Jeremy Millrood > 1992 Ford Bronco > open folder Dana 44 front pinion seal


Hits: 163
Size: 50.69 KB
Posted: 11/20/16
Dana 44 pinion seal from NAPA PN 15788
Hits: 166
Size: 66.62 KB
Posted: 11/20/16
Dana 44 pinion seal from NAPA PN 15788		Replacement pinion nut, sourced from Ace hardware, 3/4 16 thread stover nut. stover nuts derive th...
Hits: 252
Size: 61.61 KB
Posted: 11/20/16
Replacement pinion nut, sourced from Ace hardware, 3/4 16 thread stover nut. stover nuts derive th...
Hits: 156
Size: 65.26 KB
Posted: 11/20/16
1/2 inch ratchet wrench to remove u joint retainer bolts.
Hits: 176
Size: 53.64 KB
Posted: 11/20/16
1/2 inch ratchet wrench to remove u joint retainer bolts.
clamped the end caps on the u-joints so they fall off.
Hits: 162
Size: 60.39 KB
Posted: 11/20/16
clamped the end caps on the u-joints so they fall off.		ready to remove the pinion nut. it's 1 1/8 inch. used an impact gun while holding the yoke in place.
Hits: 151
Size: 49.9 KB
Posted: 11/20/16
ready to remove the pinion nut. it's 1 1/8 inch. used an impact gun while holding the yoke in place.		After hammering around the edges of the old seal with a screwdriver, I was able to bend it in enough...
Hits: 174
Size: 62.42 KB
Posted: 11/20/16
After hammering around the edges of the old seal with a screwdriver, I was able to bend it in enough...
Hits: 127
Size: 49.47 KB
Posted: 11/20/16
nut removed but the threads on the pinion shaft were stripped. this is going to be a problem.
Hits: 203
Size: 47.27 KB
Posted: 11/20/16
nut removed but the threads on the pinion shaft were stripped. this is going to be a problem.
this is what the inside of the nut looked like, completely trashed. these should be replaced any tim...
Hits: 192
Size: 44.25 KB
Posted: 11/20/16
this is what the inside of the nut looked like, completely trashed. these should be replaced any tim...		my yoke (1330) was rusty and pitted, so it's a good idea to clean up the part that rides on the seal...
Hits: 182
Size: 47.56 KB
Posted: 11/20/16
my yoke (1330) was rusty and pitted, so it's a good idea to clean up the part that rides on the seal...		Applied a really fine coating of RTV to the mounting surface of the seal and tapped it in place with...
Hits: 184
Size: 54.8 KB
Posted: 11/20/16
Applied a really fine coating of RTV to the mounting surface of the seal and tapped it in place with...		seal in place, next step is to rethread the pinion shaft. I was told this couldn't or rather shouldn...
Hits: 251
Size: 56.07 KB
Posted: 11/25/16
seal in place, next step is to rethread the pinion shaft. I was told this couldn't or rather shouldn...		To re-cut the threads on the shaft I ordered a 3/4 inch 16 thread carbon steel re-threading die. Cos...
Hits: 247
Size: 54.36 KB
Posted: 11/25/16
To re-cut the threads on the shaft I ordered a 3/4 inch 16 thread carbon steel re-threading die. Cos...
Re-threaded with the new pinion nut on. I was able to crank it down even more than what is in the pi...
Hits: 196
Size: 55.06 KB
Posted: 11/25/16
Re-threaded with the new pinion nut on. I was able to crank it down even more than what is in the pi...		    
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2022 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog