|
|
Hits: 115
Size: 92.88 KB
Posted: 2/11/17
Now that those pesky fender liners are out of the way I have unrestricted access to the manifold bol... | 
Hits: 93
Size: 63.1 KB
Posted: 2/11/17
Doing this from the top isn't really a viable option, if you don't want to pull the liners. Doable b... | 
Hits: 95
Size: 149.39 KB
Posted: 2/11/17
OUT! Passenger side manifold.There are two brackets bolted to the back of the cylinder head (both ut... | 
Hits: 83
Size: 61.11 KB
Posted: 2/11/17
The hard part. I fully expected to not even get to 50% completion today. Both bolts in cylinder 4 (f... | 
Hits: 113
Size: 77.88 KB
Posted: 2/19/17
Just for two exhaust manifold bolts.... |
Hits: 103
Size: 46.65 KB
Posted: 2/19/17
Well, good thing I did pull the head. Ran fine...surprising well, actually. This explains a few thin... | 
Hits: 42
Size: 77.88 KB
Posted: 3/9/17
Getting there. Intake gaskets have been leaking for some time. I am surprised at how clean the valle... | 
Hits: 67
Size: 64.91 KB
Posted: 3/9/17
Such a purdy head gasket. | 
Hits: 75
Size: 76.25 KB
Posted: 3/9/17
Looks like some fun is about to happen. | 
Hits: 57
Size: 34.62 KB
Posted: 3/9/17
Hm. Going to need new valves. I had one or two better, some worse. Going to need new valves. Oh well... |
Hits: 59
Size: 46.06 KB
Posted: 3/9/17
Valve seat. Can't remember if this is before or after lapping. I think after? 3 hours per head to do... | 
Hits: 71
Size: 57.75 KB
Posted: 3/10/17
Getting there...Stilll needs FEAD bolted up and bolt up the oil pan. Much as I did not want to tear ... | 
Hits: 92
Size: 43.03 KB
Posted: 3/10/17
Ah, finally! I am at the point where I should have been two weeks ago. Header is there just for mock... | 
Hits: 86
Size: 105.47 KB
Posted: 3/13/17
Need to pull the EGR elbow out of the driver side manifold. | 
Hits: 74
Size: 91.93 KB
Posted: 3/13/17
Well....that just happened. If you expect us to pay $100 for a stpuid fitting, Ford, we expect $100 ... |
Hits: 87
Size: 125.67 KB
Posted: 3/13/17
Added bonus! EGR tube is junk. Wonder how long it has been split open.... | 
Hits: 87
Size: 82.65 KB
Posted: 3/13/17
It is an engine again! Note: Ford Racing 302 wires, PN: FMS-M-12259-C301, fit ALMOST perfect on a 46... | 
Hits: 110
Size: 84.12 KB
Posted: 3/13/17
Wire separators are far too under appreciated on a daily driver. First time using the zip tie-wire s... | 
Hits: 120
Size: 61.95 KB
Posted: 3/21/17
F*** you Ford. A piece of metal that is the size of an egg costs that much....EGR tube fitting. At l... | 
Hits: 101
Size: 82.02 KB
Posted: 3/23/17
Hedman, the master of mediocrity strikes again. Y-pipe does not fit; although I do not think I can c... |
Hits: 158
Size: 89.86 KB
Posted: 3/28/17
"Fixed" y-pipe....both my stupid moment fix and Hedmans unfit problem. Only needed a fract... | | | | |
Header Install turned Head job