|
|
Hits: 2923
Size: 64.24 KB
Posted: 9/14/04
Warn 9k winch, 55 lbs. Solenoid, fairlead and wiring, 20lbs. add the mount and total weight apx. 10... | 
Hits: 2907
Size: 41.51 KB
Posted: 9/14/04
mount is made of 8" Structural C channel, 11.5# with 2" sides, bottom is equivalent to 1/4" steel, b... | 
Hits: 2603
Size: 45.48 KB
Posted: 9/14/04
before cutting this 38" piece is 33lbs. after it was 26. | 
Hits: 2716
Size: 65.04 KB
Posted: 9/14/04
| 
Hits: 3089
Size: 57.62 KB
Posted: 9/14/04
test fit after cutting. |
Hits: 2761
Size: 62.26 KB
Posted: 9/14/04
The rear 2" side was cut down to about 1.25". Just enough room to clear tranny lines | 
Hits: 2979
Size: 61.57 KB
Posted: 9/14/04
| 
Hits: 3110
Size: 60.16 KB
Posted: 9/14/04
| 
Hits: 2597
Size: 56.06 KB
Posted: 9/14/04
This mount does not stick out way forward of the bumper/frame. | 
Hits: 3043
Size: 60.48 KB
Posted: 9/14/04
|
Hits: 3165
Size: 60.16 KB
Posted: 9/14/04
Same pic, fairlead added | 
Hits: 2843
Size: 67.71 KB
Posted: 9/14/04
| 
Hits: 2741
Size: 46.65 KB
Posted: 9/14/04
| 
Hits: 3811
Size: 50.47 KB
Posted: 9/14/04
| 
Hits: 2699
Size: 60.55 KB
Posted: 9/14/04
|
Hits: 2973
Size: 53.46 KB
Posted: 9/22/04
Care on the winch mount is needed, as the fairlead bolt does need about 1" of clearance or it will t... | 
Hits: 2683
Size: 58.59 KB
Posted: 9/22/04
good shot of winch mount to frame brackets, 2 for each side (one is back behind the bumper mount bra... | 
Hits: 2535
Size: 65.63 KB
Posted: 9/22/04
shot of mount from underneath looking toward the front. Note how it's cut back around the accordian... | 
Hits: 2492
Size: 57.98 KB
Posted: 9/22/04
rearmost bracket | 
Hits: 2498
Size: 58.85 KB
Posted: 9/22/04
one more shot looking underneath, toward the driver side of the vehicle. |
Hits: 2417
Size: 43.33 KB
Posted: 9/22/04
closeup of solenoid | 
Hits: 2442
Size: 50.76 KB
Posted: 9/22/04
solenoid mount again, this time with Grille removed. Note black plastic edging to protect cables. ... | 
Hits: 2599
Size: 50.36 KB
Posted: 9/22/04
beginning to work on the shackle to frame attachment. 1" x 2" x 6" steel | 
Hits: 2440
Size: 49.71 KB
Posted: 9/22/04
yep, that's 6" | 
Hits: 2802
Size: 47.66 KB
Posted: 9/22/04
once the 1" hole is cut, it needs to be carefully measured for the (2) 1/2" mounting holes. (the 1/... |
Hits: 2704
Size: 53.76 KB
Posted: 9/22/04
end result. Well not quite. It needs to ber purdied up at this point. | 
Hits: 2609
Size: 58.19 KB
Posted: 9/22/04
another angle | 
Hits: 2600
Size: 64.23 KB
Posted: 12/22/04
some of my recovery stuff, 6T WLL snatch block,10' x 2"(double wound) tree strap, 3/4" 4.75WLL D sha... | | |
Winch Mount