|
|
Hits: 249
Size: 85.67 KB
Posted: 6/24/14
The old insulation on my evaporator box was falling apart. I had seen people use this Reflectix insu... | 
Hits: 240
Size: 62.33 KB
Posted: 6/24/14
Here is the box, you can see how filthy it is. You only need to remove the side that covers the evap... | 
Hits: 224
Size: 55.58 KB
Posted: 6/24/14
there are about 6 screws that hold the cover on. some of them are in tough to reach places so you'll... | 
Hits: 234
Size: 55.64 KB
Posted: 6/24/14
| 
Hits: 221
Size: 72.16 KB
Posted: 6/24/14
|
Hits: 235
Size: 65.07 KB
Posted: 6/24/14
| 
Hits: 215
Size: 67.33 KB
Posted: 6/24/14
all of the screws are removed and so is the nut holding box to the firewall. I'm able to start separ... | 
Hits: 215
Size: 61.4 KB
Posted: 6/24/14
this screw/bolt is the problem..Ford in it's infinite wisdom has is attached to the box from the ins... | 
Hits: 222
Size: 61.56 KB
Posted: 6/24/14
| 
Hits: 231
Size: 56.13 KB
Posted: 6/24/14
here is a shot of the screw/bolt from the inside..it's a 10mm. |
Hits: 222
Size: 72.43 KB
Posted: 6/24/14
once that was removed it took a bit of manipulation, but the cover finally came out and there is the... | 
Hits: 220
Size: 67.7 KB
Posted: 6/24/14
| 
Hits: 239
Size: 81.03 KB
Posted: 6/24/14
here is the cover removed. | 
Hits: 243
Size: 73.18 KB
Posted: 6/24/14
| 
Hits: 224
Size: 73.25 KB
Posted: 6/24/14
cover all cleaned up. |
Hits: 219
Size: 53.88 KB
Posted: 6/24/14
checked the reservoir for vacuum and it holds. | 
Hits: 234
Size: 82.79 KB
Posted: 6/24/14
started cutting the insulation and covering the box. | 
Hits: 211
Size: 83.23 KB
Posted: 6/24/14
tedious process and a bit of trial and error. | 
Hits: 245
Size: 82.24 KB
Posted: 6/24/14
getting closer. | 
Hits: 234
Size: 74.31 KB
Posted: 6/24/14
finished product. hopefully this should help keep some of the engine heat out of the ducts and help ... |
Hits: 229
Size: 57.03 KB
Posted: 6/25/14
you should clean out the cowl drains while you have the inner fender pulled. this one was clean.. | 
Hits: 228
Size: 95.46 KB
Posted: 6/25/14
while I have everything pulled apart, I wanted to check the evaporator they can accumulate a lot of ... | 
Hits: 220
Size: 95.34 KB
Posted: 6/25/14
flushed from the back with water and blown with compressed air..looks good. | 
Hits: 230
Size: 65.48 KB
Posted: 6/25/14
seems like this is the factory evap. I've never replaced since I bought the rig and that's almost 20... | 
Hits: 235
Size: 88.57 KB
Posted: 6/25/14
added a few more pieces of insulation to the box, figured that would help improve the R value and ke... |
Hits: 213
Size: 75.39 KB
Posted: 6/25/14
I almost forgot about about the bottom of the box. this was the other half and it was also covered w... | 
Hits: 233
Size: 73.98 KB
Posted: 6/25/14
bottom view. doubled up on the insulation here. I think that should work pretty well...I may still g... | 
Hits: 255
Size: 83.72 KB
Posted: 6/26/14
| 
Hits: 258
Size: 48.42 KB
Posted: 6/30/14
Testing my A/C...it was over 101 yesterday. granted, that was in the sun..not sure what the heat ind... | 
Hits: 229
Size: 53.97 KB
Posted: 6/30/14
set the system to Max A/C with the windows down and this was the best it would do..
so you figure a... |
Evaporator Box R&R