|
|
Hits: 1415
Size: 80.34 KB
Posted: 8/23/03
in the beginning | 
Hits: 1251
Size: 84.26 KB
Posted: 8/23/03
passanger side spring and sway bar mounts | 
Hits: 1234
Size: 78.33 KB
Posted: 8/23/03
passanger side gone, still some grinding to do to make room for the radius arm mounts | 
Hits: 1308
Size: 78.64 KB
Posted: 8/23/03
drivers side brackets.
Also a decent shot of the top of a kingpin knuckle | 
Hits: 1210
Size: 67.76 KB
Posted: 10/18/03
left to right, stock 35 spline inner for '87 kingpin, 35 spline yukon outer, 30 spline stock out |
Hits: 1248
Size: 75.57 KB
Posted: 10/18/03
44 u joint compared to a 60. BIG difference | 
Hits: 1283
Size: 70.66 KB
Posted: 10/18/03
left to right, 35 spline outer, dana 44 outer, 30 spline stock outer for 60 | 
Hits: 1280
Size: 58.27 KB
Posted: 11/20/03
brand new 35 on 15x10 next to a brand new 37 on a 17x9 | 
Hits: 1510
Size: 57.06 KB
Posted: 11/20/03
bigger, but not big enuf. really want the michelins or some 40's | 
Hits: 1324
Size: 59.24 KB
Posted: 11/20/03
a shaved 14 bolt cover over a sterling rear for comparison. |
Hits: 1414
Size: 61.01 KB
Posted: 11/20/03
bye-bue POS | 
Hits: 1294
Size: 47.09 KB
Posted: 11/20/03
I had the radius arms reinforced by a competent welder, not me. | 
Hits: 1258
Size: 65.3 KB
Posted: 11/20/03
here are some comparison shots to a stock arm | 
Hits: 1187
Size: 45.28 KB
Posted: 11/20/03
| 
Hits: 1147
Size: 54.56 KB
Posted: 11/20/03
|
Hits: 1340
Size: 36.03 KB
Posted: 11/20/03
there is two ways to do a 60 with radius arms. 1. grind the wedges to fit or 2. use a spacer. i use... | 
Hits: 1315
Size: 76.59 KB
Posted: 11/20/03
this is installed and ready for the lower coil mount | 
Hits: 1286
Size: 66.96 KB
Posted: 11/20/03
before I put the spacer in, i tried to figure out the lower coil reatiner. thanks to Chris C. i mad... | 
Hits: 1455
Size: 63.89 KB
Posted: 11/20/03
| 
Hits: 1197
Size: 63.89 KB
Posted: 11/20/03
|
Hits: 1198
Size: 62.25 KB
Posted: 11/20/03
here is what Bill and i made | 
Hits: 1252
Size: 61.26 KB
Posted: 11/20/03
installed with recessed 7/16 bolts for stock radius arm and cap with 5/8 for ttb retainer | 
Hits: 1261
Size: 46.76 KB
Posted: 11/20/03
bracket with retainer and spring. it adds about 2" over the stock lower 79 reteiner I had with the ... | 
Hits: 1219
Size: 50.16 KB
Posted: 11/20/03
this holds the ttb coil much better than the 79 lower mount | 
Hits: 1335
Size: 53.33 KB
Posted: 12/1/03
new lower shock mounts are done for now, till i do a shackle flip. that is a 6 ton jackstand for re... |
Hits: 1228
Size: 57.5 KB
Posted: 12/1/03
no more shock anchors to slow me down. the 10.25 is a big axle though. 40's would be very nice.
I... | 
Hits: 1218
Size: 66.03 KB
Posted: 12/1/03
Had to clearance the 79 radius arm bracket on the drivers side to clear the driveshaft. the 88 dana... | 
Hits: 1271
Size: 69.61 KB
Posted: 12/1/03
the 60 is in, just waiting to finish the longer center link and track bar. Used the stock '79 D44 l... | 
Hits: 1327
Size: 63.83 KB
Posted: 12/12/03
the whole front done. the spirngs are bowed in a little now, that could have been solved by putting... | 
Hits: 1313
Size: 65.79 KB
Posted: 12/12/03
closeup of pass side with lower trackbar mount (kinda) |
Hits: 1517
Size: 78.69 KB
Posted: 12/12/03
closer shot of trsckbsr/draglink angles. I used a stock ford, F350 steering arm as it is much beefi... | 
Hits: 1150
Size: 54.97 KB
Posted: 12/12/03
I used the 44 brakelines, and made this little bracket to attach to the breather bolt | 
Hits: 1508
Size: 75.46 KB
Posted: 12/12/03
the new lower mounts raised the front a bit, and i definately have enuf room for the 37's and 40's s... | 
Hits: 1306
Size: 58.13 KB
Posted: 12/13/03
fullside shot with chessy/lab for rough height comparison | 
Hits: 1290
Size: 46.79 KB
Posted: 12/13/03
I have a bit over 28" at the rockers |
Hits: 1194
Size: 66.02 KB
Posted: 12/15/03
| 
Hits: 1122
Size: 63.74 KB
Posted: 12/15/03
| 
Hits: 1267
Size: 58.47 KB
Posted: 4/16/04
1" heims with 3/4 " bolts and spacers. the brackets were made to cover/use all holes made for all t... | 
Hits: 1186
Size: 41.85 KB
Posted: 4/16/04
drivers side extension. here you can see that there is a little extra space, it will be used for a ... | |
one ton upgrade