Damon Haas > 1994 Ford Bronco > open folder one ton upgrade

in the beginning
Url
Tag
Img
Thumb
passanger side spring and sway bar mounts
Url
Tag
Img
Thumb
passanger side gone, still some grinding to do to make room for the radius arm mounts
Url
Tag
Img
Thumb
drivers side brackets. Also a decent shot of the top of a kingpin knuckle
Url
Tag
Img
Thumb
left to right, stock 35 spline inner for '87 kingpin, 35 spline yukon outer, 30 spline stock out
Url
Tag
Img
Thumb
44 u joint compared to a 60. BIG difference
Url
Tag
Img
Thumb
left to right, 35 spline outer, dana 44 outer, 30 spline stock outer for 60
Url
Tag
Img
Thumb
brand new 35 on 15x10 next to a brand new 37 on a 17x9
Url
Tag
Img
Thumb
bigger, but not big enuf. really want the michelins or some 40's
Url
Tag
Img
Thumb
a shaved 14 bolt cover over a sterling rear for comparison.
Url
Tag
Img
Thumb
bye-bue POS
Url
Tag
Img
Thumb
I had the radius arms reinforced by a competent welder, not me.
Url
Tag
Img
Thumb
here are some comparison shots to a stock arm
Url
Tag
Img
Thumb
Url
Tag
Img
Thumb
Url
Tag
Img
Thumb
there is two ways to do a 60 with radius arms. 1. grind the wedges to fit or 2. use a spacer. i use...
Url
Tag
Img
Thumb
this is installed and ready for the lower coil mount
Url
Tag
Img
Thumb
before I put the spacer in, i tried to figure out the lower coil reatiner. thanks to Chris C. i mad...
Url
Tag
Img
Thumb
Url
Tag
Img
Thumb
Url
Tag
Img
Thumb
here is what Bill and i made
Url
Tag
Img
Thumb
installed with recessed 7/16 bolts for stock radius arm and cap with 5/8 for ttb retainer
Url
Tag
Img
Thumb
bracket with retainer and spring. it adds about 2" over the stock lower 79 reteiner I had with the ...
Url
Tag
Img
Thumb
this holds the ttb coil much better than the 79 lower mount
Url
Tag
Img
Thumb
new lower shock mounts are done for now, till i do a shackle flip. that is a 6 ton jackstand for re...
Url
Tag
Img
Thumb
no more shock anchors to slow me down. the 10.25 is a big axle though. 40's would be very nice. I...
Url
Tag
Img
Thumb
Had to clearance the 79 radius arm bracket on the drivers side to clear the driveshaft. the 88 dana...
Url
Tag
Img
Thumb
the 60 is in, just waiting to finish the longer center link and track bar. Used the stock '79 D44 l...
Url
Tag
Img
Thumb
the whole front done. the spirngs are bowed in a little now, that could have been solved by putting...
Url
Tag
Img
Thumb
closeup of pass side with lower trackbar mount (kinda)
Url
Tag
Img
Thumb
closer shot of trsckbsr/draglink angles. I used a stock ford, F350 steering arm as it is much beefi...
Url
Tag
Img
Thumb
I used the 44 brakelines, and made this little bracket to attach to the breather bolt
Url
Tag
Img
Thumb
the new lower mounts raised the front a bit, and i definately have enuf room for the 37's and 40's s...
Url
Tag
Img
Thumb
fullside shot with chessy/lab for rough height comparison
Url
Tag
Img
Thumb
I have a bit over 28" at the rockers
Url
Tag
Img
Thumb
Url
Tag
Img
Thumb
Url
Tag
Img
Thumb
1" heims with 3/4 " bolts and spacers. the brackets were made to cover/use all holes made for all t...
Url
Tag
Img
Thumb
drivers side extension. here you can see that there is a little extra space, it will be used for a ...
Url
Tag
Img
Thumb
 
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2022 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog