DSC03559.JPG
715 hits | 61.56 KB | Posted: 1/4/09
I added four LEDs in the square holes at the top of the climate control and wired them individually to the existing lights. To anchor them, use a hot soldering iron to melt the LED wire into the plastic.

I originally tried to do all four LEDs in ...
(Posted in: LED conversion)

DSC03263.JPG
750 hits | 15.27 KB | Posted: 12/22/08
The climate control turned out a lot better than it looks in this picture; there are no hot spots and the light distribution is even. The whole unit is readable while driving, but I think I'm going to move to some bigger bulbs. These are 3 mm and I...
(Posted in: LED conversion)

DSC03234.JPG
751 hits | 41.36 KB | Posted: 12/22/08
Insert the new LED to right at this height, then wrap one of the legs around the base like the old bulb and trim it to length. Wrap a resistor leg around the other side of the base, then solder the resistor to the other LED leg. You can get it nice...
(Posted in: LED conversion)

DSC03247.JPG
762 hits | 47.25 KB | Posted: 12/22/08
The two bulbs you'll find in the switches
(Posted in: LED conversion)

DSC03237.JPG
766 hits | 37.55 KB | Posted: 12/22/08
(Posted in: LED conversion)

DSC03264.JPG
784 hits | 11.08 KB | Posted: 12/22/08
Here are two finished dash switches next to an original so you can see the difference
(Posted in: LED conversion)

DSC03242.JPG
803 hits | 42.69 KB | Posted: 12/22/08
One with the resistor sticking up. This is easier to do than make it lie flat.
(Posted in: LED conversion)

DSC03258.JPG
816 hits | 53.74 KB | Posted: 12/22/08
I got better at making them look nice and sit flat
(Posted in: LED conversion)

DSC02098.JPG
828 hits | 63.28 KB | Posted: 7/16/08
Another view of the master switch
(Posted in: LED conversion)

DSC02097.JPG
839 hits | 58.74 KB | Posted: 7/16/08
(Posted in: LED conversion)

DSC02102.JPG
851 hits | 14.36 KB | Posted: 7/16/08
All installed. The camera lies; it's more red than this but still has a slight orange tint.
(Posted in: LED conversion)

DSC01848.JPG
861 hits | 64.08 KB | Posted: 2/28/08
(Posted in: Body shots)

DSC03260.JPG
865 hits | 88.8 KB | Posted: 12/22/08
The one at the right is scuffed with 200 grit sandpaper; the one on the left is not. You'll want to do that to diffuse the light.
(Posted in: LED conversion)

DSC03255.JPG
873 hits | 40.24 KB | Posted: 12/22/08
Disassemble these bulbs just like the switches
(Posted in: LED conversion)

DSC01845.JPG
882 hits | 56.55 KB | Posted: 2/28/08
(Posted in: Body shots)

DSC01844.JPG
883 hits | 45.78 KB | Posted: 2/28/08
(Posted in: Body shots)

DSC03562.JPG
890 hits | 88.86 KB | Posted: 1/4/09
I added four LEDs in the square holes at the top of the climate control and wired them individually to the existing lights. To anchor them, use a hot soldering iron to melt the LED wire into the plastic.

I originally tried to do all four LEDs in ...
(Posted in: LED conversion)

DSC02091.JPG
892 hits | 69.91 KB | Posted: 7/16/08
(Posted in: LED conversion)

DSC02095.JPG
905 hits | 64.23 KB | Posted: 7/16/08
Here's how to do the window switch on all but the master. Positive on the left, negative on the right. Cut the old LED wires just under the LED on the tower, then bend the left tab forward to solder the resistor to.
(Posted in: LED conversion)

DSC01856.JPG
940 hits | 55.97 KB | Posted: 2/28/08
(Posted in: Body shots)

DSC03565.JPG
963 hits | 14.85 KB | Posted: 1/4/09
Now it's a bit too bright on the top. I need to move the LEDs on the right side back a bit to even it out and it'll look perfect.
(Posted in: LED conversion)

DSC01846.JPG
988 hits | 62.57 KB | Posted: 2/28/08
(Posted in: Body shots)

DSC03230.JPG
995 hits | 40.89 KB | Posted: 12/22/08
Unwind the wires and pull the bulb straight out of the holder
(Posted in: LED conversion)

DSC03569.JPG
1005 hits | 74.71 KB | Posted: 1/7/09
The belt sliced neatly through the cover
(Posted in: Timing belts suck)

DSC02090.JPG
1008 hits | 40.44 KB | Posted: 7/16/08
Here's how to do the door lock switches. Positive on the left, negative on the right.
(Posted in: LED conversion)

DSC01847.JPG
1011 hits | 47.2 KB | Posted: 2/28/08
(Posted in: Body shots)

DSC02096.JPG
1024 hits | 59.51 KB | Posted: 7/16/08
The master switch. The polarity on the window switch LEDs is the reverse of all the other switches. Cut both LED s off near the top of the tower, then bend down the tab closest to the recess so you can solder the resistor down there.
(Posted in: LED conversion)

DSC01857.JPG
1028 hits | 59.2 KB | Posted: 2/28/08
(Posted in: Body shots)

DSC01842.JPG
1035 hits | 69.36 KB | Posted: 2/28/08
With the original wheels
(Posted in: Body shots)

DSC01855.JPG
1159 hits | 61.57 KB | Posted: 2/28/08
(Posted in: Body shots)

DSC01851.JPG
1207 hits | 68.91 KB | Posted: 2/28/08
With the wipers and cowl removed. The cabin air filter goes in that black box on the passenger side.
(Posted in: Tech pictures)

194_smt_a_wm.jpg
1297 hits | 10.51 KB | Posted: 4/3/09
(Posted in: LED conversion)

WLED-x5_mm.jpg
1304 hits | 33.13 KB | Posted: 4/3/09
(Posted in: LED conversion)

DSC03644.JPG
1304 hits | 52.04 KB | Posted: 1/18/09
Bad tensioner on the left, good one on the right
(Posted in: Timing belts suck)

DSC03250.JPG
1342 hits | 81.94 KB | Posted: 12/22/08
The back of the climate control unit panel. To get here, remove the radio, then reach behind the ECC and push it out towards you; it pops right out. Remove the four screws that hold the face on, then there are three tabs to release.
(Posted in: LED conversion)

DSC03589.JPG
1377 hits | 42.2 KB | Posted: 1/8/09
(Posted in: Timing belts suck)

DSC03587.JPG
1404 hits | 87.96 KB | Posted: 1/8/09
(Posted in: Timing belts suck)

DSC01858.JPG
1408 hits | 71.62 KB | Posted: 2/28/08
(Posted in: Body shots)

DSC03649.JPG
1439 hits | 73.41 KB | Posted: 1/23/09
The bottom of the upper head on an NA
(Posted in: Tech pictures)

DSC03586.JPG
1469 hits | 83.99 KB | Posted: 1/8/09
(Posted in: Timing belts suck)

DSC03588.JPG
1490 hits | 83.59 KB | Posted: 1/8/09
(Posted in: Timing belts suck)

DSC03646.JPG
1800 hits | 64.48 KB | Posted: 1/18/09
What you get in the box from Clearwater Cylinder Head, complete with cams.
(Posted in: Timing belts suck)

DSC03571.JPG
2329 hits | 63.2 KB | Posted: 1/7/09
The timing belt tensioner failed, feeding the intact belt out the cover
(Posted in: Timing belts suck)

DSC01854.JPG
2941 hits | 66.87 KB | Posted: 2/28/08
After installing the Cetus rims
(Posted in: Body shots)