IMG_20170811_112949903.jpg
76 hits | 67.47 KB | Posted: 8/11/17
The hitch receiver seems to fit well, but it only has a round 4-pin connector with a very old electronic taillight adapter hanging from the underbody wiring.

The rear wiper blade is missing.
(Posted in: Base album)

IMG_20170811_113040090.jpg
81 hits | 65.77 KB | Posted: 8/11/17
The front bumper is bent, and all 4 end caps are damaged.
(Posted in: Base album)

IMG_20170811_112918940.jpg
83 hits | 45.13 KB | Posted: 8/11/17
Although it seems to work, and doesn't appear to leak, it doesn't look right overhanging the roof ribs.
(Posted in: Base album)

IMG_20170811_112851395.jpg
93 hits | 65.93 KB | Posted: 8/11/17
(Posted in: Base album)

20170817_185515.jpg
96 hits | 92.88 KB | Posted: 8/17/17
All the mating surfaces are bright now (including the one I had to use the wire toothbrush on), and I'll be sure to tighten all the fasteners.
(Posted in: Base album)

IMG_20170811_112548071_HDR.jpg
97 hits | 78.78 KB | Posted: 8/11/17
(Posted in: Base album)

IMG_20170811_112816676.jpg
97 hits | 66.66 KB | Posted: 8/11/17
The trans shifter is loose above & below the floor; the key comes out in several positions; the aftermarket PW system is unreliable; the aftermarket PL/RKE system has been abandoned; the aftermarket sunroof seems to work perfectly.
(Posted in: Base album)

IMG_20170811_114413194.jpg
97 hits | 72.99 KB | Posted: 8/11/17
(Posted in: Base album)

IMG_20170811_113247394.jpg
100 hits | 82.78 KB | Posted: 8/11/17
The aftermarket cruise servo's cable was coiled up right in front of it. Its VSS wiring is ripped away underneath, and there's no sign of any VSS.
(Posted in: Base album)

IMG_20170811_114423727.jpg
101 hits | 81.23 KB | Posted: 8/11/17
(Posted in: Base album)

20170814_021234268_HDR.jpg
101 hits | 73.46 KB | Posted: 8/17/17
Just to get a general idea, I pulled the easiest plug (#4) to inspect. It has the correct amount of tan ash on the insulator, indicating that the engine (or at least cylinder #4) is generally running well. I'll blast the plug clean before reinstall...
(Posted in: Base album)

image.jpeg
107 hits | 35.1 KB | Posted: 8/8/16
(Posted in: Bronco parts)

20170817_175305.jpg
107 hits | 88.46 KB | Posted: 8/17/17
This was the big problem: the alternator pivot bolt was barely hand-tight. So it wasn't clamped onto the engine bracket, and wasn't making a good ground contact between the case & block. The lower (front) alternator tab in the right foreground show...
(Posted in: Base album)

IMG_20170811_112511653_HDR.jpg
108 hits | 64.97 KB | Posted: 8/11/17
(Posted in: Base album)

image.jpeg
110 hits | 26.03 KB | Posted: 8/8/16
(Posted in: Bronco parts)

IMG_20170811_113101080.jpg
114 hits | 48.81 KB | Posted: 8/11/17
The aftermarket running boards were installed wrong (to frame AND body), and this side isn't even attached to its brace (which is barely attached to the frame).
(Posted in: Base album)

20170817_175242.jpg
115 hits | 83.28 KB | Posted: 8/17/17
After a few voltage checks under load, I realized that there was high resistance at both the alternator output (positive) and case ground (negative). So I pulled the smog pump & alternator to fix it.

