Jeremy Millrood > 1992 Ford Bronco > open folder Powersteering Gearbox Rebuild

To make it easier to work on remove the airinlet tube from the air box, and set it aside. If you can...
Hits: 1308
Size: 116.91 KB
Posted: 10/27/03
To make it easier to work on remove the airinlet tube from the air box, and set it aside. If you can...		These three bolts must be removed for the powersteering box to come off of the frame.
Hits: 1343
Size: 100.66 KB
Posted: 11/5/03
These three bolts must be removed for the powersteering box to come off of the frame.		When removing the steering shaft from the sector shaft, it helps to have to sets of hands. The bolt ...
Hits: 1324
Size: 61.32 KB
Posted: 10/31/03
When removing the steering shaft from the sector shaft, it helps to have to sets of hands. The bolt ...		Removing the return lines was a little difficult, this probably took the most time, mine had never b...
Hits: 1370
Size: 69.47 KB
Posted: 10/31/03
Removing the return lines was a little difficult, this probably took the most time, mine had never b...		Getting ready to remove the pitman arm with a puller, you definitely want to use a puller.
Hits: 1382
Size: 46.41 KB
Posted: 10/31/03
Getting ready to remove the pitman arm with a puller, you definitely want to use a puller.
Pitman arm about to come off.
Hits: 1337
Size: 73.13 KB
Posted: 10/27/03
Pitman arm about to come off.		Pitman arm finally removed.
Hits: 1400
Size: 72.79 KB
Posted: 10/27/03
Pitman arm finally removed.		Once the pitman arm is removed, you can completely remove the box from your rig. There are 3 bolts g...
Hits: 1418
Size: 98.65 KB
Posted: 10/27/03
Once the pitman arm is removed, you can completely remove the box from your rig. There are 3 bolts g...		Snap ring over the trashed seal. It helps to have a good set of ring pliers.
Hits: 1321
Size: 91.08 KB
Posted: 10/27/03
Snap ring over the trashed seal. It helps to have a good set of ring pliers.		Sector shaft removed completely from the box. There was a little scoring around the shaft from wear ...
Hits: 1436
Size: 95.22 KB
Posted: 10/27/03
Sector shaft removed completely from the box. There was a little scoring around the shaft from wear ...
After sanding the sector shaft for about 15 minutes, I used a light grade sand paper to take the sco...
Hits: 1320
Size: 83.18 KB
Posted: 10/27/03
After sanding the sector shaft for about 15 minutes, I used a light grade sand paper to take the sco...		Installing the new seal. Find an appropriate sized socket so you can hammer the new seal in. You wan...
Hits: 1326
Size: 110.43 KB
Posted: 10/27/03
Installing the new seal. Find an appropriate sized socket so you can hammer the new seal in. You wan...		The new snap ring will go right on once the seal has been seated properly. Once this is done give th...
Hits: 1239
Size: 99.68 KB
Posted: 10/27/03
The new snap ring will go right on once the seal has been seated properly. Once this is done give th...		Here is my resealed box, looks almost like new. Installation is the reverse of the removal. You may ...
Hits: 1227
Size: 106.02 KB
Posted: 10/27/03
Here is my resealed box, looks almost like new. Installation is the reverse of the removal. You may ...		 
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2022 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog