2102 hits | 38.93 KB | Posted: 4/10/04 Spacer goes on afer the spring is removed..these are from "Kevins JeepParts.com" (Posted in: 2" spacer Lift)
2 inch BB lift 011.jpg 2861 hits | 63.3 KB | Posted: 4/10/04 Spring set into position (Posted in: 2" spacer Lift)
2 inch BB lift 012.jpg 2996 hits | 58.91 KB | Posted: 4/10/04 Control arm back together (Posted in: 2" spacer Lift)
2 inch BB lift 014.jpg 952 hits | 50.1 KB | Posted: 4/10/04 Drivers side (Posted in: 2" spacer Lift)
2 inch BB lift 017.jpg 888 hits | 67.54 KB | Posted: 4/10/04 All torn apart (Posted in: 2" spacer Lift)
2 inch BB lift 025.jpg 659 hits | 60.86 KB | Posted: 4/10/04 Last shot before we do the rear (Posted in: 2" spacer Lift)
2 inch BB lift 027.jpg 641 hits | 53.57 KB | Posted: 4/10/04 Back before it comes apart (Posted in: 2" spacer Lift)
2 inch BB lift 029.jpg 687 hits | 49.04 KB | Posted: 4/10/04 This sleeve keeps things together while the axle flexes offroad...we drilled holes, (Posted in: 2" spacer Lift)
2 inch BB lift 030.jpg 741 hits | 52.89 KB | Posted: 4/10/04 And rivited it on (Posted in: 2" spacer Lift)
2 inch BB lift 031.jpg 649 hits | 54.48 KB | Posted: 4/10/04 I drilled and tapped the spacers to keep them in place while flexing (Posted in: 2" spacer Lift)
2 inch BB lift 034.jpg 641 hits | 47.53 KB | Posted: 4/10/04 Turned out neat!! Todds Idea BTW... (Posted in: 2" spacer Lift)
2 inch BB lift 035.jpg 635 hits | 53.46 KB | Posted: 4/11/04 Spring in position (Posted in: 2" spacer Lift)
2 inch BB lift 037.jpg 739 hits | 49.2 KB | Posted: 4/11/04 Drivers side torn down (Posted in: 2" spacer Lift)
2 inch BB lift 039.jpg 730 hits | 61.84 KB | Posted: 4/11/04 Going back together (Posted in: 2" spacer Lift)
2 inch BB lift 045.jpg 749 hits | 67.38 KB | Posted: 4/11/04 Looks good (Posted in: 2" spacer Lift)
2 inch BB lift 043.jpg 746 hits | 70.69 KB | Posted: 4/11/04 Lift all done so the tires fit well, now back to the engine (Posted in: 2" spacer Lift)
Engine reassembly 001.jpg 543 hits | 70.62 KB | Posted: 4/10/04 Engine back from the machine shop (Posted in: Engine reassembly)
Engine reassembly 021.jpg 441 hits | 66.8 KB | Posted: 4/14/04 Set the bearings in dry to check clearances with plastigage (Posted in: Engine reassembly)
Engine reassembly 022.jpg 471 hits | 72.32 KB | Posted: 4/14/04 Then the polished crank on top...It did not need to be ground, just polished (Posted in: Engine reassembly)
Engine reassembly 025.jpg 432 hits | 69.74 KB | Posted: 4/14/04 Torqued them down to 80, then checked the plastigage, all checked out OK (Posted in: Engine reassembly)
Engine reassembly 026.jpg 536 hits | 65.65 KB | Posted: 4/14/04 New rear main seal installed (Posted in: Engine reassembly)
Engine reassembly 027.jpg 487 hits | 59.16 KB | Posted: 4/14/04 All mains are done, rods/pistons next (Posted in: Engine reassembly)
Engine reassembly 034.jpg 496 hits | 53.18 KB | Posted: 4/14/04 Using the piston to put the ring into the bore straight to measure end gap (Posted in: Engine reassembly)
