michael collins > 1983 Ford Bronco > open folder 3" Body Lift

Her she is before the 3" body Lift. These are 33" tires.
Hits: 611
Size: 104.7 KB
Posted: 10/11/06
Her she is before the 3" body Lift. These are 33" tires.		when i ordered the poly body mounts i got the front core support not all the bushings i needed, but ...
Hits: 547
Size: 63.71 KB
Posted: 11/3/06
when i ordered the poly body mounts i got the front core support not all the bushings i needed, but ...		Here is the PA lift as i got it from 4wheelcustoms. thanks again Chris.
Hits: 520
Size: 98.47 KB
Posted: 11/3/06
Here is the PA lift as i got it from 4wheelcustoms. thanks again Chris.		This is both front core support poly bushings and washers and sleaves. it was $26 not bad. too bad i...
Hits: 542
Size: 57.55 KB
Posted: 11/3/06
This is both front core support poly bushings and washers and sleaves. it was $26 not bad. too bad i...		This is a look in the box of the PA-3" body lift
Hits: 571
Size: 86.16 KB
Posted: 10/11/06
This is a look in the box of the PA-3" body lift
Here are the 3" body lift parts out of the box.
Hits: 590
Size: 80.37 KB
Posted: 10/11/06
Here are the 3" body lift parts out of the box.		I hit all the body mount bolts with PB Blaster for 2 week prior to installing the lift. the bolts ca...
Hits: 571
Size: 145.38 KB
Posted: 10/11/06
I hit all the body mount bolts with PB Blaster for 2 week prior to installing the lift. the bolts ca...		Here are the old and new Body mounts. the old rubber were soft and worn down.
Hits: 676
Size: 115.97 KB
Posted: 10/11/06
Here are the old and new Body mounts. the old rubber were soft and worn down. 		Here are the old body mount shells. i cleaned and painted them to stop the rusting.. the poly mounts...
Hits: 684
Size: 106.45 KB
Posted: 11/3/06
Here are the old body mount shells. i cleaned and painted them to stop the rusting.. the poly mounts...		I tossed the rubber bushings and cleaned and painted the shels. not seen i cut the nut off the botto...
Hits: 756
Size: 101.21 KB
Posted: 10/11/06
I tossed the rubber bushings and cleaned and painted the shels. not seen i cut the nut off the botto...
Here is all the hardware. ready to reinstall.
Hits: 606
Size: 91.55 KB
Posted: 10/11/06
Here is all the hardware. ready to reinstall.		Here is the drivers side before the lift was installed.
Hits: 618
Size: 84.41 KB
Posted: 11/3/06
Here is the drivers side before the lift was installed.		This is the stock front Body mount before the 3" body lift and poly mount gets installed.
Hits: 599
Size: 80.68 KB
Posted: 12/3/06
This is the stock front Body mount before the 3" body lift and poly mount gets installed.		After all the bolts were out and the shells split apart. I started to jack the body up. (Look for wi...
Hits: 577
Size: 89.58 KB
Posted: 10/11/06
After all the bolts were out and the shells split apart. I started to jack the body up. (Look for wi...		Here is the front blocked up. the raditor support mount is different than all the other mounts. it b...
Hits: 639
Size: 92.66 KB
Posted: 10/11/06
Here is the front blocked up. the raditor support mount is different than all the other mounts. it b...
here is how they go together. when doing the lift this way i did not lock tite the bolts till the ot...
Hits: 734
Size: 83.98 KB
Posted: 10/11/06
here is how they go together. when doing the lift this way i did not lock tite the bolts till the ot...		you can see the whole space is 4 1/2" space after the poly body mounts and body lift kit.
Hits: 615
Size: 43.48 KB
Posted: 10/11/06
you can see the whole space is 4 1/2" space after the poly body mounts and body lift kit.		Here is alook from a few feet back. body mount and lift installed. Oh yea my two sons that are part ...
Hits: 583
Size: 86.38 KB
Posted: 10/11/06
Here is alook from a few feet back. body mount and lift installed. Oh yea my two sons that are part ...		Here is a shot with the driverside front. remember to replace all shims in the correct location. the...
