|
|
Hits: 79
Size: 111.42 KB
Posted: 5/4/21
| 
Hits: 35
Size: 120.5 KB
Posted: 5/4/21
Hurst Pro-Matic shifter from Craigslist. Has PRND21 which matches the 4R70W pattern since O/D is lo... | 
Hits: 62
Size: 134.62 KB
Posted: 5/4/21
Hurst shift cable mounted to the transmission lever with the end of the stock Bronco carburetor link... | 
Hits: 49
Size: 133.98 KB
Posted: 5/4/21
Bosch 69100 fuel pump mounted low to feed off the carburetor style sending unit. WIX 33270 150 micro... | 
Hits: 38
Size: 134.59 KB
Posted: 5/4/21
Full engine bay harness from the Explorer. Starting to peel off the tape to see the rainbow inside. |
Hits: 72
Size: 134.75 KB
Posted: 5/4/21
Chomp! Cut the main harness just past the relay box, which is in the area behind the driver's headl... | 
Hits: 64
Size: 138.28 KB
Posted: 5/4/21
Ahhh, scary wiring! This is after cutting off the 3 firewall connectors. Lots of wires can be remo... | 
Hits: 62
Size: 108.66 KB
Posted: 5/4/21
These are the wires I removed from C115 because they are not needed. It's cleaner to remove them ra... | 
Hits: 65
Size: 112.58 KB
Posted: 5/4/21
Getting less scary! The 7 circuits left in place are in the split loom tubing. The big bundle of w... | 
Hits: 59
Size: 121.25 KB
Posted: 5/4/21
PDB mounting bracket cut and welded on backwards so that it mounts downward and the box sits over th... |
Hits: 58
Size: 129.01 KB
Posted: 5/4/21
The 3 grounds from C115 ground to the old voltage regulator ground. I wire wheeled the metal bare t... | 
Hits: 29
Size: 128.94 KB
Posted: 5/18/21
We used a piece of a broken aluminum yard stick to move the P/S reservoir down and back. It wasn't ... | 
Hits: 33
Size: 84.98 KB
Posted: 5/18/21
The EGR solenoid was too high (surprise, surprise... do a body lift first!) so we took the mounting ... | 
Hits: 26
Size: 138.13 KB
Posted: 5/18/21
We took the MAF out of the airbox and mounted it to the fender. With a little help from the heat gu... | 
Hits: 24
Size: 74.74 KB
Posted: 5/18/21
The air filter came with the plate and gasket that mounted right up to the MAF sensor. Search eBay ... |
Hits: 32
Size: 129.87 KB
Posted: 5/18/21
We'll have to figure out a solution for the fan shroud since the fan is almost completely outside it... | 
Hits: 27
Size: 127.35 KB
Posted: 5/18/21
We used the Explorer's throttle cable but it angled upward into the hood too much so we cut the lowe... | 
Hits: 31
Size: 131.83 KB
Posted: 5/18/21
The oil filler ran into the intake tube and I just happened to have a Buick 3.8 sitting on the shop ... | 
Hits: 33
Size: 130.57 KB
Posted: 5/18/21
Another shot of the radiator hose attaching the filler tube. | 
Hits: 31
Size: 142.59 KB
Posted: 5/18/21
Nearly finished. We were going to keep the A/C lines for potential future use but we're going to ya... |
Hits: 51
Size: 152.19 KB
Posted: 5/18/21
These 3 connectors were originally in the engine bay.
The 4-pin square connector is used for th... | 
Hits: 51
Size: 53.74 KB
Posted: 5/18/21
Overdrive cancel switch and LED. There was a big hole here already so in it went. The LED has a fai... | 
Hits: 66
Size: 82.41 KB
Posted: 5/18/21
This is the alternator charge light and it does need to be a bulb rather than a LED, preferably with... | 
Hits: 46
Size: 74.45 KB
Posted: 5/18/21
OBD2 port (AKA DLC) for diagnostics. It has 3 wires from C115 and then a power and ground wire. La... | 
Hits: 61
Size: 129.28 KB
Posted: 5/18/21
Eight lonely fuses, two relays, and a diode are all that's left. |
Hits: 58
Size: 133.73 KB
Posted: 5/18/21
Since the Bronco doesn't have a true RUN/START circuit from the factory, we created one with a bridg... | 
Hits: 67
Size: 140.28 KB
Posted: 5/18/21
The Explorer starter solenoid coil grounds through its case so we removed the paint from the wheel h... | 
Hits: 58
Size: 130.09 KB
Posted: 5/18/21
This still needs a little cleanup but it's just a busy area for wiring. C115 splits into 3 groups h... | 
Hits: 64
Size: 133.29 KB
Posted: 5/18/21
Arial view of the PDB. These wires now have split loom protecting them. To the right of the PDB yo... | 
Hits: 29
Size: 127.35 KB
Posted: 7/3/21
We had cut a section out of the throttle bracket at the bottom and weld it back together to clock th... |
Hits: 34
Size: 84.8 KB
Posted: 7/3/21
The finished product! It turned out fairly clean but it sure would've made sense to paint the engin... | 
Hits: 30
Size: 116.85 KB
Posted: 7/3/21
We were adjusting the shift linkage when a cloud of stinky smoke came out from under the hood. We f... | 
Hits: 36
Size: 59.23 KB
Posted: 7/3/21
The test drive was awesome! This thing flies compared to when it had the 302 and C6. It even leave... | | |
Explorer 5.0 and 4R70W swap