|
|
 IMG_20160903_104645148-1280x960.jpg | Hits: 244 | Size: 44.47 KB | Posted on: 10/27/16 | Link to this image
|
|
|
 IMG_20161204_155147042-3120x2340.jpg | Hits: 199 | Size: 49.38 KB | Posted on: 12/5/16 | Link to this image
|
|
|
 IMG_20161204_155159494-3120x2340.jpg | Hits: 194 | Size: 54.57 KB | Posted on: 12/5/16 | Link to this image
|
|
|
 IMG_20161204_155214243_HDR-3120x2340.jpg | Hits: 204 | Size: 57.72 KB | Posted on: 12/5/16 | Link to this image
|
|
|
 IMG_20161204_155224864-3120x2340.jpg | Hits: 224 | Size: 61.55 KB | Posted on: 12/5/16 | Link to this image
|
|
|
 IMG_20161204_155235996-3120x2340.jpg | Hits: 181 | Size: 46.21 KB | Posted on: 12/5/16 | Link to this image
|
|
|
 IMG_20161212_125943688_TOP-3120x2340.jpg | Hits: 187 | Size: 55.93 KB | Posted on: 12/12/16 | Link to this image
|
|
|
 IMG_20161212_130149322_TOP-3120x2340.jpg | Hits: 205 | Size: 59.83 KB | Posted on: 12/12/16 | Link to this image
|
|
|
 IMG_20161212_140249648_HDR-3120x2340.jpg | Hits: 220 | Size: 68.64 KB | Posted on: 12/12/16 | Link to this image
Old rubber c-bushings (7 degree). These were completely split in half.
|
|
|
 IMG_20161215_193436185-2340x3120.jpg | Hits: 261 | Size: 50.64 KB | Posted on: 12/16/16 | Link to this image
Radius arm cap bolt kit from Wild Horses. This was intended for the earlier Broncos but works on the '78 or '79 axles as well. The bolts are slightly shorter than stock but still thread completely through the back of the cap.
came with 8, 9/16 - 2 inch cap bolts, 2 3.5 inch 9/16 bolts, lock washer, replacement castle nuts and cotter pins for the track bar and replacement bushings.
|
|
|
 IMG_20161215_193551249-3120x2340.jpg | Hits: 227 | Size: 55.5 KB | Posted on: 12/16/16 | Link to this image
Bolt kit laid out.
|
|
|
 IMG_20161217_092455918-3120x2340.jpg | Hits: 241 | Size: 55.48 KB | Posted on: 12/17/16 | Link to this image
new radius arm cap bolts installed. did not use loctite,
|
|
|
 IMG_20161217_092505716-3120x2340.jpg | Hits: 241 | Size: 50.85 KB | Posted on: 12/17/16 | Link to this image
|
|
|
 IMG_20161217_092519054-3120x2340.jpg | Hits: 247 | Size: 53.52 KB | Posted on: 12/17/16 | Link to this image
|
|
|
 IMG_20161229_153323973_HDR-3120x2340.jpg | Hits: 202 | Size: 50.1 KB | Posted on: 12/31/16 | Link to this image
New steering linkage hardware for the tie rod and drag link, clearance and spacer shims from Bulletproof steering. Stuff is not inexpensive but great quality and should last the life of the truck.
|
|
|
 IMG_20161229_153331198_HDR-3120x2340.jpg | Hits: 178 | Size: 52.3 KB | Posted on: 12/31/16 | Link to this image
|
|
|
 IMG_20180509_154726883_LL.jpg | Hits: 101 | Size: 53.94 KB | Posted on: 5/10/18 | Link to this image
7 degree c-bushings from energy suspension. I've got about 3.5 degrees of caster. not nearly enough for the solid axle. this should correct the problem.
|
Radius Arm C-bushings and hardware