Hits: 630
Size: 79.12 KB
Posted: 10/11/06
Here is a shot with the driverside front. remember to replace all shims in the correct location. the...		I planed this to goe over 2 days. saturday for the drivers side and sunday for the pass side. i want...
Hits: 650
Size: 104.01 KB
Posted: 10/11/06
I planed this to goe over 2 days. saturday for the drivers side and sunday for the pass side. i want...
here is a look from the front with only the driver side completed.
Hits: 815
Size: 95.17 KB
Posted: 10/11/06
here is a look from the front with only the driver side completed.		Here is the rear end with the driverside done (my new to me 35" thornturds in the back).
Hits: 708
Size: 80.04 KB
Posted: 10/11/06
Here is the rear end with the driverside done (my new to me 35" thornturds in the back).		just looks strange with 1/2 way done.
Hits: 725
Size: 100.35 KB
Posted: 10/11/06
just looks strange with 1/2 way done.		the same steps were taken on the pass side.and here is a side shot with it completly locktited and t...
Hits: 943
Size: 102.69 KB
Posted: 10/11/06
the same steps were taken on the pass side.and here is a side shot with it completly locktited and t...		Here is a shot from the rear with both sides done.
Hits: 632
Size: 88.97 KB
Posted: 10/11/06
Here is a shot from the rear with both sides done.
Here is the front all completed.
Hits: 622
Size: 82.73 KB
Posted: 10/11/06
Here is the front all completed.		Here Jezebel is out on the street after the new 3" body lift.
Hits: 709
Size: 97.15 KB
Posted: 11/3/06
Here Jezebel is out on the street after the new 3" body lift.		This was taken a short time later. (the bumpers were not done at the body lift time) this is out on ...
Hits: 663
Size: 81.54 KB
Posted: 10/11/06
This was taken a short time later. (the bumpers were not done at the body lift time) this is out on ...		Here is the front after the body lift.
Hits: 585
Size: 71.23 KB
Posted: 11/3/06
Here is the front after the body lift.		Here is the heigth after the body mount and 3" lift kit were installed.
Hits: 583
Size: 58.01 KB
Posted: 10/11/06
Here is the heigth after the body mount and 3" lift kit were installed.
Here is a view from the drivers side rear corner.
Hits: 565
Size: 81.48 KB
Posted: 11/3/06
Here is a view from the drivers side rear corner.		here is a second look at the back corner
Hits: 593
Size: 90 KB
Posted: 12/3/06
here is a second look at the back corner		I wanted to cover the gap left but the lift so i used a stock ford truckbed liner (free from Matt)
Hits: 620
Size: 85.65 KB
Posted: 10/11/06
I wanted to cover the gap left but the lift so i used a stock ford truckbed liner (free from Matt)		This was a standard bed bed liner. here is the bottom.
Hits: 544
Size: 47.03 KB
Posted: 11/3/06
This was a standard bed bed liner. here is the bottom.		I sliced out the bottom.
Hits: 527
Size: 91.92 KB
Posted: 10/11/06
I sliced out the bottom.
the floo is out now.
Hits: 554
Size: 95.76 KB
Posted: 10/11/06
the floo is out now.		I used a dramil and sliced the bed up.
Hits: 575
Size: 89.11 KB
Posted: 10/11/06
I used a dramil and sliced the bed up.		Here is the floor. I decided to make a liner for the bronco..
Hits: 536
Size: 84 KB
Posted: 10/11/06
Here is the floor. I decided to make a liner for the bronco..		Here is the rear bed liner with the rear seat flipped up.
Hits: 527
Size: 68.42 KB
Posted: 11/3/06
Here is the rear bed liner with the rear seat flipped up.		The floor portion i used as a bed liner in the back of the bronco. Istopped the rear seat from bounc...
Hits: 566
Size: 76.45 KB
Posted: 10/11/06
The floor portion i used as a bed liner in the back of the bronco. Istopped the rear seat from bounc...
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2022 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog