Damon Haas > 1994 Ford Bronco > open folder storage/shelf

I cut some 3/8 plywood to fit between the back of the front seats and little ledge in front of the b...
Hits: 877
Size: 45.52 KB
Posted: 8/20/04
I cut some 3/8 plywood to fit between the back of the front seats and little ledge in front of the b...		i learned the hard way that the hing needs to be right on the edge to allow the shelf to fold up. I...
Hits: 853
Size: 51.18 KB
Posted: 8/20/04
i learned the hard way that the hing needs to be right on the edge to allow the shelf to fold up. I...		top of the shelf carpeted. i had to clearance the shelf a little more on the drivers side.
Hits: 825
Size: 66.16 KB
Posted: 8/20/04
top of the shelf carpeted. i had to clearance the shelf a little more on the drivers side.		I took some time and made sure that the hinges, when mounted, would leave the shlef as level with th...
Hits: 870
Size: 55.82 KB
Posted: 8/20/04
I took some time and made sure that the hinges, when mounted, would leave the shlef as level with th...		this is the amount of gap I required, and it could actually be made a little larger or the joint mov...
Hits: 747
Size: 65.34 KB
Posted: 8/20/04
this is the amount of gap I required, and it could actually be made a little larger or the joint mov...
I made a deck, that will hold both amps (when I am done) on one side, and secured the shelf supports...
Hits: 829
Size: 61.49 KB
Posted: 8/20/04
I made a deck, that will hold both amps (when I am done) on one side, and secured the shelf supports...		the screws holding the support are barely noticeable with the carpeting
Hits: 840
Size: 88.98 KB
Posted: 8/20/04
the screws holding the support are barely noticeable with the carpeting		should be enough clearance to keep the amps and inverter (once installed) cool.
Hits: 838
Size: 57.99 KB
Posted: 8/20/04
should be enough clearance to keep the amps and inverter (once installed) cool.		The shelf in, with the rear carpeting on top of the seam, instead of down the ledge, and the carpete...
Hits: 768
Size: 59.59 KB
Posted: 8/20/04
The shelf in, with the rear carpeting on top of the seam, instead of down the ledge, and the carpete...		Full shelf without the sub. Should fake out would be's
Hits: 1084
Size: 53.81 KB
Posted: 8/20/04
Full shelf without the sub. Should fake out would be's
I was going to use this sub box, but its a little big, so i will have to find/make a smaller one.
Hits: 839
Size: 53.78 KB
Posted: 8/20/04
I was going to use this sub box, but its a little big, so i will have to find/make a smaller one.		I was also going to cut section from the tape towards the back, and then use carpeted wood in its pl...
Hits: 941
Size: 55.14 KB
Posted: 8/20/04
I was also going to cut section from the tape towards the back, and then use carpeted wood in its pl...		I welded some angle iron on to my swing away to mount some axleshafts etc.
Hits: 796
Size: 81.7 KB
Posted: 8/20/04
I welded some angle iron on to my swing away to mount some axleshafts etc.		these are mounts I sourced through work. Lots of fire depts use these to mount assorted tools.
Hits: 743
Size: 49.93 KB
Posted: 8/20/04
these are mounts I sourced through work. Lots of fire depts use these to mount assorted tools.		They can hold axle shafts, my 8 pound sledge, and hi lifts with ease. Im assured that sun and weat...
Hits: 842
Size: 64.74 KB
Posted: 8/20/04
They can hold axle shafts, my 8 pound sledge, and hi lifts with ease. Im assured that sun and weat...
Here is how my tire carrier looks. the old 5 on 5.5 tire carrier has been changed to 8 on 6.5, and ...
Hits: 900
Size: 68.59 KB
Posted: 8/20/04
Here is how my tire carrier looks. the old 5 on 5.5 tire carrier has been changed to 8 on 6.5, and ...
Hits: 846
Size: 41.29 KB
Posted: 8/25/04

Hits: 807
Size: 53.03 KB
Posted: 8/25/04
  
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2022 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog