TracLok03.JPG
856 hits | 39.74 KB | Posted: 3/13/04
Used TracLok parts. Notice clutches and S-Spring are worn out.
(Posted in: General)

CclipsModified.JPG
782 hits | 15.67 KB | Posted: 3/13/04
Modified the C-Clips to allow installation/removal with the extra 2 clutches installed.
(Posted in: General)

65to70.JPG
799 hits | 82.28 KB | Posted: 3/13/04
FRPP 70mm TB compared with stock 65mm unit. Outside diameters are the same.
(Posted in: General)

70on65.JPG
805 hits | 56.08 KB | Posted: 3/13/04
FRPP 70mm TB compared to stock 65mm unit.
(Posted in: General)

KBDeadPedal02.JPG
1175 hits | 69.56 KB | Posted: 3/13/04
Kenny Brown Dead Pedal Installed.
(Posted in: General)

KeylessEntryPad01.JPG
709 hits | 38.59 KB | Posted: 3/13/04
My Keyless Entry Number Pad Quit Working. Water had leaked into and corroded it. Had to replace with new unit.
(Posted in: General)

KeylessEntryPad02-.JPG
758 hits | 29.22 KB | Posted: 3/13/04
Keyless Entry Number Pad Internals.
(Posted in: General)

FanModuleFail.jpg
669 hits | 40.78 KB | Posted: 3/13/04
The solider joint went bad in my A/C blower circuit. This is mounted inside the airbox. As result my fan would quit blowing all together at times. I resolidered the junction and no more troubles.
(Posted in: General)

UDComp01.JPG
759 hits | 34.01 KB | Posted: 3/13/04
Steeda underdrive pulleys compared to stock. (Back when I was n/a)
(Posted in: General)

UDRemovalTools.JPG
800 hits | 39.72 KB | Posted: 3/13/04
Proper removal tools. It took an 1/2" impact 6-point 18mm socket to get the harmonic balancer bolt off with the steeda in place. broke a few tools trying first...
(Posted in: General)

Heads-.JPG
615 hits | 47.03 KB | Posted: 3/13/04
Rennegade Ported NonPI Heads
Oversized CC Valves
Few Miles of Breakin
(Posted in: Heads)

IntakePort1.JPG
614 hits | 48.09 KB | Posted: 3/13/04
Rennegade Ported NonPI Heads
*Intake Port CNC'd
*SS Valves
*Bronze Valve Guides
(Posted in: Heads)

ExhaustPort-.JPG
607 hits | 27.1 KB | Posted: 3/13/04
Rennegade Ported NonPI Head Exhaust Port

(Posted in: Heads)

ValveSprings-.JPG
672 hits | 58.04 KB | Posted: 3/13/04
Rennegade Ported NonPI Head Valve Springs

(Posted in: Heads)

2000GMbaseline-.jpg
674 hits | 49.04 KB | Posted: 3/13/04
This is what my car did mostly stock.
Nice torque.
(Posted in: Dyno)

AED Almost Tuned.jpg
685 hits | 57.35 KB | Posted: 3/13/04
This is a nice looking dyno graph, before pushing the timing.
*Stock NonPI longblock
*PI cams
*AED 6psi Supercharger
*FRPP shorty headers/Reinhart Exhaust
*Marauder Airbox
*ADTR Intake Tube
*FRPP 70mm TB
(Posted in: Dyno)

AED Tuned & Start.jpg
605 hits | 58.54 KB | Posted: 3/13/04
This is the supplied and tweeked tuning dyno graphs. (TC unlocked in during the pull.)
*Stock NonPI longblock
*PI cams
*AED 6psi Supercharger
*FRPP shorty headers/Reinhart Exhaust
*Marauder Airbox
*ADTR Intake Tube
*FRPP 70mm TB
(Posted in: Dyno)

JohnEComp.jpg
701 hits | 33.48 KB | Posted: 3/13/04
NA Baseline compared to AED 6psi with PI cams
(Posted in: Dyno)

JohnESW.JPG
678 hits | 75.25 KB | Posted: 3/13/04
Car on Speedworks Dyno
(Posted in: Dyno)

GrillCooler03.JPG
555 hits | 22.03 KB | Posted: 3/13/04
This is a BEHR cooler which I made custom fittings to use 3/4" hose and mount in the grill area.
(Posted in: Cooling)

UnderCoolers02-.JPG
615 hits | 71.58 KB | Posted: 3/13/04
Here is the supplied AED Peracool Cooler on passenger side (1/3) & BEHR cooler (2/3) mounted underside.
(Posted in: Cooling)

GrillCooler06-.JPG
613 hits | 33.28 KB | Posted: 3/13/04
BEHR Cooler mounted in grill (3/3)
(Posted in: Cooling)

JohnEEngine05.JPG
616 hits | 65.33 KB | Posted: 3/13/04
Bosch electric coolant pump is mounted behind the degassing tank, sitting on fender well. COOLANT ROUTING: 1)Coolant leaves bottom of the degassing tank. 2)Goes into the pump. 3) Enters lower square BEHR cooler. 4) Enters lower Peracool. 5) Enters u...
(Posted in: Cooling)

BentHose-.JPG
627 hits | 60.12 KB | Posted: 3/13/04
Kinking trouble with standard hose between pump and tank.
(Posted in: Cooling)

M4371 HeaterHose-.JPG
643 hits | 26.82 KB | Posted: 3/13/04
Pre-formed Heater Hose I found to rid kinking trouble. (found at AutoZn, M4371) Only need to cut a small portion off to work out.
(Posted in: Cooling)

M4371 HoseOnPump-.JPG
622 hits | 51.63 KB | Posted: 3/13/04
Pre-formed hose installed.
(Posted in: Cooling)

GM Stock Engine.jpg
727 hits | 77.2 KB | Posted: 3/13/04
Bone Stock 2000 Engine
(Posted in: Engine)

NoIntake.JPG
751 hits | 84.26 KB | Posted: 3/13/04
Intake removed, stock shortblock.
(Posted in: Engine)

JohnEEngine05.JPG
762 hits | 94.31 KB | Posted: 3/13/04
AED on top, Marauder Airbox, ADTR Intake, Bosch Inercooler Pump.
(Posted in: Engine)

JohnE005.JPG
720 hits | 77 KB | Posted: 3/13/04
AED on top, Marauder Airbox, ADTR Intake, Bosch Inercooler Pump.
(Posted in: Engine)

OilLeakMess.JPG
648 hits | 69.11 KB | Posted: 3/13/04
Here's the mess the oil leak made topside. Under the car oil was blown everywhere!
(Posted in: FrontCover)

CrackCover03-.JPG
650 hits | 48.84 KB | Posted: 3/13/04
The front engine cover developed a crack, just under the tensioner mount.
(Posted in: FrontCover)

LeakI04-.JPG
531 hits | 56.06 KB | Posted: 3/13/04
Close shot of the oil mess.
(Posted in: FrontCover)

72merc.jpg
849 hits | 40.34 KB | Posted: 5/19/04
Derby car 1
(Posted in: Merc)

72Merc2.jpg
732 hits | 44.32 KB | Posted: 5/20/04
(Posted in: Merc)

Fresh.jpg
821 hits | 62.8 KB | Posted: 8/13/04
(Posted in: Merc)

Wrecked.JPG
923 hits | 38.75 KB | Posted: 8/13/04
(Posted in: Merc)