The burned spots on the ring terminal & the alte...
(Posted in: Base album)

20170817_193122.jpg
115 hits | 68.13 KB | Posted: 8/17/17
Since I was cleaning up the others, I pulled the compressor & cleaned the main battery ground terminal to the engine mount. Turns out it was already clean & tight, but now it's cleaner & tighter.
(Posted in: Base album)

IMG_20170811_113340040.jpg
117 hits | 65 KB | Posted: 8/11/17
The aftermarket power window system barely works; partially due to the glass runs being old.
(Posted in: Base album)

image.jpeg
125 hits | 13.93 KB | Posted: 8/8/16
(Posted in: Bronco parts)

IMG_20170811_113205020.jpg
126 hits | 79.15 KB | Posted: 8/11/17
I guess the switch was added for storage, but it's a poor way to accomplish what a trickle charger would do MUCH better. Both battery terminals (and the battery) are cheap junk. The one fusible link is installed poorly.

The side marker lights had ...
(Posted in: Base album)

20170828_002902.jpg
131 hits | 85.79 KB | Posted: 8/28/17
Air cleaner label
(Posted in: Base album)

IMG_20170811_113503113.jpg
132 hits | 97.89 KB | Posted: 8/11/17
The rodent who nested in the kick doesn't appear to be responsible for the wiring problems.
(Posted in: Base album)

20170828_002930.jpg
141 hits | 75.71 KB | Posted: 8/28/17
Smog pump label
(Posted in: Base album)

20170828_003021.jpg
142 hits | 66.25 KB | Posted: 8/28/17
Belt 1
(Posted in: Base album)

image.jpeg
146 hits | 25.44 KB | Posted: 8/8/16
(Posted in: Bronco parts)

IMG_20170811_113354571.jpg
147 hits | 90.04 KB | Posted: 8/11/17
There are at least 5 aftermarket systems hacked into the dash wiring below the column, but some of them are abandoned.
(Posted in: Base album)

image.jpeg
148 hits | 31.86 KB | Posted: 8/8/16
(Posted in: Bronco parts)

image.jpeg
149 hits | 22.52 KB | Posted: 8/8/16
(Posted in: Bronco parts)

IMG_20170811_112604844.jpg
150 hits | 99.96 KB | Posted: 8/11/17
Problems include:
- battery terminals & fusible links
- antenna mast & unmounted CB antenna base
- valve cover & filter adapter leaks
- A/C leak
- cruise control inop
- extra wiring butchered in & abandoned
- rodent damage
- speedo cable damaged & le...
(Posted in: Base album)

image.jpeg
152 hits | 35.92 KB | Posted: 8/8/16
(Posted in: Bronco parts)

20170828_001741.jpg
153 hits | 81.75 KB | Posted: 8/28/17
Unidentified hitch receiver
(Posted in: Base album)

image.jpeg
154 hits | 37.59 KB | Posted: 8/8/16
(Posted in: Bronco parts)

image.jpeg
154 hits | 38.43 KB | Posted: 8/8/16
(Posted in: Bronco parts)

20170828_003213.jpg
154 hits | 86.66 KB | Posted: 8/28/17
Fuel filter
(Posted in: Base album)

image.jpeg
155 hits | 86.66 KB | Posted: 8/8/16
(Posted in: Bronco parts)

image.jpeg
156 hits | 23.26 KB | Posted: 8/8/16
(Posted in: Bronco parts)

20170828_003155.jpg
156 hits | 83.34 KB | Posted: 8/28/17
Coil & igniter labels
(Posted in: Base album)

20170828_001819.jpg
162 hits | 61.69 KB | Posted: 8/28/17
Unidentified hitch receiver w/round 4-pin connector
(Posted in: Base album)

image.jpeg
165 hits | 62.08 KB | Posted: 8/8/16
(Posted in: Bronco parts)

20170828_002958.jpg
166 hits | 77.58 KB | Posted: 8/28/17
Belt 3
(Posted in: Base album)

IMG_20170811_114330797.jpg
167 hits | 60.34 KB | Posted: 8/11/17
(Posted in: Base album)

20170828_001700.jpg
191 hits | 80.75 KB | Posted: 8/28/17
Unidentified hitch receiver
(Posted in: Base album)

image.jpeg
195 hits | 38.36 KB | Posted: 8/8/16
(Posted in: Bronco parts)

image.jpeg
196 hits | 52.42 KB | Posted: 8/8/16
(Posted in: Bronco parts)