|
|
Hits: 927
Size: 57.58 KB
Posted: 3/19/05
full shot of rear side of mount | 
Hits: 853
Size: 61.16 KB
Posted: 3/19/05
how the kolune will mount. uses 60's chevy motor mounts and some 3/8 plate | 
Hits: 925
Size: 60.39 KB
Posted: 3/19/05
how it will mount to the frame. | 
Hits: 925
Size: 48.03 KB
Posted: 3/19/05
how the tranny will mount. Will use a piece of round tube bent in a horshoe. The tranny bolts are ... | 
Hits: 959
Size: 59.56 KB
Posted: 3/19/05
sorta how the horshoe will look |
Hits: 884
Size: 52.46 KB
Posted: 3/19/05
whole front side of mount. Will have plenty of driveshaft clearance without notching, at least it l... | 
Hits: 929
Size: 59.23 KB
Posted: 3/19/05
drawn in second crossmember | 
Hits: 901
Size: 63.24 KB
Posted: 3/21/05
| 
Hits: 1050
Size: 58.54 KB
Posted: 3/21/05
| 
Hits: 1383
Size: 59.43 KB
Posted: 3/21/05
this will leave room for the belly pan and should sit about level with the bottom of the frame brack... |
Hits: 1100
Size: 50.89 KB
Posted: 4/2/05
making progress. The mount is 3/8, so I figure only two gussets would be required. | 
Hits: 950
Size: 60.11 KB
Posted: 4/2/05
just need to figure this out now. | 
Hits: 920
Size: 51.15 KB
Posted: 4/3/05
in the end, i changed my mind and am going to try this. Notice here, the driveshaft clearance in th... | 
Hits: 852
Size: 61.85 KB
Posted: 4/6/05
clearance to body | 
Hits: 1005
Size: 60.82 KB
Posted: 4/6/05
|
Hits: 951
Size: 69.06 KB
Posted: 4/6/05
painted and installed | 
Hits: 909
Size: 63.7 KB
Posted: 4/6/05
| 
Hits: 863
Size: 56.41 KB
Posted: 4/6/05
| 
Hits: 899
Size: 58.18 KB
Posted: 4/6/05
| 
Hits: 854
Size: 49.21 KB
Posted: 4/6/05
|
Hits: 855
Size: 68.91 KB
Posted: 4/6/05
| 
Hits: 908
Size: 63.3 KB
Posted: 4/6/05
| 
Hits: 874
Size: 53.32 KB
Posted: 4/6/05
| 
Hits: 845
Size: 42.34 KB
Posted: 4/6/05
| 
Hits: 815
Size: 69.41 KB
Posted: 5/2/05
this is the back side xmember. This will allow me a mount for a rear axle torque arm, will be the r... |
Hits: 939
Size: 85.97 KB
Posted: 5/2/05
drivers side shot. The rear and front XM's are within an 1/8 inch from the ground of one another. | 
Hits: 855
Size: 73.51 KB
Posted: 5/2/05
I ended up keeping the e brake bracket in the stock position (except for 3/8" off the frame noe for ... | 
Hits: 856
Size: 46.03 KB
Posted: 5/2/05
its a bad pic, but the 205 hangs down about .5 inches below the XMs | 
Hits: 871
Size: 77.48 KB
Posted: 5/2/05
just a series of the stock 205 torque arm mount, that usually mounts to the 78 style frame instead o... | 
Hits: 802
Size: 84.24 KB
Posted: 5/2/05
I turned the stock lower mount 90 degrees and welded this 1/4 plate to the XM. then, using 3/8 bolt... |
Hits: 905
Size: 82.65 KB
Posted: 5/2/05
its a close fit, but clears the 205 AND the fuel filter | 
Hits: 812
Size: 63.52 KB
Posted: 5/2/05
after paint and before install. | | | |
doubler crossmember